Search Documents

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By Wen-Ming Chien

Low temperature X-ray diffraction and thermal property studies of the solid-solid state phase transition for the polyalcohols (pentaerythritol (PE), pentaglycerine (PG) and neopentylglycol (NPG)) thermal energy storage solid solutions have been investigated by using X-ray diffractometry and differential scanning calorimetry (DSC) methods. X-ray diffraction studies on polyalcohols solid solutions, PE-NPG and PG-NPG, are from ?10oC to 50oC. XRD results shows the + mixed phase at the related low temperature (?10oC) for both PE-NPG and PG-NPG solid solutions. At high temperature range, XRD results show phase for PG-NPG solid solution and + mixed phase for PE-NPG solid solution. There are only two Bragg peaks, (111) and (200), shown in phase XRD patterns. The polyalcohols solid solutions have been cycled 5 times between -20oC to 100oC at different DSC scan rates to study the phase transition properties. DSC results of both PE-NPG and PG-NPG solid solutions show that the solid-solid state phase transition is near room temperature. Details of low temperature phase transition XRD and DSC results of PE-NPG and PG-NPG solid solutions will be presented

Jan 1, 2006

At the present time, cyanide is the most widely used reagent to extract gold from its ores and concentrates. However, its use in mining has become the focus of intense attack by various groups throughout the world; as a consequence, a renewed effort has been launched to find suitable alternative lixiviants to recover gold. Chlorination was the most popular process to extract gold, before it was rendered obsolete with the advent of the cyanidation process at the turn of the last century, not least because it required the use of potentially hazardous and costly chlorine to oxidize/complex the gold. The PLASTOL® process, originally designed to recover the platinum group metals (PGM?s) from their ores and concentrates, provides an alternative to cyanide for gold ores. The process generates oxidizing conditions in the autoclave capable of forming the AuIII ion, and gold chloro-complexes result from the addition of small quantities (~5-10 g/L) of sodium chloride to the autoclave. The principles of the PLASTOL® process are briefly described, and several applications of the process to gold concentrates are presented. Various options available to recover gold from PLASTOL® leach solutions are also discussed.

Jan 1, 2003

By A. V. Tarasov

Emission of sulfur-containing gases causes most adverse impact on the natural environment in the process of nonferrous metals production. Under the conditions of Arctic regions, in particular in the region of the Norilsk Mining and Metallurgical Complex (Russia), this problem requires a special approach taking into account potential economic and socioeconomic consequences. By reducing the iron sulfide content of flotation concentrates by using new flotation reagents inhibiting pyrrhotite flotation and by applying advanced process flowsheets for flotation it is possible to increase the nonferrous metals content of flotation concentrates by 5% or more along with a corresponding reduction in SO2 formation during their subsequent pyrometallurgical processing. The ways used to resolve the environmental problems in the Norilsk region in the process of nickel and copper production, are based on the improvement of methods for elemental sulfur recovery from metallurgical off-gas by non-conventional techniques, the sulfur recovery from metallurgical gases by production of liquid sulfur dioxide and the technology for pyrometallurgical treatment of sulfide concentrates without SO2 formation. Another opportunity is the development and commercial introduction of hydrometallurgical technologies for treating copper-nickel sulfide ores.

Jan 1, 2006

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By M. Cross

Heap leaching presents a complex physico-chemical process to model and a significant challenge to develop a comprehensive model enabling reliable predictions of heap behavior over the long term. A computational modeling framework is described for the analysis of multi-phase flows in reactive porous media suitable for tracking metals recovery, for example, in heap leaching and environmental recovery processes. This modeling framework employs appropriately formulated, parameterized, and solution procedures to capture: 1) liquid and gas flow through heterogeneous porous media subject to variably saturated flow conditions, 2) the complex and dynamically changing nature of the porous media structure, 3) the transport of reactants and products of reaction, 4) the simultaneous mass and heat transfer, and 5) the role of bacteria as a catalyst for reactions. A second class of challenges to accurately model heap processes is to identify and then capture all the process data to characterize the reactivity of particular ores, the mine planning for the construction of the heap, leach schedules, meteorological data, etc. The objective of this paper is to outline these challenges and to describe a modeling framework that can cope with arbitrarily complex geometries and provide tools for rapid and accurate process assessment.

Jan 1, 2006

By Daniel S. Gwinner

The tolling, or processing for a fixed fee, of aluminum drosses to recover the metal units is a common practice in the Aluminum Industry. The Dross Toller is acting for the owner, and since most dross processes result in material going to landfill, it is important for the owner of the dross to insure that the toiler is processing the material and handling waste disposal in an environmentally responsible manner. The paper discusses the Dross Toiler Audit Program, first from the Reynolds Metals Company perspective. Included are the reasons the company deems it necessary to audit and a description of the items covered during the audit. Finally, there will be a discussion of the audit from the Tollers perspective - what the Toiler can expect when the auditor arrives.

