Search Documents

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By Shouchen Dun, Zong-Ming Li

Manipulation of hand-held objects in 3D space is a complex task. Understanding how individual digits interact with a hand-held object provides helpful information for hand tool designers, researchers, clinicians, and occupational therapists. At the object-digit interface, the contact mechanics can be represented by three force and three torque components. Six-component force/torque transducers can register all the three forces and three torques at the digit-object interface, and therefore are advantageous in the study of manipulation mechanics. The large number of force and torque signals from multiple force/torque transducers are difficult to interpret and therefore making experimental research of manipulation a challenging task. The purpose of this study was to develop a 3D visualization tool for the investigation of the contact mechanics at the object-digit interfaces during manipulation tasks. Methods A 3D stick-figure hand model was created based on digitized 23 anatomical landmarks of the hand. Five miniature 6-component force/torque transducers (4 × Nano17 for the fingers, 1 × Mini40 for the thumb, ATI Industrial Automation, NC) were used to record force and torque data at the tips of individual digits. Thirty channels of force/torque signals from the transducers were collected by a 16-bit analogue-digital converter (PCI-6031, National Instrument, Austin, TX) installed in a computer. The transducers were mounted on a custom-made rectangular aluminum handle for object manipulation. Coordinate frames were established at each transducer, on the handle, and at the base of the MicroScribe digitizer. To visualize the force vectors at the digit-tips, the coordinates of the hand landmarks in the MicroScribe coordinate frame and the force vectors in local transducer coordinate frames were transformed to a common coordinate frame defined on the handle. One healthy right-handed, male subject participated in the experimental study. During the tests, the participant sat in a chair by a testing table. The forearm was strapped to an arm holder in neutral rotation position. The instrumented handle was fixed on the testing table by a C-clamp through an adapting plate. With the hand of the subject gripped on the instrumental handle, the landmarks of the instrumented handle and the transducers, as well as the anatomical landmarks of the hand were digitized using the MicroScribe digitizer for the purpose of coordinate frame establishment and transformation as described above. The subject performed three different maximum isometric voluntary contraction tasks: (1) grasping, (2) rotating in pronation, and (3) lifting. Results The 3D hand model and representative force vector clusters in a single trial of grasping, rotating, and lifting tasks are shown in Figure 1. Each cluster was formed by displaying all the 3D force vectors during the period of “stabilized” maximum effort in a trial. The magnitude and

Jan 6, 2006

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970’s, only the sub-aeration mechanical cells were dominant. Since the 1980’s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs."

Jan 1, 2003

By Luis Ramirez Grados

El presente texto examina los problemas de diseño que se presentan en el sistema de minado subterráneo debido a su interrelación con los variados escenarios geológicos. Para ello, se cita el ejemplo del acarreo de desmonte y mineral de la Estación de Carguío H-2 del Nv. 2430 de la Rampa RNG 92442 @ -15% hacia el echadero de desmonte y la Tolva de Mineral de la Planta Concentradora en superficie Nv. 2765, donde el sistema de acarreo fue modelado usando simulación, la cual fue utilizada para ver la rentabilidad del sistema scooptram-volquete.

Sep 14, 2009

By R. T. DeWoody, J. W. Chester, W. C. Miller

The work was done to develop a relatively efficient muffler for quieting the exhaust of a rock drill . The exhaust of a pneumatic rock drill is the source of the major part of the noise generated by the drill . The exhaust noise can be reduced in a number of different ways , but this study involved only reactive mufflers . The reactive muffler can be simulated by an electrical circuit . Information obtained from analogous electrical circuits was used to design an efficient exhaust muffler for pneumatic rock drills . Electrical analogies proved to be a valuable tool in the design of mufflers .

Jan 1, 1964

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By Joseph J. Wallace, William H. Tavenner, D. A. Reynolds, John M. Provost, James J. Dowd, R. F. Abemethy

"CONCLUSIONSThe investigation shows that there are 5 coal beds of major importance in Wyoming County from the standpoint of present production - Pocahontas No. 3, No. 2 Gas, Sewell, Beckley, and Eagle - and 5 beds of minor importance - Pocahontas No. 6, Cedar Grove, Winifrede, Douglas, and Chilton. The Pocahontas No. 3 bed contains the largest remaining known reserves.Known measured and indicated reserves in all beds, based on a minimum thick¬ness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,665 million short tons as of January 1, 1951. Of this total, 2,121 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Wyoming County, as determined by this investigation, is 55.0 percent. This percent¬age is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. The known recoverable reserves are estimated to be 1,167 million tons as of January 1, 1951.4. Since most of the Wyoming coals are medium- and low-volatile bituminous in rank and expand during carbonization in modern ovens, they are blended with high-volatile contracting coals."

