Search Documents

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Edilson Marques Magalhães, Danielly Da Silva Quaresma, José Antônio da Silva Souza, João Nazareno Nonato Quaresma, Emanuel Negrão Macêdo

"The production of alumina from bauxite using the Bayer process generates the residue known by red mud. This material can be used as a source for concentration and recovery of valuable metals such as titanium. The greatest difficulty of concentrating titanium compounds is the large amount of iron oxide present in red mud > 30% by weight. This paper shows the extraction of the iron oxide, increasing the concentration of the titanium compounds. The red mud is leached with H2SO4 at 30% concentration and temperature range of 60°C, 80°C and 90°C. Analysis of the leached and concentrated was made to verify the effectiveness of the iron oxide extracting process and the titanium compounds concentration viability.2- IntroductionIn the state of Para is located the Industrial Unit Alumina of North of the Brazil S/A (Alunorte), created to produce and commercialize alumina, aluminum oxide, Al2O3. The ALUNORTE with Aluminum Brasileiro S/A (Albras) and Mining Rio do Norte S/A (MRN) complete the production cycle of aluminum in the state. Although the production of alumina has a importance great for the socio-economic status, as in any area other, generates a amount large of waste, thus causing environmental impacts. Pará State has produced 25 million tons of bauxite (Pinto, 2010), of which 60% were transformed into alumina plant in Pará and Maranhão by ALUNORTE by ALCOA, generating approximately 9,000,000 tons of waste known as Red Mud (RM). Due to the high reactivity this material is considered dangerous, and currently there is no operating process capable of reuse all the material produced at any refinery. The search for industrial processes in order to reuse these wastes can contribute to reducing the overall impact of the production process of alumina. In this context, this paper estudied, within the research line of Solid Waste valorization the mining industry and metallurgy, a process that makes possible the red mud as a source of raw material, in other words, seeks to maximize the use of red mud as raw material for concentration and or recovery of titanium compounds in both the crystalline form of anatase, rutile and ilmenite, avoiding the predatory extraction of natural resources of these materials. Applying definitely the concept of self-sustainability of the mining industry and metallurgy."

Jan 1, 2012

By V. M. Sokolov, Jr. DuPlessis

The technology for recycling fine wastes, grinding sludges or swarf, and solids such as slag that contain a high content of metallic material needed improving. The objective was to produce a master alloy that met the tight requirements of the Western manufacturers and achieve improved yields of the valuable elements, nickel and cobalt, to over 90%. The alloys from the production of Alnico. magnets were chosen for this work. A process is proposed .that is able to recycle all kinds of Alnico wastes. This process is able to reduce all detrimental elements, which are contained in the wastes, to within acceptable levels. Molybdenum, if present, is an exception. Depending on the levels of contamination of undesirable elements different recycling strategies are proposed. The majority of the wastes can be recycled by melting and refining with a liquid slag layer using unique melting furnaces that are relatively unknown in Western nations. The proposed technologies allow the reelamation of over 95% of the cobalt and nickel from any kind of Alnico waste, and there are no limitations on the proportion of different kinds of wastes in the charge. The proposed processes and technologies could also be applied to the recycling of grindings, turnin

