Search Documents

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By Thomas Buenger

The Hamburg smelter of Norddeutsche Affinerie AG is situated near the city of Hamburg’s downtown and is therefore particularly subjected to fulfill environmental requirements according to the German legal regulations. Thus, investments related to increasing concentrate throughput are always linked to packages to enhance the emission status of the smelter. This connection between environmental protection and productivity enhancement should be explained by the example of the Peirce-Smith converter plant of the Hamburg smelter. Such outstanding investments can be demonstrated by the transition from scrap charging via boat from the front side to a fully automatic and completely sucked scrap charging system.

Jan 1, 2009

By I. G. L. Sinclair

The Selbaie deposit is located in northern Quebec. It is comprised of three distinct, but genetically related, Cu-Zn-Ag ore bodies which also contain economically significant amounts of Au. The deposits are Archean in age and volcanogenic in origin. At Selbaie, ore microscopy has been employed to aid in planning of ore beneficiation methods and to monitor the ongoing performance of the concentrator. Examples of both types of study are described. Early in the life of the mine, excessive amounts of Zn appearing were found to be appearing in the Cu concentrate. Microscopic examination of concentrates showed that this was being caused by the presence of coatings of supergene chalcocite on sphalerite grains. Fine coatings of supergene galena and chalcopyrite were also observed on some sphalerite grains. The presence of Ag and Au in the ores makes an important contribution to the revenue of the mine. The various modes of occurrence and mineralogical relationship of these two metals are described and discussed. Monitoring of the ongoing concentrating process at selbaie is done by qua-litative and quantitative examination of products collected at various points along the circuit. Causes of such problems as excessive loss of metals to the tailings or inefficient recovery of individual metals, can often be identified and possible solutions proposed.

Jan 1, 1989

By Esperidiana A. B. Moura, Célio H. Wataya, Roberta A. Lima, Rene R. Oliveira

The purpose of this study was to investigate the mechanical, morphological and thermal properties of biodegradable composites based on aliphatic-aromatic copolyester/polylatic acid blends (PBAT/PLA blends) reinforced by açaí seed fibers, an abundant byproduct of the açaí fruit agro industry. The biodegradable polymeric composites were prepared by melting extrusion process using a twin-screw extruder machine. The fibers removed from the açaí seed were used as the reinforcement and PBAT/PLA blends as the matrix. The influence of the açaí seed fibers addition on properties of composites was investigated by tensile and impact tests, SEM, DSC, and XRD analysis. Correlation between properties was discussed. In addition, açaí seed fibers characterization by SEM, XRD and WDXRF have also been carried out. The addition of açaí seed fibers on biodegradable PBAT/PLA blends showed that it is possible to get interesting property gains in biodegradable polymer by using waste from renewable sources.

Jan 1, 2015

By Åke Saudström

An EAF dust sample generated in a scrap based steel mill was treated by a combination of hydro- and pyrometallurgial techniques. The EAF dust contained mainly ferritic spinels forming solid solution phases according to the general chemical formula (MnxZnyFe1-x-y)Fe2O4 and other oxide phases such as ZuO. CaO and Ca2Fe2O5. The EAF dust was first treated by hydrochloric acid leaching at p8=3 which dissolved 63% of the zinc. The pyrometallurgical treatment of the leaching residue was studied using an induction heating system to simulate some important operations of EAF smelting of the residue in combination with steelmaking. The leaching residue was mixed with carbon powder to obtain a mixture with 52.1% ZnFe2O4 and 175% carbon. The mixture, scrap, and slag former were charged together in a crucible and heated to attain a melt temperature around 1650°C. The effects of different amounts of mixture on the zinc balance and iron recovery were examined. Based on the test results, suggestions are made for the EAF recycling procedure of the leaching residue.

Jan 1, 2003

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By G. Kyle Green

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the U.S. Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility.

Jan 1, 1995

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"Abstract: In this work, low temperature carbothermic reduction of Panzhihua low grade ilmenite after ball milling were investigated. The ball milling of ilmenite and graphite were processed in a ball mill. The milling process can attenuate the particle of ilmenite, and the ilmenite characteristic peak were broadened and weakened. The reduction temperature and behaviors are studied on the thermo gravimetric apparatus; lower temperature and higher reaction rate were obtained for the reduction of ilmenite with graphite after milled. The reduction temperature and times of ilmenite decreased to 1000-1025°C and 40-60min via milled for 4 or 8h; Low down the reduction temperature can eliminate the solution of Mg2+ and FeTi03 in a certain degree; the reduced ilmenite has an obvious loose structure, can favored the subsequent procedure such as leaching.1 IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposited in Panzhihua, China. In this reserve, there is about 8.73x108 t ofTi02, Accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [JJ Titanium mineral deposits major classified into Rock type and Placer type. Rock type is the igneous mineral, which have great content of FeO (Relative to Fe20 3) and gangue. The rock textures are compact and almost are complex ore. Rock type Titanium mineral major are ilmenite and titan magnetite ore, difficult to separate the metal ore and gangue. l.21 Thus, the Ti02 grade of Rock type ilmenite much lower than the Placer type (Table land 11). Panzhihua ilmenite are the typical Rock-type, due to the higher contents of MgO, CaO and Si02 and the complex mineralogy in ilmenite in Panzhihua region, making its direct reduction progressively more difficult. Mechanical activation, usually carried out by energetic milling or ball milling, was reported to significantly decreased the reduction temperature and accelerate the reaction rate of reduction of ilmenite with carbon, silicon and Magnesium. f3·(>J It reported that the process temperature were decreased to 600-1000°C and the annealing time were reduced to 30-120min after milled for 50-400 h. Shorter milling time involved was imported for else procedure such as direct leaching. 171 Hardly any research had referred to the carbothermic reduction reactivity of ilmeite milled for a short time as 1-1 Oh. In the present work, the aim is to investigate the reactivity and reaction temperature of carbothermic reduction of Panzhihua ilmenite. The Phase composition and micro morphology of samples are characterized."

