Search Documents

By V. V. Geikhman

The paper updates the Plant experience in the development and implementation of an advanced environmentally friendly zinc production technology complying with the technological and economic level of producers in the world and the standards of maximum permissible gas emissions stipulated by the Russian legislation. General water recycling engineering allowed to ensure 95.6% water rotation level. All solid wastes formed during treating zinc concentrate are processed into marketable products or semiproducts and sold. As a result of implementing innovation techniques production at the Chelyabinsk Zinc Plant is non-waste.

Jan 1, 2006

By T. I. Arbuzova

The present work presents the original data concerning using a high pressure torsion method and a shock wave loading technique to produce compact oxide nanomaterials and investigations of the effect of severe plastic deformation on a microstructure, crystal lattice and stability of these compounds. This allowed us to compare two ways of deformation action that can be characterized as quasi-static and dynamic effect, correspondingly. Particular attention was paid to a stoichiometry and surface composition changes upon severe plastic deformations. A procedure for studying chemistry of the oxide nanomaterials by means of nuclear microanalysis and Rutherford back scattering has been worked through. For surface studies the X-ray photoelectron spectroscopy has been used. It was shown that both distortion methods permit to produce massive nano-scale oxide materials from the coarse-grained powder during a single technological cycle. Bulk nanocrystalline materials based on LaMnO3, TiOy and ZrO2:Y2O3 were obtained by the quasi-static deformation technique. Nanoscaled ceramics of CuO, Mn3O4 and LaMnO3 were produced by the dynamic deformations. The density of the nanoceramics comes to 99%. Size effects and specific imperfection of the nanoceramics obtained lead to a set of particularities of physical properties.

Jan 1, 2006

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By J. Dille

Metallic cobalt exist in two allotropic forms : the hexagonal compact a which is stable at low temperature ( ( 420') and the cubic form 0 stable at higher temperature. This latest form is the only one which is ductile. During the electrode position of Co, in moderate acidic conditions, we noticed a code position of both a and B forms. The influence of several parameters on the B/a ratio in the deposit was investigated. High acidity and the presence of Fe increased its ratio; on the opposite, high temperature promote the a phase. No significant influence on the material were noticed. The differentiation of a and B forms of Co is rather difficult and the method of J. Scoyer was improved quite successfully.

Jan 1, 1988

By Zviad Kovziridze

Structure of celsian ceramics in BaO-Al2O3-SiO2system is studied with electron microscope in the entire temperature region of baking interval. The process of the pores filling and the full consolidation of material growth at comparatively high temperatures of baking intervals are described.

Jan 1, 2006

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By Chai Li-yuan

The anodic behavior of AZ31 magnesium alloy in NaOH alkaline solution was investigated in this paper. The effects of anodizing parameters, such as applied current density, concentration of NaOH and temperature of the solution on the formation, structure and surface morphology of the anodic films were also studied. The formation of the anodic film was analyzed by analyzing the anodic polarization curves, the potential-time curves and XRD, SEM graphs of samples obtained at different anodizing time. The results of corrosion resistance tests, XRD and SEM observation showed that the temperature greatly affected the formation and anti-corrosion property of the anodic film, but the concentration of NaOH not. The film with best anti-corrosion resistance was obtained at applied current density of 10mA/cm2, 353k in 1mol/l NaOH solution.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Fumito Tanaka

The Converting Furnace (C-furnace) of the Mitsubishi process has solely provided opportunities for producing blister copper continuously from molten matte. Continuous converting originates from the proven technology for controlling the behavior of magnetite in lime-ferrite slag of the CaO-FeOX-Cu2O system. Recent improvements in the C-furnace operation have included the slag controls reflecting the impact of minor oxides on magnetite behavior. Although previous investigations focused on magnetite behavior, sulfur has also affected the C-furnace operation because it is of practical importance to avoid the precipitation of gypsum from lime-ferrite slag and the separation of matte from blister copper. This paper will quantify the behavior of sulfur in C-furnace with respect to the gypsum formation and matte separation, and discuss better controls for C-furnace operation.