Jan 1, 2000

By Ehsan Vahidi, Fereshteh Rashchi, Ataollah Babakhani, Alireza Zakeri

"The synergistic effect of Cyanex 302 on solvent extraction of nickel and cadmium from sulfate solution with D2EHPA diluted in kerosene was investigated with the aim of increasing separation efficiency. Experiments were carried out within a pH range of 0.1-5.0 using sole D2EHPA and D2EHPA-Cyanex 302 mixtures in different ratios. Increasing Cyanex 302 to D2EHPA ratios in the organic phase caused a left shifting of the extraction isotherm of cadmium and a right shifting of the extraction isotherm of nickel. As a result, optimum separation was found with a Cyanex 302 to D2EHPA ratio of 0.1M:0.5M. In the present system, effect of a modifying reagent such as TBP was studied. The influence of various diluents including kerosene and carbon tetrachloride was also investigated.IntroductionBatteries are popular sources of portable energy. Ni-Cd batteries are manufactured in two main groups of small domestic cells and large industrial batteries with 80% being in domestic use. Ni-Cd cells have various uses, for example in cordless electric utensils, cordless telephones, airplane engine starters, and communicational distribution systems [1].Depleted Ni-Cd batteries are classified as hazardous waste since nickel and cadmium are heavy metals and suspected carcinogens. Given the risk associated with uncontrolled disposal, directions for issuing legislation on disposal and recycling of used batteries have been made in industrialized countries [2]. Recycling of Ni-Cd batteries is important from both economic and environmental points of view. Different methods have been used for recycling these wastes through pyrometallurgy [3], biotechnology [4,5], and hydrometallurgy [1,2].Due to the advantages of hydrometallurgical processes, several studies have been implemented on leaching and solvent extraction (SX) of the used Ni-Cd batteries. Leaching of batteries is usually done in sulfate or chloride media; while solvent extraction has been used in different extractants: two-stage solvent extraction by D2EHPA and Cyanex 272 [6]. Solvent extraction of Cd from leach solutions has been studied using various extractants; Cyanex 301 [1], D2EHPA [7], Cyanex 302 [8], Cyanex 923 [9], Cyanex 272, Tops 99, PC88A [10]. Application of phosphorus based extractants for the solvent extraction studies of Ni such as TOPS 99 [11], D2EHPA [12], Cyanex 272 [2], has been investigated. Separation of Cd(ll), Ni(II), and Co(ll) from chloride leach liquor of spent batteries [13], were explored in the earlier studies. Cd extraction with D2EHPA involves co-extraction of both Ni and Co [14], which causes issues in the separation process efficiency."

Jan 1, 2012

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By Hui Zhang

The leaching behavior of palladium powder in aqueous solutions containing NaCI or N&apos;H4Cl was investigated. Cupric ion was used as an oxidant for the dissolution reaction. The effect of a number of leaching parameters such as temperature, concentration, stirring speed and surface area on the leaching rate was studied. The leaching system containing chloride and cupric ion was found to be very effective for the dissolution of metallic palladium. Based on the experimental results the overall leaching rate was believed to be controlled by a chemical reaction step. The dissolution rate of palladium was found to be first order with respect to the concentration of cupric ion and second order with respect to the concentration of chloride.

Jan 1, 1996

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the effect of inoculums volume on bioleaching to recover metals from printed circuit boards using Acidithiobacillus ferrooxidans-LR. Printed circuit boards from obsolete computers were mechanically processed by comminution followed by magnetic separation, and the obtained non-magnetic fraction was used in the bioleaching experiments. A shake-flask study was carried out on the non-magnetic fraction samples using a rotary shaker at 30°C, 170 rpm and different volumes of oxidized culture solution as inoculums (%v/v): 5, 10, 20, 30, 40, 50 e 60. The oxidized culture solution was prepared inoculating pre-adapted bacteria Acidithiobacillus ferrooxidans-LR (5%v/v) in 200mL T&K medium. Leaching in acidic ferric sulphate was also performerd. The analyzed parameters were pH, ferrous iron concentration and metals analysis (AAS). The results showed that using 10%v/v of inoculums were extracted 99,2% of copper and 60% of aluminum by bioleaching. Zinc, lead and tin extraction were not influenced by bacterial leaching and extractions rate were obtained by chemical leaching promoted by acid medium. Ferric iron leaching extracted less copper (35%) than bioleaching. SEM analysis shown surface difference between samples of non-magnetic fraction before treatment and after bioleaching, showing corrosion pits formed by the bacteria contact.IntroductionWaste of electrical and electronic equipments (WEEE) has been target of discussion due to environmental, political and economical issues involved. Around 17 million of computers are discarded annually in the world due to malfunctioning equipment or because technologies become obsolete [1,2]. In contrast, only the central processing unit (CPU) of computers weights around 3kg. From this data, it can be calculated that 51 million kilograms of CPU waste are discarded yearly. This calculation was performed considering only the CPUs, disregarding the cathode ray tubes and liquid crystal displays of monitors [3,4]. Because of the amount that has been accumulated, e-waste has become a global problem but also can be an alternative source to recover valuable materials [5,6]."

