Search Documents

By Dianyuan Dang, Guihong Han, Wenjuan Wang, Tao Jiang, Yanfang Huang

In this study reduction kinetics and swelling behaviors in "two-step process” were investigated by weight-loss technique and visualizing physical changes of pellet. Results showed that reduction degree (r) increased with increasing temperature and time. According to the dynamic calculation, when reduction temperature was lower than 1000°C the reduction process was controlled by chemical reaction with apparent activation energy of 72.27 kJ/mol. When reduction temperature was higher than 1000 , the equation of t/[1-(1-r)1/3] against [1+2(1-r)-3(1-r)2/3]/[1-(1-r)1/3] followed straight lines, demonstrating that reduction was mixed-controlled. Swelling experiments indicated that the maximum swelling index increased with the increase of reduction temperature and CO content.

Jan 1, 2016

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Tracy Lucas, Ian Hamill

"Issues of importance in the area of continuous casting centre around product quality. This can be affected by particle inclusions transported into the mould from upstream processes and by draw-down of particles from the meniscus. Turbulence of the meniscus can increase the latter and is also detrimental to product surface quality.Suitably validated Computational Fluid Dynamics (CFD) modelling can provide the operator with an efficient tool with which to investigate the effects of changes to the design and operation of the caster and associated plant.In this paper, examples are presented of the use of the CFD software, CFX, to simulate:•,free-surface shape and turbulence in the mould using deforming meshes•,solidification in the mould using a fixed-grid, source-based method•,argon gas injection through a submerged entry nozzle using a full multiphase model•,inclusion motion and removal in tundishes using an algebraic slip model.The CFD simulations of the free surface shape are complemented by detailed Particle Image Velocimetry measurements performed on a full-size water model of a thin-slab mould and upper strand. Close agreement is demonstrated between the predictions and experiments."

Jan 1, 1999

By Kim Verbeken, Evelien Van de Steene, Marc Verhaege, Jeriffa De Clercq

"AbstractThe industry is confronted with stricter discharge levels and an increasing awareness to avoid toxic waste (such as heavy metal containing sludge obtained in physicochemical water treatment) and recover valuable metals. This can be realized by ion exchange or by electrodeposition. Both techniques however show an optimum concentration range to efficiently remove and/or recover metals: electrolysis can recover the metal in its metallic form but suffers from low efficiency when applied to diluted solutions, whereas ion exchange can only be applied economically in the low ppm range.A combination of ion exchange followed by electrodeposition was applied to an industrial wastewater. The strong acidic ion exchange resin was stripped with H2SO4 giving a solution of 9g/L nickel. From this solution, nickel was electrodeposited in an ammonia buffer on a Ti-mesh cathode with high current efficiency. It is shown that organic compounds (surfactants, brighteners, …) present in the industrial wastewater do not influence the recovery process.IntroductionAlmost all rinse waters emerging from metal plating plants are generated during the washing operation of plated materials. These solutions with low metal content must either be recycled within the process or be discarded to the surface water after decreasing their metal content to acceptable levels determined by the local environmental regulations, which become more and more stringent. Today, the most commonly used practice is a physico-chemical treatment (precipitation) and a resin post treatment to meet the standards. A more sustainable approach should use a technology to recover efficiently the metal or metal salt without the production of sludge and the effluent should be consistent with environmental regulations."

Jan 1, 2008

By Baozhong Ma, Yonglu Zhang, Yongqiang Yang, Chengyan Wang, Yongqiang Chen

During the past decades, slurry electrolysis (SE) has been implemented commercially for the processing of bismuthinite and complex Pb-Cu bearing gold concentrates. Recently, SE was proven effective for the treatment of As-rich antimonic gold concentrates. Laboratory test results suggest over 98% of the antimony was extracted, while the extraction of arsenic and gold was less than 0.5%, and that of iron was less than 6%. Moreover, the cathode antimony contained over 98% antimony and less than 0.3% arsenic. Considering the disadvantages of traditional 3 kA slurry electrolysis baths, such as smaller electrode area, reduced capacity, and greater electrode deterioration, the authors have developed an innovative 12 kA slurry electrolysis bath equipped with mesh and fence type titanium alloy electrodes. Furthermore, the technique was successfully used within a pilot scale plant yielding results similar to those observed in the laboratory. The technique yielded ametallic antimony ingot of 99.9% purity after arsenic removal via the addition of Na2CO3.

Jan 1, 2014

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By Alessandro Blasi, Massimo Morgana, Corradino Sposato, Pietro Garzone, Giuseppe Devincenzis

A comparison among (2-ethylhexyl)-mono (2-ethylhexyl) ester Phosphonic acid (P507), Secondary-octyl phenoxy acetic acid (CA-12) and Bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex272), in heavy rare earths separation via hydrometallurgical processes has been investigated. The separation coefficients, , were obtained and the extraction selectivity has been evaluated using a mixture of heavy rare earths from Samarium to Ytterbium. The experimental results indicated that P507 and Cyanex 272 display a greater affinity for heavier rare earths while CA12 proved to be more effective for the lighter rare earth metals.

