Search Documents

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By Roger L. Williams

The Bureau of Mines investigated northern New Jersey as a potential future source of yttrium and the rare-earth elements. The studies, consisting of geophysical surveying, sampling, and exploratory drilling, began in the spring of 1959. A total of three and one-half months were spent in the field collecting data. Thirty-three deposits were investigated, of which five demonstrated some potential resources of yttrium and rare-earth minerals. Results indicate that the deposits examined do not contain quantities of yttrium and the rare-earth elements recoverable under present economic conditions. Detailed studies conducted at the Scrub Oaks mine, near Dover, N. J., delineated a yttrium and rare-earth-bearing zone within the magnetite-hematite ore body that represents a potential low-grade deposit. Beneficiation studies on this deposit indicate that a final product, averaging 31.3 percent rare-earth oxides including yttrium, could be produced through amine and fatty acid flotation procedures with 77 percent recovery. Two hundred and eighty-five feet of diamond drill core was obtained from exploration studies conducted at the Bemco prospect in Sussex County. The deposit averages 2.30 percent rare-earth oxides (including yttrium), 0.45 percent uranium and 0.24 percent thorium. Low-grade deposits were identified at the Canfield phosphat2 mine and the Tanners Brook Monazite placers in Morris County, and the Marble Mountain prospect in Warren County.

Jan 1, 1967

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By T. Schmidt, J. Merza

"This study considers two lead/zinc/silver orebodies which have historically had a problem with pyrite, pyrrhotite and sphalerite contamination in the lead circuit. The problem was previously addressed with high dosages of sodium cyanide as the primary depressant. However, large amounts of cyanide led to environmental problems in the effluent, especially during winter months. The objective was to reduce cyanide consumption while maintaining or improving overall lead grade and recovery via the reduction of the undesirable sulphides.Extensive laboratory and mill testing was necessary to determine the optimal operating parameters for continuous plant application. Evaluation of data received from this testing has shown that selective addition and optimization of the dosage of Unimax SD100 to specific areas of the flotation and grinding circuits has resulted in improved Pb grade and recovery. Parameters such as pH control, regrind operation, the cyanide/Unimax ratio and sulphide mineral content may also affect the performance of the depressant. Each factor is discussed and optimal operating conditions were determined based on the testing.Results are presented for two case studies. Both indicate that Unimax SD100 improves the lead grade/recovery curve by increasing iron and zinc rejection while reducing cyanide consumption and the resulting environmental concerns. 1. Hart"

Jan 1, 1992

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

Permitting, engineering and evaluation, detailed design and construction aspects of the Golden Cross goldmining project in New Zealand are briefly reviewed. The extremely lengthy and complicated governmental approval process together with the delaying tactics of opponents of the project are outlined and comment is made on aspects of the draft legislation proposed as part of the overhaul of New Zealand's resource management laws.

Jan 1, 1990

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By Orlando Gallardo

El presente texto describe la implementación del software ADS (Sistema de Despliegue Activo) a los sistemas de control supervisor de los diferentes procesos del complejo metalúrgico a nivel administrativo -en tanto replica los archivos gráficos y de base de datos. Este servidor además de concentrar en su red de campo redundante data de controladores e instrumentos de campo, puede compartir información con clientes usuarios y clientes de visualización dentro de la planta. En ese sentido, el objetivo es simplificar la producción y uso de datos únicos y garantizar la fiabilidad de estos a tiempo real para todos los niveles de supervisión a nivel administrativo, al tiempo que se planea y optimiza los recursos con la toma de decisiones apropiada.

Sep 24, 2008

By L. R. C. Cairncross

In this study, the general case of semi-batch precipitation of nickel hydroxide, Ni(OH)2, is modelled. In practical terms, this precipitation may occur at high ionic strengths, and therefore the model for solution chemistry requires a thermodynamic model that is applicable for these non-ideal systems. The activity coefficient model used is the ELEC-NRTL. The simulation of the solution chemistry is performed using AspenPlusTM, which is a steady-state process simulation program. This allows for rigorous evaluation of the solution speciation, and hence the degree of supersaturation which dictates the precipitation kinetics. The solution chemistry provides the basis for predicting the formation of solids. The model consists of a solution chemistry part and a solids formation part. The inputs to the model include the initial concentrations of the streams entering the reactor, kinetic parameters for the precipitation processes, and a particle size distribution obtained from experiments. The solids formation part of the model employs the method of moments for the evaluation of the population balance. The population balance accounts for total particle number, and the formation and increase in size of particles across the entire particle size range. This balance requires kinetic parameters for the processes of nucleation, growth and agglomeration. Using optimization routines inherent in AspenPlusTM, parameters for the rate of nucleation, growth and agglomeration may be extracted from experimental particle size distributions. These are then used in the model to extrapolate to other conditions. Once an understanding of the kinetics of the precipitation processes is gained, the model provides a predictive tool for optimization of these kinetics, in order to increase the overall particle size and therefore improve solid-liquid separation. The work is deemed to be significant as it sheds some light on solids formation processes involved in precipitation?including nucleation, growth and aggregation?and develops a predictive modelling tool applicable to solutions of high ionic strength. We argue that this dewatering of suspensions is affected significantly by particle size distribution and surface properties of the solids formed by precipitation. This modelling tool should facilitate the design of solids formation processes where downstream dewatering is enhanced.

Jan 1, 1997

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE>LREE>HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

By J G. Webster-Brown, K L. Brown

The Waihi Region is host to many low sulphidation epithermal Au-Ag deposits. The Golden Cross mine located at the head of the Waitekauri River, eight kilometres NW of Waihi, was a gold mining operation that placed significant emphasis on environmental management. An assessment of the influence of this mining project on stream sediment geochemistry (Fe, Mn, As, Cu, Pb, Zn, Cr, Cd, Ni, Ag and Se) in the Waitekauri Catchment has been made. Effective waste management during the mine operation appears to have prevented contamination of stream sediment. Trace metal concentrations in the Waitekauri Catchment sediment have generally decreased since 1987, and are currently mainly below the ANZECC (2000) sediment quality guidelines. However, elevated As levels were recorded in the Upper Waitekauri River and Battery Stream, exceeding guideline values. Elevated levels of Cu, Pb, Zn and Cd were found in the Huanui Stream, a tributary of the lower Waitekauri River. This reflects the influence of past mining operations in the valley, as well as natural weathering of hydrothermally altered Coromandel Group andesite. At a number of sites, Mn concentrations also exceeded sediment quality guidelines, and this may be derived from the remediated Golden Cross mine site.

Jan 1, 2003

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By Kenneth N. Han, Peter Nam-soo Kim

A kinetic model for leaching of particulate metals in a batch system has been developed. The leaching mechanism has been analyzed by solving a series of ordinary differential equations relating heterogeneous reaction kinetics at the solid/liquid interface to mass transfer of reactant and products. Special emphasis has been given to the effect of changing of the surface area of the leaching substrate and initial particle distribution on the overall leaching rate. The dissolution of gold powders in acidic solution with bromine as an oxidant has been used as a model system. The effect of particle size, chemical reaction order, rate constant and mass transfer coefficient on the overall rate of dissolution of metal powder has been analyzed and discussed.

Jan 1, 2005

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011