Jan 1, 2012

By Y. Ono

In lightweight metal processing such as aluminum (AI) and magnesium (Mg), metal cleanliness is a crucial process parameter for refining, part manufacturing and recycling in order to obtain high quality parts and products. In this paper, techniques for cleanliness evaluation of molten AI and Mg using ultrasonic probes with clad steel buffer rods having high signal-to-noise ratio (SNR) are presented. Due to the high SNR of the ultrasonic probes used, backscattered ultrasonic signals from inclusions, which may be oxide films and/or particles, in molten Mg and those from silicon carbide particles, having an average size of 50f.Ull, added in molten AI are successfully detected with reflection configurations of pulse-echo and/or pitch-catch modes at an ultrasonic frequency of 10 MHz. In addition, relative cleanliness evaluation of molten Al and Mg is demonstrated. In order to establish the procedure and to investigate the optimum system configurations for cleanliness evaluation of molten metals, particle flow simulation system using water and polyvinyl chloride (PVC) particles has been constructed. Counting the number and measuring the size distribution of the PVC particles, having an average diameter of 128um, suspended in water with the PVC volume concentrations of 5ppm and 10ppm are performed with ultrasonic pitch-catch mode. The counted numbers of particles by the presented method and system have good agreement with the calculated results with a count error of less than 10% or two counts. Based on the results obtained with water simulation experiments, the prototype system for cleanliness evaluation of molten Mg by counting and sizing inclusions has been developed. Keywords: Ultrasound, Clad buffer rod, Molten metal, Aluminum, Magnesium, Inclusion detection, Cleanliness measurement, Counting, Sizing

Jan 1, 2003

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By Matthias Merzkirch, Volker Schulze, Kay Andre Weidenmann

"Unidirectionally reinforced light weight compounds based on light metals such as the aluminium alloy EN A W-6082 are adequate materials for the future use in transportation means like automobiles and airplanes. Due to the occurring cyclic loads knowledge about the crack growth behaviour of such composites is needed. The investigations at a load ratio of R = 0.18 show that the crack growth rate of the aluminium matrix is reduced if reinforced by spring steel wire with a reinforcing ratio of only about 1 Vol.-%. Additionally, the acoustic emission analysis allows detecting crack growth within the matrix material, crack propagation along the interface wire/matrix and crack closure which could also be determined with the help of a self designed capacitive displacement measuring gauge. The damage behaviour could be verified by metallographic and SEM investigations.IntroductionIn the field of lightweight structures for transportation means the need for light, strong and stiff materials, in particular composite materials, is increasing in order to save resources and costs. Lightweight materials such as aluminium and magnesium alloys are highly efficient candidates to be used in the composite extrusion process [1] which allows for a simple production of unidirectionally reinforced profiles with a large diversity of geometries at low costs. Figure 1 depicts the principle of the composite extrusion process; within the first part of the tool the billet material is split into several strands whereas the middle part of the tool allows the supply of the reinforcing elements. The third part of the tool rejoins the matrix material and the reinforcing elements and defines the final shape of the profile."

Jan 1, 2011

By Hyun Soo Kim, Joon Soo Kim, Myong Jun Kim, Jyothi Rajesh Kumar, Jin-Young Lee

Rare earth materials have an ever growing variety of applications in the modern and hitech technology. They apply to many an industry with crucial materials and they provide numerous a customers with benefits. Rare earth materials utilization increasing day-by-day in the worldwide, at the same time the resources is very limited in many countries like Korea. The present general article divided four sorts such as 1) mineral processing of Korean ore deals the gravity, magnetic separation and froth flotation, 2) decomposition and leaching of concentrates included sodium hydroxide fritting, sodium hydroxide hot digestion, hydrochloric acid leaching, 3) separation and purification of rare earth elements in mixed rare earth chloride solution consists reduction and oxidation method, solvent extraction, 4) preparation of rare earth oxide compound from purified elemental rare earth chloride solution having oxalate salt precipitation by reaction crystallization. The last part consists of a summary of the present study.