Jan 1, 2014

By Peng Jianping, Feng Naixiang, Di Yuezhong, Wang Yaowu, Pan Xijuan

A vacuum silicon thermal reduction lithium process is developed in present work which used lithium hydroxide, alumina and calcium oxide as raw materials. The process contains two steps, which are that Li5AlO4 clinker is prepared in ambient environment, and that metal lithium is extracted from Li5AlO4 clinker with ferro-silicon alloy as reductant in vacuum. On the basis of thermodynamic analysis and investigative experiments, feasibility of this process is proved. The results show that Li5AlO4 can be generated by calcination lithium hydroxide and alumina, the burning loss is above 31% under the conditions of calicination temperature above 750℃ and time more than 90min. The main phases of calcination product are Li5AlO4 and CaO. When the calcination product is reduced by ferro-silicon alloy in vacuum, the lithium reduction ratio can be over 80% under the conditions of reduction temperature 1200℃ and reduction time 60min.

Jan 1, 2014

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Shufang Ding, Fukun Yan, Zhiqiang Shan, Wei Chen, Cuicui Ji

"To remove aluminum ion from chlorinated rare earth solution, this paper used hydrolysis method to explore the hydrolysis behavior of aluminum ion in aluminum chloride solution and confirm the optimum conditions of aluminum ion hydrolysis, which are pH value, temperature and initial concentration of Al203 and so on. The experimental results show that single treatment can make aluminum precipitation rates of chlorinated rare earth solution reach about 90% by hydrolysis precipitation; and then several recycle disposal can get precipitation rates of 89% for aluminum and 2.86% for rare earth.IntroductionIn China, rare earth resources are very rich and unique minerals, complete variety, and rare earth products are very large in the domestic reserves. Rare-earth and application products have been deep into all areas of our life, permanent magnet material of rare earth is one of the most popular application areas[11. Binary oxides such as praseodymium neodymium have been widely applied in the fields of glass, ceramics, magnetic materials, catalysts and so on. Especially, the advent of the Pr-Nd-Fe-B magnets which makes the world magnetic material into a new stage of development [2•3]With the development of science and technology, for industrial, physical and chemical indicators of raw materials Pr-Nd oxides (such as particle size, specific surface area and non rare earth impurities etc.) are also getting higher and higher. The oxide size has an important influence on sludge formation in the electrolytic process. If the size is too large, added oxides have settled on the bottom of slot before melting, and then generated sludge; if the particle is too small, it can cause dust dispersion, enlarge oxide unit consumption and increase the cost of production in the charging process. Some early processes use oxalic acid to make chloride neodymium praseodymium settle, and impurity can be removed cleanly, but the cost is high, it is not suitable for production. At present, most enterprises are using ammonium hydrogen carbonate to precipitate chlorinated neodymium praseodymium, but chlorinated neodymium praseodymium such as iron and aluminum and so on can easily form gel in the precipitation process, seriously affect the growth of neodymium praseodymium carbonate crystal and often leads to particle meticulous, even may also generate gel-like neodymium praseodymium sediments and cause centrifugal or suction filtration difficult. Now the actions and their removal of impurity such as iron and aluminum have done a lot of research in the production process of rare earth, removing aluminum craft with alkaline (sodium hydroxide) and acid (oxalic acid) has good effect, but the cost is higher[41; used adding complex agent to remove aluminum method which is simple and easy to operate, but aluminum removal rate is not high, and also changed the sediment of crystal type[51, and etc. This paper discusses the removal of chlorine from rare earth solution on the basis of the hydrolysis property differences betweenAJ3+ and rare earth ion."

Jan 1, 2013

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By H. V. R. von Rhaden

Systematic quantitative X-ray diffraction analyses performed on diamond-drill cores originating from the Aandenk formation at the Loraine Gold Mine, located in the Welkom goldfield, Orange Free State, South Africa, have revealed the presence of a number of phyllosilicate mineral assemblages which have not hitherto been reported from this region. Rectorite, a regularly interstratified 1:1 mica-montmorillonite "swelling clay", is found to occur together with paragonite, muscovite, pyrophyllite, kaolinite, and chlorite in highly-altered friable rocks. The presence of rectorite in mill feeds may have potentially serious implications with respect to gold recovery. Quantitative X-ray diffraction analysis for phyllosilicates can be used as an aid to correlation, and also to guide the widths of stopes in underground mining. Rectorite has a unique mode of origin, which is discussed.

Jan 1, 1991

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By Tam Tran

Over the last decade, halide (chloride, bromide and iodide) systems have been evaluated as alternative lixiviants for the processing of gold to replace cyanidation which has been widely used in commercial practice. This paper first reviews the development of processes promoted by Kaljas Ltd / Lachlan Resources (Australia) and Great Lakes Corp (USA) using different bromide/bromine systems in the early 1990's. Several research groups subsequently evaluated the use of iodide/iodine and chloride/chlorine for gold extraction, showing similar characteristics of gold/silver dissolution and recovery. A critique is :given on the advantages and the ,shortfalls of halide systems as alternative lixiviants. The stability of gold? halide complexes is discussed, based on practical experience and thermodynamic modelling of their speciation, The iodide system provides the most stable gold / silver complex for easier handling. However, the cost of iodide inhibits its application for are processing. In this critique, emphasis is given on the cheapest system, which involves the use of chloride for leaching (in conjunction with an appropriate oxidant). However the chloride-base leachant has a major drawback which is related to the unstable nature of gold chloride in a reducing environment.

Jan 1, 1998

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991