Jan 1, 2006

By Finn Olesen, Melina Garcia, Mark William Kennedy

"Furnace resistance is a function of the complex interrelationship between many factors including: operating practice, slag conductivity, temperature, power intensity, and geometry (electrode shape, diameter, spacing, immersion, slag depth, etc.).Accurate prediction of resistance is critical for success of the overall furnace design. The sizing of electrodes, columns, bus-bars, and transformers are all impacted. Estimation of minimum and maximum resistance or maximum operational current, as well as the maximum operating voltage are of fundamental importance.Various mathematical tools have been developed to assist designers with the selection of furnace dimensions and the prediction of resistance. Elkem found the methods of Downing and Urban 1965 and Westly 1975, to be particularly useful.In the current paper, comparisons are drawn between data from spent aluminum pot lining (SPL) demonstration testing at Elkem Bjolvefossen and predictions based on these classical tools and 3D finite element modeling (FEM) with COMSOL.®"

Jan 1, 2012

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By Teruo Tanabe

The hydrogen-absorbing materials are expected to have the following properties at moderate conditions, (a) a large capacity of hydrogen absorption, (b) the absorption rate of hydrogen is large and (c) hydrogen-absorbed materials can easily desorb hydrogen. Thus the three concepts of capacity, rate and reversibility seem to be indispensable to clarify the mechanism of hydrogen absorption by the materials. In this work, the amount of absorbed hydrogen, the absorption rate and the reversibility of hydrogen absorption- desorption reaction were measured for binary R-M systems (R = Y, La, Ce; M = Co, Ni). These experimental results were discussed by the following three physical properties that were calculated by the extended Hückel method, i.e. the density of states unoccupied by electrons, the cohesive energy and the energy fluctuation. The major results are as follows: (a) the amount of absorbed hydrogen increases with the density of states in the energy range between -9 and -4 eV, (b) the R-M compounds of which energy fluctuations are large show a large value of rate of hydrogen absorption, and (c) when the cohesive energy is large, the compound has a tendency not to easily desorb hydrogen, i.e. its reversibility is poor.

Jan 1, 2006

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By Rauf Hurman Eric

In this review paper the effect of composition and temperature on electrical conductivity and viscosity of the slags encountered in electric smelting of PGM-containing sulfide concentrates is described along with their liquidus temperatures. Optimization of slag composition is attempted on the basis of opposite trends of viscosity and electrical conductivity. Metal losses to slag, matte-slag separation and matte settling are also discussed in conjunction with interfacial and surface tension concepts. The electrode immersed in the slag phase is the main factor in the design and operation of the furnace. The most important electrode parameters are the size and the positioning in the slag phase which are determined by the slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles within the slag phase which in turn affects the flow conditions. Thus the flow of slag is discussed together with furnace geometry, stirring action, buoyancy and electromagnetic effects and the action of the electric furnace as a settler is emphasized. A discussion on the design d production capacity of the furnace is provided which are based on considerations derived mainly from slag properties.

Jan 1, 2006

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Corby G. Anderson

Laboratory testing, interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid optimization of laboratory testing and operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing, this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By M. Nishikawa

The Hachinohe Smelter employs the Imperial Smelting Furnace (ISF) for production of zinc and lead and handles a large number of concentrates and recycled materials. In recent years, recycled materials such as zinc-bearing materials, lead sludge and Waelz oxide have provided up to 30% of the feed materials at the plant. To allow for a satisfactory operation using such a wide range of recycled materials, the Hot Briquetting Plant was built in 1986 and started its operation in January 1987. In April 1988 the zinc production capacity of the ISP was increased from 81,000 to 101,000 tonnes per year. The additional production in the ISP has been attributed to the utilization of the hot briquetting process. This paper describes the various facts of the smelter, concentrating on hot briquetting operations and treatment of hot briquettes in the ISF.

Jan 1, 1991