Jan 1, 1995

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Wenying Liu

The effect of aeration on chalcocite heap leaching was studied by analyzing the historical data from two chalcocite heap leach pads located in Chile, one with aeration and the other without aeration. The data showed that the copper leaching kinetics of the aerated heap was greater than that of the unaerated heap within a certain leaching period, after which there was no effect of aeration on the copper leaching kinetics. The total acid consumption per ton of ore processed was higher in the case of aeration, which was supported by the higher pH of the PLS. But the net acid consumption per ton of copper produced was the same in the two cases. Approximately 5% of the total iron added to the unaerated heap was precipitated inside the heap. In contrast, there was no net iron precipitation or generation inside the aerated heap. Bacteria activities were thought to occur even in the unaerated heap, but the extent was much less than in the aerated heap. Given the importance of forced aeration in chalcocite heap bioleaching, mathematical modelling will be applied in the future work to assist the optimization of the aeration system design.

By S. Kawamura, H. Inoue, Y. Maeda, H. Ohike

Kosaka smelter is a copper smelter located in Akita Prefecture in the northern part of Japan. It has treated complex sulfide concentrates for a long time. Recently, in addition to metal production from ores, the company has been working on the recycling of metals by using this metallurgical technology. Metals recovered are primarily gold, silver, palladium, copper and lead from copper scraps, electronic board scraps, silver oxide batteries, spent lead acid batteries, semiconductor chips, cellular phones, and automotive emissions catalyst. In particular, electronic board scraps and cellular phones can be valuable raw materials. These electronic scraps are fed into the flash smelting furnace after size reduction in a shredder that was introduced in 1999. Due to the growing demand for personal computers and cellular phones, the amount of electronic board scraps available for recycling increased. At present, these secondary materials are good raw materials for Kosaka smelter since the smelter is already used to dealing with complex raw materials. The recycled metals account for up between 5 and 20 percent of the total production at Kosaka Smelter. In particular, over 90 percent of the palladium in the secondary materials can be recovered.

Jan 1, 2000

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Murray Hughes, Neil Brown, John Carran

"A control system architecture has been developed using the Ward-Mellor structured analysis techniques for real-time applications. This approach has produced several advantages over traditional control system implementation methods including:•,partitioning of the control system into discrete control functions.•,easy identification of the interaction between individual control functions and the rest of the system including the impact of changes at the control system boundary (i.e. additional inputs or outputs).•,simplified control software testing.•,a closed loop design, implementation and documentation process.This paper describes a generic control application in which the process specification and control system design are logically linked. Both components are used by process engineers for on-going development.IntroductionAluminium is reduced from alumina in multiple electrochemical semi-batch reactors. Raw material additions and molten metal withdrawal are made at discrete intervals ranging from seconds to days. The electrolytic reduction process is continuous, despite the semi-batch nature of the material inputs and outputs. The chemical and physical processes that occur within each reactor are complex and interdependent, therefore simple methods used for the control of many chemical processes are impractical. The process control system is required to optimise operating efficiencies within the safe operating zone.The process control of aluminium reduction cells is heavily biased towards calculation of process variables with relatively few measured sensors. Each cell is controlled independently of the other cells, although changes to process conditions and raw material . quality will affect all cells. The process responds relatively slowly and with significant time lags. Measurements and process variable calculations occur each second, however the accuracy and precision of actuator response and sensor sampling are measured 111 milliseconds. Time-based scheduling is a significant component of reduction cell control."

Jan 1, 1994

By A. V. Tarasov

The nonferrous metals industry has been a sector with one of the highest growth rates during the recent years. The prospects for the Russian metals industry during the period until 2010 are associated first of all with a growing domestic demand for its products. The technological level of the metallurgical operations in Russia is relatively low in comparison with industrially developed countries: the average energy requirement is higher by 20% to 30%; the amount of generated waste in the process of rolled products manufacture is twice as high; the average labor productivity is lower by 2.5 to 3.0 times; the overall negative environmental impact is twice as high. Improvement of the technological level of the nonferrous metals production under the conditions of market economy is possible by application of innovative technologies for the development of this sector. The main trends for development of the nonferrous metals sector are: - meeting of more stringent requirements to the quality of concentrates; - more complete recovery of associated elements as commercial-grade products; - development of continuous process lines based on autogenous, resource-saving and environmentally safe processes; - use of combined technologies, including pyrometallurgical, hydrometallurgical and upgrading processes; - expansion of the fields of application for nonferrous metals and their alloys.

Jan 1, 2006

By E. J. Peuraniemi

Recently commissioned Kennecott-Outokumpu flash converting was developed to replace the approved but environmentally outdated Peirce-Smith -converting to satisfy the globally tightening emission regulations. In the present study, dust formation and reaction mechanisms of two copper mattes with different experimental parameters were studied in lean suspension conditions. Both mattes had very high copper content of approximately 75 wt% and low iron content of 4.5 wt% and 1.2 wt% Fe. A laboratory scale, vertical laminar-flow furnace with a low feeding rate was used to simulate the phenomena taking place in the reaction shaft of a flash converter. Experimental conditions included temperature of 1300 °C with reaction gas oxygen contents of 20 vol%, 50 vol%, and 75 vol%. In the experiments, sieved particle fractions were fed to the furnace and sampled after short reaction time intervals by quenching them into a water film. Collected particles were analysed chemically for their main elements to define their removal rates. Also, optical and scanning electron microscopy with EDS-analyser were applied to determine phenomena occurring during reactions. Kinetics of oxidation as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are reviewed to describe dust formation and reaction mechanisms.

Jan 1, 1999

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999