Search Documents

By Enrique Toledo G

Dado que la vanguardia tecnológica en la perforación y transporte subterráneo minera es cada vez mayor, se hace necesario que las labores mineras se adecúen al funcionamiento del sistema. En este sentido, el método tradicional de cuadros de madera en la minería subterránea sin rieles quedó desplazado, surgiendo alternativas modernas como el empleo de arcos metálicos revestidos con concreto armado, el bulonado con diferentes tipos de pernos de roca y la aplicación del Sholcrete. Entre estos últimos, la mina Cobriza ha desarrollado un nuevo método de sostenimiento denominado "Shot Fer", el cual satisface el desarrollo de las labores mineras, asegura la estabilidad permanente de las labores subterráneas en terreno deleznable, disminuye los altos costos unitarios en el sostenimiento de las labores subterráneas y garantiza la seguridad contra los accidentes que pueda sufrir el personal que trabaja en la perforación y en las operaciones de sostenimiento.

Nov 8, 1984

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By Bernard H. Hertlein

"When the Deep Foundations Institute (DFI) was founded, quality assurance and quality control (QA/QC) of foundation construction was rudimentary. Nondestructive testing (NDT) was a nascent technology, known to very few people, and very limited in its capabilities and applications. In the four decades since the DFI became a reality, NDT researchers and practitioners have taken advantage of technological advances to improve those existing testing and analysis techniques, and to create new ones that have all contributed to the engineering body of knowledge. This has enabled contractors to improve the quality and reliability of their products, and engineers to design more efficient foundations.Through its regular series of seminars, publications and annual meetings, the DFI has been vitally important in educating the deep foundations industry about the capabilities and benefits of NDT methods. In turn, NDT results have helped the industry identify problems in deep foundation construction, determine the causes of those problems, and improve design constructability and construction practices to increase the quality, reliability and efficiency of all types of deep foundations. This presentation reviews the evolution of several important NDT methods, and the contributions that they have made to foundation quality.THE BEGINNINGSThe Deep Foundations Institute (DFI) was incorporated in 1976 in the State of New Jersey as a 501(c)(6) non-profit association. The DFI is a consensus organization of Contractors, Engineers, Owners and Suppliers involved with the design and construction of all types of deep foundations. The purpose of the DFI was and still is to improve the planning, design and construction of deep foundations by educating all those involved, sharing best practices, and promoting the adoption of new technologies that improve quality, productivity or safety.This is well expressed in the current DFI Mission Statement: To bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and a consensus voice for continual advancement in the deep foundations industry.At the time the DFI was born, nondestructive testing for verifying the quality and integrity of deep foundations was in its infancy, its growth constrained by the technology, or lack thereof. Some visionary engineers of the time understood the physics of the potential methods, and therefore the possible capabilities, but were frustrated by the lack of technology to work with. Electronic equipment was mostly analog, and the few digital data acquisition systems that were available had such slow sampling rates that they were incapable of recording rapid event sequences or short duration events such as those used in modern integrity tests. For example, Jean Paquet, a leading research engineer at the French National Construction Institute, (Centre Experimentale de Recherche et d’Etudes du Batiment et des Travaux Publics, or CEBTP) patented the frequency-based analysis procedure for the Transient Dynamic Response (TDR) method, aka Sonic Mobility or Impulse Response, in 1974, but it was not until 1977 that analog data acquisition systems became fast enough to turn his theory into a reality."

Jan 1, 2017

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By Fred N. Kissell

In This Chapter [Instruments available to measure methane in mines and tunnels Using a portable detector in both accessible and restricted spaces Machine-mounted monitors: placement and response time Calibration of catalytic detectors for different gases and Misinterpreting warning signs This chapter gives guidelines for methane measurement in mines and tunnels. The emphasis is on the measurement procedure and the interpretation of the measurement rather than on the instrument itself.] The failure to properly sample for methane is a major contributing factor to methane explosion risk. Sampling errors are most likely to occur at mines or tunnels where the presence of methane is not suspected or during nonroutine tasks at mines or tunnels known to have gas. More specific information on methane sampling at continuous miner sections is in Chapter 3. Chapters 4 and 5 discuss sampling at longwall sections, and Chapter 14 discusses sampling at tunnels. METHANE DETECTORS FOR MINING Many models of gas detectors are available to measure methane concentrations, as well as most of the other contaminant gases found in mines and tunnels. An example is the iTX Multi-Gas Monitor, a portable gas detector available from Industrial Scientific Corp., Oakdale, PA. This handheld instrument measures several gases simultaneously. The cost (2004) ranges from $1,300 to $2,200, depending on the number of gases measured. Similar instruments are available from other manufacturers. Most methane detectors used in mining use a catalytic heat of combustion sensor to detect methane and other combustible gases. These have been proven through many years of reliable operation. For detection of methane, proper operation of catalytic heat of combustion sensors

Jan 6, 2006

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

The Hopi Reservation is in Arizona, where coal mining can be traced to the 13th century. Bituminous coal is found in varying quantities throughout the Hopi Reservation. The Hopi Tribe has a 50 percent mineral interest in the coal resources of the joint-use area adjacent to the Navajo reservation. The only coal presently mined on acornrnercial scale from lands in which the Hopi Tribe has an interest is from the Wepo formation at the Black Mesa and Kayenta Mines. These two large surface mines, located over 50 miles northeast of most Hopi settlements, have disturbed more than 6,000 acres. Income from royalties generated by the mines provides significant economic support for the Hopi Tribe. The Office of Surface Mining's Albuquerque, New Mexico, Field Office is responsible for regulating mining and reclamation on Hopi land. The Hopi Abandoned Mine Land Program was approved June 28,1988.

