Search Documents

By Jeaneth S. Benedetto

The physical and chemical processes developed for recovery of uranium and phosphor from phosphoro-uraniferous ore bodies consists of three basic steps: concentration of the phosphate bearing uranium by flotation, chemical dissolution of the concentrate by wet phosphoric acid and extraction of uranium by solvent. In this process two products are obtained: 1) uranium and 2) phosphoric acid. The purpose of this work was to develop technological know-how of phosphoric acid purification though an extraction of P2O5 by solvents. It was investigated by two lines of research. In the first one the uranium was extracted before the phosphoric acid purification. In the second, the phosphoric acid was extracted before uranium recovery. The comparison of the two processes is shown in this paper. Experimental work was developed on a laboratory scale to select and optimize the process variables. After the laboratory study, the research of extraction and stripping was continued on a pilot scale in pulsed perforated-plate columns in order to investigate the main operational and process conditions. The first phosphoric acid extraction experiments showed good results using a raffinate sample obtained from the uranium extraction process. It was possible to obtain a high purity phosphoric acid.

Jan 1, 2003

By Cody Burcher-Jones

The recovery of rare earth elements (REEs) through heap leach/in situ techniques from so-called ion adsorption clays (IACs) is attractive due to their inherent simplicity. However, the underlying mechanisms of these processes are poorly understood. In this study, the deportment of REEs in a typical IAC material has been investigated and was found to concentrate in the phyllo-layers of the clays, especially hallyosite, and was readily desorbed by various ion-exchange reagents indicating various potential routes to liberate them. Here we are reporting the use of seawater (0.5 M NaCl), spiked with various amounts of (NH4)2SO4, and found better extraction using a reagent mixture than NaCl on its own. Further, the leaching of REEs from a bed of clay material was investigated over time to understand the rate of transport through the stagnant material. Results indicate that REE release is likely to be controlled by diffusion through the clay material, while desorption in agitated systems is rapid. A degree of fractionation between different REEs can be observed during diffusion. Nonetheless, the successful operation of in situ leach operations for this type of material would depend primarily on how easily solution cocktails can be made to flow through the bed material.

By Lennart Hedlund

There is today a long and well-documented experience of the use of Boliden "Kaldo' technology for treatment of various feed matedals. The process is In commercial' operation in the Boliden Mineral's Rönnskär plant In Sweden for treatment of copper scraps and lead concentrates (In campaigns). This plant was built In 1976 for treatment of lead dusts from the copper plant but later modified to take other raw materials. Boliden's Kaldo techr:lology Is also In operation since 1991 for treatment of low-grade copper scraps In Enlrlsorse's plant In Porto Marghera (Venice), Italy. The plant is producing 25 000 tons of blister copper ,per year. The Kaldo furnace Isa high :Intensity smelting unit, where several successive treatment steps can be done In the same vessel. The furnace can be totally enclosed to protect the working environment, and the small off-gas volume can easily be dedusted. Input materials can vary over a very wide range, the products will be a dump slag with low (0,5%) copper and lead contents and black copper or blister copper. The dust from the process can be used for zinc production. A new development is autogenous smelting of scrap in a Pierce-Smith converter, implemented at Compagnie Générale d' Èlectrolyse du Palais in France.

Jan 1, 1995

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By V. A. Bryukvin

It has been found that by superimposing symmetric alternating current over the process, the rate of nickel and cobalt leaching from metallized products with copper sulfate solutions increases by a factor of 1.5 to 2.0 and the apparent activation energy of the process investigated is reduced from 12 down to 6.6 kcal/mole. It appears especially attractive to use alternating current for anodic dissolution (oxidation) of metallic scrap of refractory metals and their alloys in ammonia electrolytes permits production of high-grade commercial products in the form of respective ammonium salts using a short and virtually reagent-free process flowsheet. Similar approaches can be applied also for electrochemical processing of nickel and copper scrap in sulfuric acid media with subsequent recovery of pure sulfate salts or electrolytic processing. Electrochemical technology for recycling of tungsten-cobalt (WC 15) and tungsten-rhenium (WR 20) alloys has been also investigated. In the former case, anodic oxidation of carbide alloy was carried out in nitric acid electrolyte with production of pure tungstic acid. The research conducted has indicated that the physicochemical effect of alternating current results in a lower activation energy of electrode reactions due to changes in the mechanisms of the electrode reactions themselves.