Jan 1, 2015

By Takeshi Ohgai, Hisaaki Fukushima, Tetsuya Akiyama, Joon-Seo Ki

"Recently, an intensive attention has been paid to the electrodeposition of Zn-Cr alloy in the field of the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation. In this study the electrodeposition of Zn-Cr alloys from the sulfate baths was conducted to investigate the codeposition mechanism of Cr with Zn. As a result, Cr was codeposited with Zn at higher current densities in both polyethyleneglycol(PEG)-free and PEG- containing baths. However, PEG made it possible to reduce Cr+ to the metallic state and Cr existed in the form of Cr(III) hydroxide in the deposits obtained from PEG-free bath. The measurements of the partial polarization curve of Zn and the pH in the cathode layer revealed that PEG acted as a polarizer to shift the cathode potential to the reduction potential of the composited hydroxides of Zn and Cr formed due to the pH rise in the cathode layer.1. IntroductionRecently, much attention has been paid to the electrodeposition of Zn-Cr alloys because of its application to the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation1Hl_ Some researches have already tried to commercialize this type of steel sheet. High corrosion-resistance of this steel sheet is brought about by codeposited Cr in the alloys. According to Piontelli's classification5l concerned with metal deposition from aqueous solution, Cr belong; to an inert metal and its deposition is associated with a large amount of hydrogen evolution. Therefore the current efficiency for Cr deposition is extremely poor. It has been also reported that Cr is unable to codeposit in the electrodeposited Zn film in the absence of a certain additive in the solution. 0-compounds group colloids7l, ether group organic compounds8), 9>, peptide based compounds10l, etc., have been found to be effective additives to induce the codeposition of Cr with Zn. However, few studies have been made on the codeposition mechanism of Cr with Zn. In this research, the fundamental electrodeposition behavior of Zn-Cr alloys from sulfate baths was investigated to clarify the codeposition mechanism."

Jan 1, 1998

By Kazuhiro Asai

Hitachi Refinery of Nippon Mining & Metals Co., Ltd. installed a reverberatory type recycling fumace in 1978 in order to treat the industrial wastes which contain metal elements such as copper, gold and silver. Pyrite and industrial waste materials such as galvanizing sludge, hydroxide slime and dust are smelted. Sulfidized copper, iron and precious metals are transformed into matte and other metallic elements are oxidized into slag This copper matte is transported to Saganoseki smelter and copper and precious metals in the matte are recovered. Recently it is difficult to obtain pyrite economically because of the decrease of pyrite production. Therefore, a new treating process of the liquid waste has been investigated at Hitachi Refinery. In this process, the sulfide or sulfate from the liquid waste are smelted as a source of sulfur.

Jan 1, 1997

By Yong-ming Chen, Chao-bo Tang, Yun Li, Long-gang Ye, Sheng-hai Yang, Hao-tian Xue

In order to achieve high recovery of Cu and Co during cobalt-bearing copper sulphide ore smelting process, reducing agent (coke) and sulphidizing agent (pyrite) were added into molten smelter slag for reducing-sulphidizing smelting to product Cu-Co matte. Effects of reductive atmosphere, pyrite dosage, smelting temperature and smelting duration on Cu, Co, Fe distribution behaviours were investigated. The results show that the distributions of Cu and Co are mainly enriched in Cu-Co matte, and the distribution ratio, LCu and LCo, improve with increasing of coke amount or pyrite addition, whereas above 6 wt.% coke or 20 wt.% pyrite, Cu and Co tend to transfer from matte to cleaned slag. A properly high temperature(1300) and smelting duration(3h) are beneficial to the enhancement of the distribution ratio of valuable metals, and under the given set of conditions, LCu > LCo generally. However, an undesired high Fe contents in matte limit further increase of LCu and LCo.

Jan 1, 2015

By Alan Branham

The Mike deposit is a large, low grade, oxide, gold-copper system found at the intersection of two major faults that bound the Carlin Window, Eureka County, Nevada. Disseminated gold occurs within metamorphosed and hydrothermally altered silty limestone (Silurian-Devonian Roberts Mountains Formation), beneath 182 m (600 feet) of barren Tertiary sediments and tuffs. A supergene copper oxide blanket occurs beneath and locally overlaps the lower portion of the gold zone. Decalcification argillization, silicification, and brecciation are superimposed on earlier calcsilicate hornfels and marbles. Altered dikes and sills intrude the gold zone and are locally auriferous.

Jan 1, 1995

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993