Search Documents

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By Willie M. NeSmith

Cast-in-place piling are a staple of the deep foundation industry, and are used (in various forms) worldwide. In assessing the application of cast-in-place piles, it is of value to reflect on the development of the various systems, in order to understand how the current processes and equipment came to be. This paper traces the evolution of the cast-in-place industry. Emphasis is on developments in the United States; however, since there has been a substantial fusion of US and European processes, notable European developments are also discussed.

Jan 1, 2006

By T C. Westerfield, G, M J. Mankosa

An innovative separator known as the HydroFloat cell has been developed specifically for the upgrading of coarse particles that are difficult to recover using conventional flotation cells. The novel characteristic of this separator is the formation of a hindered teeter-bed of fluidised solids into which small air bubbles are injected. The air bubbles selectively attach to hydrophobic particles and form particle/bubble agglomerates that segregate atop the teeter-bed due to their lower apparent specific gravity. The low-density agglomerates are eventually carried into the product overflow launder by the rising current of teeter water. Hydrophilic particles remain in the teeter-bed and are discharged to underflow as a high solids content tailing. Benefits of this hybrid flotation-density separator include enhanced bubble-particle contacting, increased particle residence time, and very low air demand. Test data indicate that significant improvements in the recovery of coarse particles can be achieved using this innovative technology. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent pilot-scale tests conducted for the phosphate industry.

Jan 1, 2005

By Yasushi Ishikawa

The fact that the degree of granulation and the state of granulated particles of sinter raw mixtures are the influential factors in ensuring coke combustibility and permeability during sintering has been clarified. Based on this knowledge, Nippon Steel developed the divided coke-addition process and the technology to utilize binder, and applied them on a commercial scale. Productivity and sinter quality are thereby greatly improved with a significant reduction in fuel consumption.

Jan 1, 1977

By Stephen J. Juras

The Myra Falls deposits comprise a complexly metal-zoned polymetallic volcanogenic massive sulfide district located 90 km from Campbell River in central Vancouver Island, British Columbia, Canada. The massive sulfide deposits are hosted by subaqueously-deposited rocks of the Devonian age Myra Formation of the Sicker Group volcanic assemblage. The deposits comprise many individual massive sulfide lenses grouped into several major zones within two main felsic volcanic stratigraphic intervals - the upper Lynx-Myra-Price Horizon and the lower H-W Horizon. The largest of these zones, the H-W and Battle, occur within the H-W Horizon. The first claims in the area of what is now Boliden-Westmin?s Myra Falls Operations were staked in 1917. Early prospecting resulted in the discovery of three massive sulfide showings which eventually became the Lynx, Myra and Price mines. Sporadic exploration was carried out until 1961 when Western Mines Ltd. (now Boliden-Westmin Ltd.) acquired the claims. Subsequent ore definition outlined 1.9 million tonnes of ore (approximately 5 years of mine life) in the Lynx deposit, and mining began in 1966. Pre-mining geological reserves (to January 1, 1997) comprised 6.7 million tonnes grading 3.3 g/t Au, 130.6 g/t Ag, 2.0 % Cu, 1.4 % Pb and 10.2 % Zn for the Lynx-Myra-Price deposits, 17.1 million tonnes grading 2.3 g/t Au, 32.7 g/t Ag, 2.3 % Cu, 0.3 % Pb and 4.2 % Zn for the H-W deposits and 4.2 million tonnes grading 1.1 g/t Au, 27.0 g/t Ag, 2.2 % Cu, 0.5 % Pb and 12.0 % Zn for the Battle deposits. Property-wide production to January, 1996 has been 15.7 million tonnes grading 2.1 g/t Au, 58.7 g/t Ag, 1.9 % Cu, and 5.2 % Zn.

Jan 1, 1998

By J. R. Sweet

The paper describing the raining operations at the Mt. Hope mine, Mt. Lope, N. J., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs of various mining operations in the United States. Mt. Hope mine produces magnetite ore. It is situated in the general northern part of the State of New Jersey. The towns of Rockaway, Wharton, and Dover lie within a radius of 4 miles from the mine. Dover is 40 miles from New York City.

Jan 1, 1932

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and' Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year's contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented was more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the Competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592, an increase of more than 100 per cent over the previous year's total of 2,259,572 hours. The frequency of accidents declined from 74.4 per million hours for all plants enrolled in the first year's contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930. The actual number of accidents reported for 1930 by 76 plants included four deaths and 206 injuries whereas the 26 plants that were enrolled in 1929 reported three fatalities and 165 injuries. Under the rules of the contest all "lost-time" injuries are reported--that is, all injuries that disable an employee for more than the remainder of the day on which the accident occurred. If the employee is physically able to resume his work on the day following the accident, the injury is not classed as a lost-time injury. The contest covered accidents and man-hours worked by all employees at the plant who were employed by the same company, and included work up to the point of delivery of the material directly to consumer or to independent agency of transportation--in other words, to point of relinquishment of control of the material by the producer.