Jan 1, 2006

By He De-wen

The increasing population and living standard in urban areas, have been accompanied with the growing quantity and composition complexity of rubbish, which are causing well-known social effects of pollution, while rubbish (solid waste) is a recyclable resource. To convert rubbish into useful materials, the essential measure is to carry out sorted collection of rubbish. The preconditions of implementing sorted collection are presented in the paper. 1 Characteristics of rubbish composition and amounts of recyclable contents are basic condition to implement sorted collection. 2 The existing available technologies of recycling, economic benefit from recycling, and disposal scheme of residual rubbish are restrained condition for sorted collection. 3 Public understanding and support to sorted collection are the key to success. 4 The government policies to be favorable for sorted collection is the pledge of success. 5 The establishment of a steady solid waste recycling market is also a guarantee to implement sorted collection continuously. 6 To establish management system of rubbish recycling as soon as possible. Further, the methods and procedure of sorted collection are discussed in detail and beneficial comments and theoretical basis to promote sorted collection of rubbish in urban area are presented; it will contribute reference value to municipal solid waste management.

Jan 1, 2006

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By Jitka Jandová

In this study, hydrometallurgical processing of waste ZnO flue dust arising during zinc removal from galvanized low-alloy steel sheets was investigated on a laboratory-scale to obtain electrolytic zinc. The flue dust was separated from flue gases, generated during heating waste galvanized steel sheets in an electric furnace under air atmosphere at temperatures of about 1000oC. The dust, comprising tetragonal ZnO and insignificant amounts of SiO2, was contaminated by Fe, Mn, Pb, Al, Mg, Pb, Cu and Ca. The dust was leached in 0.5 and 1.0M H2SO4 and/or in 20 and 30% NaOH at different temperatures and different liquid-to-solid ratios to determine the optimum conditions leading to the highest possible selectivity of leaching and efficiency of Zn extraction in minimum time. The subsequent electrowinning process was performed with refined zinc sulphate leach liquors and/or with untreated zinc caustic solutions. Zinc sulphate leach liquors were purified using a combination of a hydrolytic pH-controlled precipitation, cementation and carbon refining. Effects of operational variables on Zn electrowinning have been studied for both sulphate and caustic electrolytes. The conventional plate-plate electrowinning cell has been explored in this study. Comparison of results obtained for both zinc electrowinning from acid sulphate and alkaline solutions is presented contribution.

Jan 1, 2003

By J. P. Ibáñez

The uptake of copper from extremely dilute aqueous solutions by alginate in the form of protonated dry alginate beads was investigated. Barium was used to cross link the alginate forming the beads. The effect of various experimental parameters such as pH and metal ions concentration on the uptake of copper were studied. The uptake was strongly dependent on the Cu-bearing solution pH up to a value of 4.5. A removal of 100% o was achieved when the initial concentration of copper was as low as 8.0 mg/L. The maximum uptake, i, e., the loading capacity, was found to be 167 mg of copper per g of beads. The mechanism governing the removal of copper was found to be ion exchange between protons of the alginate beads and cupric ions of the solution. For this ion exchange process a molar ratio, d[H+]/d[Cu2+], of 2.0 was determined. EPMA-EDX analysis of the Cu-loaded beads showed a uniform distribution of the ions throughout the structure of the alginate, regardless the solution pH. This may suggest that this sorbent material is a porous ion exchanger having high permeability and capacity. The uptake of copper and of the heavy metals cadmium and zinc by this sorbent is compared.

Jan 1, 1999

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By Laurentiu Nastac

"The importance of investigating solute redistribution during the unidirectional solidification of multi-component alloys is broadly discussed in the literature. A previously developed analytical model that was experimentally validated for Al-Cu, Sn- Bi and Fe-Si dilute binary alloy systems is used in this article to study in detail the solute redistribution, the liquid/solid interface stability based on an extended transient constitutional undercooling criterion and the size of the initial transient region during the unidirectional solidification of Ti-6-4 and Ti-17 alloys. A comparison between Ti-6-4 and Ti-17 alloy systems with respect to interface stability and the size of the initial transient region is also provided. The effective partition coefficients of the alloying elements in these alloys were determined based on specially designed experimental measurements.IntroductionThe importance of investigating solute redistribution during alloy solidification is broadly discussed in the literature [1-5]. One of the relevant applications of this study would be the mathematical modeling of equiaxed and columnar solidification of multicomponent alloys. This includes the instability of the solid/liquid interface. There are several mass and heat transfer processes that involve the calculation of solute redistribution during directional solidification such as industrial directional solidification processes, continuous casting, remelting processes, Czochralski crystal growth technique, floating zone techniques, etc."