Apr 1, 1953

By Mark D. Hannington

Drilling of the active Trans-Atlantic Geotraverse (TAG) deposit during ODP Leg 158 indicated that the size of the mound-stockwork complex is approximately 3.9 million tonnes, including 2.7 million tonnes of massive and semi-massive sulfide (ca. 2% Cu) at the seafloor and 1.2 million tonnes of mineralized breccias (ca. 1% Cu) in a subseafloor stockwork. Quartz-pyrite veining in the stockwork zone extends from about 40 meters below seafloor (mbsf) to a depth of 95 mbsf. Siliceous wallrock breccias in the lower part of the stockwork grade abruptly into chloritized basalt breccias at the margins of the mineralized zone, and massive sulfides at the flanks of the deposit onlap relatively unaltered, partially hematized basalts. The pipe-like dimensions of the stockwork zone do not exceed the diameter of the sulfide mound. Comparisons with samples collected during earlier dive series confirm that the vent complexes at the surface of the mound are not representative of the bulk composition of the deposit. Dramatic vertical zonation of metals within the mound suggests that a long history of hydrothermal reworking has effectively stripped the constituents that are soluble at lower temperatures from the massive sulfides and concentrated them at the top of the deposit through a process of zone refining.

Jan 1, 1998

By D. S. Yantek, C. B. Brown

The mining industry is beginning to implement lithiumion batteries (LIBs) to power mine utility vehicles (MUVs) and rubber-tired mantrips (RTMs). However, the ability of LIBs to withstand the harsh conditions for these applications has not been rigorously evaluated. Concerns with the use of LIBs in the mining environment will be discussed including the effects of mechanical shock and vibration, temperature extremes, and moisture exposure. This paper will discuss adverse effects of the mining environment on LIBs and provide an overview of scientific gaps associated with the environmental susceptibility of LIBs used on MUVs and RTMs.

Feb 1, 2024

By Fábio de Oliveira Braga

Atualmente, tecidos de fibras sintéticas como a aramida (Kevlar®) e o polietileno (Dyneema®) têm sido os preferidos para proteção balística contra munições leves, e para integrar sistemas de proteção contra calibres superiores, como o 7,62 mm. Porém, por apelos econômicos, ambientais e da disponibilidade limitada destes produtos, materiais alternativos têm sido testados. Neste cenário, destacam-se os compósitos reforçados com fibras naturais, que têm demonstrado bom desempenho balístico. Assim, o objetivo deste trabalho é avaliar o desempenho individual de compósitos reforçados com fibras naturais de curauá, quando submetidos ao impacto balístico com munição 7,62 mm. Foram executados ensaios balísticos, medindo-se a energia do projétil absorvida pelos materais, e os resultados tratados estatisticamente por Anova e teste de Tukey. Mostrou-se que estes compósitos têm potencial para substituir as fibras sintéticas em sistemas de blindagem para proteção pessoal, com a vantagem de serem materiais leves, de baixo custo, nacionais, de ampla disponibilidade e ambientalmente corretos.

Aug 17, 2017

By V. A. James

The new electrolytic copper refinery situated at Copper Cliff, Ontario, has been in operation for over a year and a half. This plant is operated by the Ontario Refining Company, Limited. The associated companies behind the enterprise are the International Nickel ?company of Canada, Limited, the American Metals Company, Consolidated Mining and Smelting Company of Canada, Limited, and Ventures, Limited. The plant was an outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as compactly as possible. Starting anode furnace operations in June, 1930, and electrolytic refining on July 1st of that year, after a record-breaking construction programme completed in only fifteen months, the plant soon settled into its stride and the usual starting-up difficulties were .rapidly overcome. The rated capacity of the plant, namely, twenty million pounds of refined copper per month, has, of course, never been reached, due to depressed business conditions and latterly to the world copper agreement limiting production. It may be said, however, that the present installation has proved its ability to produce in excess of its rated capacity, and with relatively minor additions to plant and equipment that capacity can be doubled. Owing to the severity of the winters, when temperatures of from 20 to 40 degrees below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were rather unusual in copper-refinery construction.

Jan 1, 1932

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

By André Vervoort

After the systematic closure of Europe’s coalfields in the late twentieth century, the emphasis is now clearly on industry’s environmental legacy. One aspect of the latter is the longterm surface movement above abandoned coal mines. The analysis of satellite data shows that the subsidence lasts longer than generally assumed. However, a few years after the flooding of the abandoned underground coal mines, a new phenomenon was observed, i.e., the direction of the surface movement was reversed. The phase of upsidence has already lasted for several decades, and only future measurements will tell how long it continues. A key conclusion is that the regions with maximum subsidence do not necessarily correspond to the greatest upsidence. In other words, buildings and infrastructure are subjected to a different loading from this upsidence than during the subsidence phase. The longterm surface movements have an impact on vulnerable structures in the densely populated regions of the former deep coal mining areas in Europe. These movements create additional damage. This new knowledge is also relevant for mines that are still in operation or future mines that are planned.

Feb 1, 2024

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932