Jan 1, 1992

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By Ray Patterson

A planned modification to a cement kiln at the Holnam Portland Cement Plant near Florence, Colorado required the removal of a ring of cast-in-place (CIP) refractory lining. The CIP lining was approximately 14 inches wide, 12 inches thick and 38 feet in circumference.

Jan 1, 1999

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

One way to upgrade iron ore is to process it into pellets. The pelletizing process is multifaceted, involving complex fluid dynamics with highly turbulent, high-temperature flow in intricate geometries. This makes it hard to perform measurements during operation, so a useful tool for better process understanding is computational fluid dynamics (CFD), where the challenge is to perform efficient and trustful simulations of complicated problems. A validated simulation model can be valuable for increased process control and development. In this paper, the flow field and coal combustion process in a pilot-scale iron-ore pelletizing kiln is simulated using a CFD model. The objective of this work is to apply a coal combustion model to enable an investigation of thermal effects from the flame on the surrounding flow field.

The increased cost of imported oil fuels, coupled with our understandable reluctance to commit ourselves to the use of nuclear energy, has resulted in a renewed reliance on coal as a primary source of energy. New Zealand is fortunate in being fairly well endowed in its coal resources, but their exploitation until now, has been on a relatively small scale. Future exploitation, whether from underground or open cast mines, must be on a very much larger scale. This paper outlines some of the factors which should be considered in planning large open cast mines.

Jan 1, 1976

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By David E. Kaslow

In sampling dust laden air by drawing the medium into an inlet, some larger particles fail to follow the air and a true sample is not obtained. Inertia prevents particles from accelerating with the air as well as from turning sharp bends; also the particles' weight causes them to fall relative to the air. An analytic solution to the sampling efficiency calculation by Levin gives particle paths and sampling efficiencies for various particle sizes when the inlet can be treated as a point sink. However, the flow field in the neighborhood of an aspirating tube is quite different from a point sink flow. Employing Levin's solution in the outer field, trajectories in actual flow fields have been calculated by computer to locate the critical trajectories separating the entering particles I paths from those paths where the particles hit the tube wall or escape. Sampling efficiencies are presented in terms of 3 variables--a dimensionless particle size coefficient, a dimensionless orifice size coefficient and the tube orientation--for the no-wind case. Over most of the range of sampling conditions, the Stokes drag law can be used and dependence on the variable--particle Reynolds number--can be ignored. A procedure for achieving maximum efficiency in design of a sampler is proposed. Whether these results apply when typical room-sized eddies constitute the ?calm air? environment is not known.

Jan 1, 1974

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By C. M. McKinney

This report contains Bureau of Mines routine crude-oil analyses of 20 samples from5 areas on the arctic slope of Alaska. Two samples were condensates from the South Barrow gasfield, Barrow Lakes area. The remaining 18 samples were crude oils from the following areas: Barrow Lakes, 1 seepage sample; Umiat, 10 well samples; Cape Simpson, 1 seepage sample and 3 well samples; Fish Creek, 2 well samples; and Wolf Creek, I well sample. Table 1 summarizes information on the origin of the crude-oil samples, and table 2 summarizes characteristics of the samples. Item numbers in both tables correspond to item numbers of the analyses at the end of this report, and the samples are referred to by these numbers throughout the text.

Jan 1, 1959

By J. R. Thoenen, Hugh D. Pallister

"INTRODUCTION The Stone Hill Copper project resulted from the recommendations made in the war minerals report on this deposit by engineers of the Bureau of Mines 4/ and a similar report of the Geological Survey. 5/ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell E. Moon, chief, conducts preliminary examinations, does the actual investi¬gative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.This report was prepared under the supervision of Paul M. Tyler, former regional engineer, Eastern Region, and is based on the examination and investigation of the deposit by Hugh D. Pallister, mining engineer, made under the immediate supervision of Richard W. Smith, former District Engineer for Alabama and Mississippi.The report was rewritten and prepared for publication by J. R. Thoenen, chief, Tuscaloosa Branch, Mining Division.LOCATION AND ACCESSIBILITYThe Store Hill copper mine is about• 12 miles south of Heflin, the oounty seat of Cleburne County, Ala. Heflin, a town with a population of approximately 1,700, is the nearest shipping point for freight and express. It is on the Southern Railway, between Birmingham and Atlanta. A rural mail route passes within quarter of a mile of the mine. Paved reads from Heflin lead to Atlanta, Birmingham, and Montgomery. The country Toads leading from Heflin are well-maintained but are practically inaccessible during inclement weather. The road crossing the property within a hundred yards of the mine needs grading and repairing (see fig. 1)."

Apr 1, 1948