Jan 1, 2012

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By A. F. Otero

During the electrowinning (EW) of copper significant quantities of highly toxic vapors (acid mist) are produced due to the liberation of oxygen at the cathodes. Acid mist affects the health of operators, the environment and plant infrastructure. Acid mist can be decreased to acceptable levels by a combination of physical means (e.g. ventilation, plastic spheres over electrolyte) and chemical surfactants that decrease the surface tension of the electrolyte, modifying the way oxygen bubbles burst at the surface of the electrolyte. However, only few chemical surfactants are compatible with electrolytic applications, and they are not always used due to their high costs. This paper describes the application of a novel surfactant of natural origin (commercial name Mistop®) to suppress acid mist in copper EW process. Mistop® contains triterpenic saponins derived from the Chilean quillaja tree Quillaja saponaria Molina. The product is non-toxic, and poses no risks to the environment or to EW operators. Mistop® was tested at a laboratory, pilot plant and industrial scale in the world?s largest copper EW production plant at Radomiro Tomic (RT), CODELCO, Chile. At a Mistop® dosage of 8-9 ppm, acid mist decreased below the value accepted by Chilean regulations (< 0.5 mg/m3). At this dosage, Mistop® represents and economical alternative to chemical surfactants, and it is currently industrially used at RT.

Jan 1, 2003

By Ilkka V. Kojo

This paper gives an overview of the primary copper smelting business during the years of flash Smelting in the light of various projects taking into account the sustainability of copper production. Also the future challenges of copper smelting are addressed with special emphasis on the environment. Flash Smelting connected with either Peirce-Smith converting or Flash Converting offers the most economical and environmentally friendly alternatives for the smelting of normal and lean copper concentrates. For rich copper concentrates the feasibility of Outokumpu Direct Blister Flash smelting is, understandably, beyond compare. When the total investment costs for building a smelter and acid plant are considered, it is clear that Flash Smelting is the more feasible option compared to bath smelting. Reduction of equipment and operating cost is further achieved by the LUREC-process developed by Outokumpu Technology for operating plants with SO2-contents up to 25 % by volume. As an example the Kennecott-Outokumpu Flash Converting Furnace (FCF) has been in operation at Kennecott Utah Copper for 10 years and has achieved excellent results both environmentally and production vice. The FCF treats the entire output of the Kennecott Flash Smelting Furnace and has excess converting capacity. Furnace life, initially projected at two to three years, is now projected to be more than 5 years. It is likely the life will be essentially the same as a well-operated Flash Smelting furnace.

Jan 1, 2006

By C. O. Bounds

The magnetic properties of (NdDy)15Fe78B6 sintered magnets have been evaluated using powder prepared by Inert gas atomization. The atomized powder had a particle size distribution from 1 to approximate 1000 microns. The as atomized powders have been sieved into, coarse, intermediate, and fine fractions; magnetic properties were evaluated for the as produced powder and each fraction. A B, of 11.7 kG, a Hci of 11.0 kOe and a BHmax of 32.5 MGOe was -obtained on a sintered magnet made from the as-atomized powder. The magnet made from coarse powder exhibited a slightly higher B, of 12.1 kG, while that from fine powder showed a decrease in B, to 11.2 kG. Hydrogen decrepitation has been utilized to study its effect on the magnetic properties. Finally, cast ingots with a definite columnar structure have also been used to compare the magnetic properties of magnets of the same nominal, composition but of different alloy preparation process. Hydrogen decrepitation does not appear to improve the magnetic properties of magnets made from thin cast ingots. However, it does show a significant improvement in the Hci of magnets made from the atomized powders. Possible causes for the differences in the magnetic properties on magnets made from each process have been discussed in the paper.

Jan 1, 1992

By S. N. Ashrafizadeh

Nowadays, hard carbides have found various industrial application in the manufacture of cutting and drilling tools as well as metal forming devices. About 60% of the world tungsten production is consumed in the manufacture of hard carbide pieces. Regarding the high economic value of hard carbide components, i.e., Ni, Co, TaC, TiC, and WC, their recovery from scrap species is attracting much interest. In the current research, the cobalt and tungsten content were recovered from scrap cemented carbide pieces through the application of high voltage electrolysis in nitric acid media. By this method, cobalt and tungsten were initially recovered as cobalt nitrate and tungstic acid, respectively. The precipitate of tungstic acid was calcined at 800ºC after being washed twice with distilled water. A pure tungstic oxide was obtained. The effects of current density, electrolyte concentration, speed of agitation, and the surface area of the anode on the efficiency of the electrolysis process were investigated. The optimum conditions of current density of 1500 A/m2, an acid concentration of 1.5 M, and a cell temperature in the vicinity of 60 to 80ºC were obtained. At the optimum conditions, an acceptable rate of collapse for the anodic carbide pieces of about 3.1 g/h was achieved, which remained constant up to the completion of the recovery process without any passivation .