Jan 1, 1931

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By I P. Hodkinson

SMC Resources Limited is implementing a selective mining approach at the Hadleigh Castle mine, formerly operated by Aurora Gold Limited. The main ore zone has a length of 250 metres and dips at 40 - 45¦ to the south. Gold mineralisation occurs in a variety of quartz-sulphide lodes in sericitised granodiorite. Shallow dips, alteration intensity and mineralisation style combine to make mining relatively difficult. Previously unworked, high-grade, shallow dipping (30 - 45¦), narrow quartz-sulphide lodes within the hanging-wall of the deposit are also being selectively exploited. Annual production of 35 000 oz Au is forecast from 185 000 tpa ore grading 6.5 g/t Au over a currently envisaged mine life of six years. Operations completed to-date include deepening the decline and access development of the first two levels beneath the previous workings. Longhole stoping operations have commenced in the main ore zone with air leg stoping also underway in the hanging wall lodes.

Jan 1, 1998

By Larry Schneider

In recent years, many individuals looking into the future of the blasting industry have predicted that the most likely next technological breakthrough would be the use of high precision, digitally controlled detonators. This seemed logical since not only was there much room for improvement in this area, but any significant improvement in delay timing could yield great benefits in productivity and control of adverse effects. And in fact, within the past two or three years, such electronic detonators have been introduced in the field by a number of different manufacturers. These systems are currently being used in many routine blasting operations around the world which are being closely watched and evaluated.

Jan 1, 2006

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By Britt H. Hatfield, Jiu-Chiuan Chen, Wen-Ruey Chang, David C. Christiani

Occupational exposures to whole-body vibration (WBV) at different frequency domains may differentially affect human comfort and the musculoskeletal system. Under this presumption, a frequency-based weighting scheme has been adapted in many widely accepted standards for WBV measurement. However, there is very little human data showing a direct link between WBV frequency and musculoskeletal disorders. We conducted an epidemiologic study to examine the association between WBV frequency and prevalence of low back pain (LBP) and to identify determinants of specific frequencies associated with LBP in urban taxi drivers. Methods The WBV frequency data were collected from 247 professional drivers (aged 44.6±8.3) who participated in an exposure validation study 1 of the Taxi Drivers’ Health Study (TDHS) in 2000. 2 In accordance with the ISO 2631-1 (1997) methods, we measured the frequency-weighted acceleration over drivers’ seat surface, under conditions representing randomly assigned destinations. We developed a WBV record-replay system at the Liberty Mutual Research Institute (LMRI) in Hopkinton, MA, USA. This system includes two tri-axial accelerometers (PCB Piezotronics, NY, USA), one RD-130T PCM data recorder (TEAC, Tokyo, Japan), and one LMWBV meter 2.0 (LMRI, MA, USA). Only the vertical axis of seat-surface WBV frequency was used in this study. To characterize the WBV frequency curve, we manually identified the presence of any peak within each of the following frequency range: <4, 4-10, 10-20, and >20 Hz. Information about the operating vehicles and driving environment was either collected from the vehicle registration record (manufacturer, year of make, transmission, engine size, etc.) or directly measured (wheel-base length, seat inclination, etc.). Structured interviews were conducted by an occupational physician to gather information on LBP that had led to medical attention or absence from driving in past year. We used multiple logistic regression to estimate the prevalence odds ratio (OR) associated with the presence of each index peak frequency, adjusting for age, body mass index, professional seniority, daily driving hours, seat inclination, and the intensity of predicted root-mean-square WBV exposure in m/sec2. For any revealed WBV frequency that was associated with LBP, we constructed a multiple logistic regression model to identify the personal and vehicle characteristics associated with the presence of WBV peak within the indicated frequency range.

Jan 6, 2006

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

Maximising margins in today&apos;s competitive international commodity markets demands superior productivity. This requires more than simply selecting the best equipment. It requires efficient production and commercial processes together with management systems recognised as international best practice. This paper introduces an integrated way of working that includes management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It provides an improvement methodology that includes systematic involvement of people in true continuous improvement of processes for maximising productivity and safety while minimising costs. Even though the principles are proven in all industry sectors worldwide, they are not always used correctly. This paper provides examples of traditional performance measurement systems to show how managers miss opportunities to control and improve both production and supporting service processes. It also describes the basic methodology for correct use of the principles and provides examples of correct implementation of modem systems in mining. The charts from actual mining case studies will be elaborated upon in the conference presentation. This paper&apos;s main aim is to provide background material for the presentation by introducing integrated principles for building best practice management systems for superior productivity and safety - for higher margins.

Jan 1, 1996