Jan 1, 2011

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By Xueming Lv

The rotary kiln-electric furnace (RKEF) process is the main method for producing ferronickel from nickel laterite ore. However, this process is energy intensive as it involves several high temperature steps. Therefore, a novel process is proposed to directly produce ferronickel from nickel laterite ore by semi-molten reduction, which is expected to be realized in a rotary hearth furnace (RHF). The RHF process is able to shorten the flow sheet, decrease the reaction temperature as well as reduce energy consumption. In this study, the influence of basicity on reduction of nickel laterite ore was investigated. The results showed that it is possible to produce the ferronickel nugget directly at 1400 °C when the quaternary basicity [(mCaO + mMgO)/(mSiO2 + mAl2O3)] was fixed at 0.60. Under this experimental condition, the grade and the recovery ratio of nickel reached 11.53% and 98.59%, and the grade and recovery ratio of Fe were 84.16% and 68.72%, respectively.

By Thomas Gliick, Jianming Lu, David Dreisinger

"The recovery of manganese from the Boleo project of Baja Mining is via an acid oxidation and acid reduction process in seawater. Manganese as manganese dioxide is leached into solution as manganese sulphate with the addition of sulphur dioxide gas as a reductant and then precipitated as a manganese carbonate. The use of the manganese carbonate intermediate to produce electrolytic manganese metal (EMM) has been extensively studied. The manganese carbonate can be used in place of natural (MnC03) or reduced ores (MnO) of manganese as a feed to the EMM plant. Manganese carbonate can be dissolved in spent electrolyte from manganese plating, followed by purification using ammonium sulphide precipitation of minor elements and then electrowinning in a selenium free process. The results of small cell testing of manganese electrowinning are reported.IntroductionThe Boleo Project of Baja Mining is a greenfields development currently under construction approximately 5 km north of the town of Santa Rosalia, Baja California Sur, Mexico. The Boleo property is held by the Mexican company, Minera y Metalurgica del Boleo S.A. de C. V. (MMB). MMB is owned 70% by Baja Mining Corp. and 30% by a consortium of Korean companies consisting of KORES - Korea Resources Corporation, LS Nikko Copper, Hyundai Hysco, SK Networks and lljin Copper.The Boleo deposit has Measured and Indicated resources of264.7 million tonnes grading 1.50% copper equivalent (CuEq) & Inferred resources of 159.9 million tonnes grading 1.15% CuEq. The calculation of copper equivalent is based on a combination of metal prices and predicted metallurgical recoveries (Table I). The metallurgical recoveries have been confined by extensive bench and pilot plant testing. Proven and probable reserves are available at Boleo to provide for more than a 30 year mine life. Initially, 25 years of mine life and 23 years of process plant operation have been scheduled in the February 2010 Technical Report Update (www.sedar.com)"

Jan 1, 2012

By Takeo Fujino, Nobuaki Sato, Yarong Wang, Kohta Yamada

"Ternary mixed sulfides of some transition metals MTS3 (M=Ba, ·Pb, T=Ti, Zr) were synthesized by a relatively low temperature process using sulfur melt. The mixture of starting materials, such as, metals and/or binary sulfides and a large excess of sulfur was reacted in a vacuum-sealed Pyrex or quartz ampoule at 350- 600 °C for one to three weeks. After the reaction, the remaining sulfur was completely removed by a process composed of filtration of sulfur melt and followed dissolution in CS2• The binary sulfides impurities coexisted in the products were removed by rinsing the products in water and acetone. By using the above method, BaTiS3, PbTiS3 and BaZrS3 'Were obtained in pure form. The effect of addition of halides on the yields of these ternary sulfides were also discussed.IntroductionThere have been a vast number of studies on the preparation and physical and /or chemical properties of mixed metal oxides. As is well known, some of such compounds exhibit excellent materials properties, causing them for use in mechanical, electronic, magnetic and chemical devices. Not a few mixed metal sulfides show similar physico-chemical properties to those of the corresponding mixed metal oxides. However, the study of the mixed sulfide crystals is rather sparse mainly due to difficulties in preparing these compounds. In various methods which have been adopted for preparing mixed sulfides, the simplest method would be the solid-solid reaction of the component binary sulfides or elements. However, there are always diffusional constraints with regard to the reactions in solid phases causing it necessary to heat the reactants at sufficiently high temperatures, viz. 800-1200°C. On the other hand, some mixed sulfides are unstable at high temperatures or to change their materials properties due to sulfur nonstoichiometry and structural modification depending on temperature, i.e., synthesis of such compounds needs to be made at lower temperatures. Processing in alkali halide melts is hopeful to overcome the above problems but to obtain the halide melts the temperatures above ~ 600 °C is needed. Low temperature reaction has been carried out for the preparation of Hg1.24TiS4, which was formed by the ·combination of TiS2 and molten Hg metal at 320°C[l]. Reaction of WS2 with LiBH4 melt at 350°C yielded LixWS2[2]. These sophisticated methods, however, can be applied only to the vary special cases."

Jan 1, 2000

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003