Jan 1, 2003

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Guo Jun

In this study, BaTiO3 ultrafine particles surface-modified with stearic acid were synthesized by the hydrothermal method in a system of BaCl2-TiCl4-NaOH. The effects of NaOH/TiCl4 molar ratio, Ba/Ti ratio and time on structure and morphology of BaTiO3 ultrafine particles were investigated experimentally. The formation mechanism of different crystalline BaTiO3 particles was discussed, and it is considered that in a hydrothermal system, the main factors determining BaTiO3 crystalline are H+ replacement of Ba2+ causing H+ deficiency and anatase growth units involving in crystal growth, which clogs the axial channel for Ba2+ transference. By means of increasing the alkalinity of system and barium content, H+ deficiency and involvement of anatase growth units in crystal growth could be effectively controlled. The results show that when molar ratio of NaOH to TiCl4 is 9 and ratio of Ba to Ti 1.5, and time 8 hours, high purity tetragonal BaTiO3 ultrafine particles with a narrow grain-size distribution and nonpolar surface are obtained at 240oC. The particles have excellent flowability, which is ascribed that the surface polarity of barium titanium powder modified with stearic acid is changed and the interaction between the particles is weakened.

Jan 1, 2006

By Esperidiana A. B. Moura, Michelle Gomes, Cordelia M. F. Escanhoela, Francisco R. V. Diaz, Angel Ortiz, Rene R. Oliveira

"This work evaluates changes in morphological, mechanical and thermo-mechanical properties of electron-beam irradiated HDPE/nanoclay and HDPE/Piassava fiber/nanoclay. Material samples irradiated with 100 and 200 kGy using a 1.5 Me V electron beam accelerator (room temperature, presence of air) were submitted to tensile, flexural, and HDT tests. MFI, SEM and XRD analyses were carried out. Correlation between properties was discussed. Results showed that incorporation of piassava (Attalea funifera Mart) fiber and nanoclay, followed by irradiation represented significant gain in thermo-mechanical properties. Changes in surface morphology and reduction in MFI were observed. In conclusion, it may be claimed that the incorporation of piassava fiber in small size particles and nanoclay in the HDPE followed by electron-beam irradiation effectively improved the polymer properties and led to materials with superior properties suitable for several industrial applications.1. IntroductionIn recent years, the preference for using natural fibers instead of synthetic ones in polymer composites has been growing significantly. In Brazil, due to the great diversity of woody and fibrous plants of our forests, a vast potential of natural fibers is found, presenting good mechanical strength properties, chemical and biological stability, fire resistance, abrasion resistance, shear strength and lightness, among other which may contribute to the development of new materials for different applications such as automotive, aerospace, construction, food segment, cosmetics and others [ 1]."

Jan 1, 2013

By I. A. Ibrahim

Ilmenite, in its natural form, is an inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite. so that it can be leached with dilute hydrochloric acid, can be enhanced by chemical reduction in solution using a suitable metal as a reducing agent. The present paper aims at the evaluation of an Egyptian ilmenite ore for the production of synthetic rutile by direct leaching with hydrochloric acid in presence of iron powder. In this process, the titanium and iron contents are dissolved; meanwhile, the dissolved titanium is hydrolyzed and re-precipitated leaving mainly iron in solution. Leaching conditions were optimized to obtain less iron in the final solid product. Addition of sufficient amount of iron powder during leaching reduces the dissolved Fe3+ to Fe2+ and reduces the dissolved Ti4+ to Ti3+. The creation of Ti3+ in solution is assumed to have a role in dissolving the ferric iron and hence increasing the reactivity of the ilmenite ore. Synthetic rutile of about 90% TiO2 and 0.77% Fe2O3 was obtained from ore with a grain size 100% passing 200 mesh and a 5-hour leach time with 20% HCl at boiling temperature (110°C) and 0.11 g iron powder / g ore.

Jan 1, 2003