Search Documents

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By Charles G. Kemsley

MR. C. R. WHITTEMORE: It is interesting to note that the mining industry is making increased use of alloy steels for drilling. They will undoubtedly lead to greater footage at lesser cost. Mr. Kemsley states that, for use in hard ground, the shanks are brought to a hardness of 435 to 440 Brinell by heating them to approximately l,800°F. It seems to me that this temperature is excessively high-it is considerably above the critical point of the steel. The only effect of such a high temperature is to lessen considerably the impact resistance of the steel. The possibilities of an oil quench, followed by a tempering draw which does not lessen the hardness of the steel too much but increases its toughness, might well repay further study; also the temperature control, a factor which depends on the composition of the steel. However, service results are undoubtedly the best criterion of practice. MR. KEMSLEY: I would like to point out that the steel is not quenched at 1,800°F. After heating to this temperature, it is laid aside to cool gradually; this high temperature is necessary to produce the required hardness by simple normalizing-cooling in still air. We all know that ideal conditions for hardening steel demand salt baths and furnaces with automatic temperature control, but for most companies the cost of such equipment having sufficient output capacity is prohibitive. The end we are trying to attain is to make good drills at a cost that will be within the means of any mine.

Jan 1, 1942

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. The image processing was performed using the Smartfroth software on the top surface of the froth. The system gives measurements of bubble size distribution, average bubble size and froth velocity. The froth velocity was used to estimate the volume of bubbles overflowing the weir yielding to the fraction of air overflowing the cell. This measurement is the complement of the rate of bubble bursting on the top surface. Also samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. Then, the amount of solids and liquid per unit area in the bubble lamellae was estimated gravimetrically. Both measurements were used to establish stability criteria.It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase to high frother dosage did not result in an improved fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance."

Jan 1, 2003

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

By E. J. Fuller, J. C. Monette

"Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and temperature. (1) Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits.This paper describes the development of a new chemical eluant which significantly increases the rate of stripping of both gold and silver cyanide complexes from activated carbon. Two case history applications are also described.INTRODUCTIONAdditional cyanide is used in strip circuits in order to prevent its depletion which could lead to precipitation of base metals or lead to a change in the nature of the gold cyanide complex to one which does not strip as easily. (2)The strip circuits that are able to function efficiently without the use of cyanide are mostly those where the carbon is acid-cleaned after stripping.Once the minimum cyanide requirement to maintain the complexes in their proper state are fullfilled, any futher incremental increase in the level of cyanide will have no bearing on the rate of stripping. (3)DEVELOPMENT OF THE NEW ELUANTGeneral DiscussionVarious carboxylated materials were investigated including octanoic acid, polycarboxylic acid (various molecular weights), salicylic acid, polymaleic acid, acetic acid. benzoic acid, terephthalic acid, 4, bi-phenyl carboxylic acid, phosphoric acid and stearic acid.The initial work was done on medium activiiy, non acid-cleaned carbon. The silver to gold ratio on the carbon varied greatly.Two different blanks were used. The first was an elution using a 2% caustic and 0.4% cyanide solution while the second was a 2% caustic elution."

Jan 1, 1992

I have spent most of the past 35 years working as an economic geologist in the area of exploration and development of base and precious metals. Most of this period has been as an employee of Trans-National-Corporations (TNC's). I presently act as a consulting geologist to a joint venture company, bringing together two such TNC's: Anglo American Corporation and affiliated companies De Beers (Diamonds) and Minorco (Metals mining outside of Southern Africa), and Normandy Mining Limited ofAustralia. Normandy is presently through its gold arm PosGold, Australia's largest gold miner and Anglo American can claim to be the world's largest gold company producing over 280 tonnes of gold a year, more than twice its nearest rival Gold Fields of South Africa. In addressing this topic, the role that Government can, and should play in mineral development, I will be drawing heavily on some examples from these and other TNC's experience in recent offshore mining investment.

Jan 1, 1995

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

The typical reactions which the reductants undergo during ferroalloy production are reviewed, and identified as reaction with CO2 and with SiO, and dissolution in metal. Available reactivity tests for these three reactions are reviewed. It is proposed that it is worthwhile considering dissolution kinetics as a reactivity parameter. Greater crystallinity of the reductant decreases CO2 and SiO reactivity, but increases dissolution rates.

Jan 1, 2002

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By Evgenii Pavlov, Ivan Tronin, Viktor Timofeev, Vladimir Kislov, Sergei Bogovalov

"Modeling of the magnetohydrodynamical (MHD) and thermodynamical processes during the industrial scale Direct Chill (DC) casting of aluminum slabs is performed using a combination of ANSYS/CFX and ANSYS/EMAG software. The electromagnetic field is modeled through ANSYS/EMAG, while hydrodynamic and thermodynamic processes are modeled through ANSYS/CFX. Both packages were modified in order to calculate MHD flows in the liquid pool that forms during aluminum DC casting, and they were unified into a software combination that provides simultaneous simulation of all the above processes. The simulation shows that the electromagnetic stirring of the molten aluminum changes the shape of the solidification front (solid-liquid interface) very dramatically, namely it becomes significantly flatter. This effect should improve the internal structure of aluminum DC slabs and allows us to increase the casting velocity.IntroductionProduction of Aluminum alloys with high mechanical properties and structural uniformity is one of the main goals of industry. The preferred production method of aluminum alloys in most modern plants is Direct Chill (hereafter DC) casting because it offers high productivity and commercial success. One important limitation of this technology is the development of centerline shrinkage in slabs larger than about 1 meter. The improvement of the internal structure of long DC cast slabs can be achieved by electromagnetic stirring (hereafter ES) of the liquid metal above the solidification front. This intensifies heat transport in the zone close to the solidification front and suppresses shrinkage formation."

Jan 1, 2013

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

By Paul M. Tyler, Colin G. Fink

THE field of rare metals is so broad that progress can be reported upon many important fronts. Not satisfied with the 92 elements that Mendeleeff and his followers have accepted as legitimate, scientists are trying now to complicate matters by making new elements. Enrico Fermi announced the fabrication of "Element 93". Uranium, instead of being allowed to disintegrate slowly according to its normal habit, was bombarded with neutrons until some of them seemed to have stuck in the nucleus. To understand just what is alleged to have happened all one has to do is to line up the elements in their usual order of ascending atomic weight and imagine, as physicists do, that each atom is a little solar orbit comprising a central mass or planet about which other masses revolve like satellites. Ordinary hydrogen, being very light, consists of only one positively charged proton center, with only one positively charged electron revolving about it. Other atones are progressively more complicated until we come to uranium, which has a relatively big center and 92 particles revolving around it.

Jan 1, 1935