Search Documents

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. TheZapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level.   However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy. In the developed countries, government policies for the development of mineral resources have been progressively eroded since the early 1970s. At the same time policies for the environment and for native land rights have generally been carried out in a way that has reduced access to minerals and increased the cost and risks for prospectors and developers (Hancock, 1995). Since the end of the Cold War, the lesser developed countries (LDCs) have introduced policies to attract investment in their mineral resources that remained undeveloped under previous unstable or hostile regimes. The increased attraction of these LDCs and the decreased attraction of the developed countries has caused many Australian and North American companies to outlay increasing proportions of their budgets and capital investment in the LDCs.   Significantly, LDC policies for environment protection do not discourage exploration and mine development, Surveys of the relative appeal of the LDCs and the traditional mining countries of the developed world, rate Chile, Argentina and Indonesia ahead of Australia and Canada in terms of risk, delays and ease of doing business (Australian Mining Monthly, February 1994).

Jan 1, 1995

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb-Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb-Zn ore was traced to apH effect. In the pH range, 9.5 to 11.0 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH)2 is suggested, the Fe- + ions being derived from superficial oxidation of pyrite in the ore. IntroductionGalena and sphalerite commonly occur together. A typical procedure, using xanthate collectors, is to float the galena first, at pH - 8, followed by flotation of sphalerite after activation with copper (II) sulphate at pH - 10 (to depress pyrite).Flotation tests following this procedure in an undergraduate laboratory course with a Pb-Zn ore from Polaris failed to achieve consistent selective flotation of galena. Occasionally a considerable amount of sphalerite, even though unactivated with CUSO4, floated. This was traced to accidentally high pH. A systematic study was carried out which revealed that sphalerite floated readily in the pH range 9.5 to 11.0 without activation by CuSO4 This paper describes the results of the study and discusses a possible mechanism of this flotation of sphalerite."

Jan 1, 1987

By Heber E. Peterson, Sill. Claude W.

"INTRODUCTION In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate. It seemed likely that the same general procedure could be used in determining semimicro quantities pf uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant in turn permits the use of the very stable indicator, ferroin; with its sharp color change and exactly reproducible blanks.Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Glen (5). The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months."

Jun 1, 1952

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By Jean-Sébastien Lambert, Serge Roberge

"At the end of 2014, Holcim Canada (Demix Aggregates Division) considered the possibility of drillingand blasting a big volume of rock in order to expose a high-quality limestone bench in one of their urbanarea quarries in Laval, Quebec (Canada). The project includes many challenges and has thus been qualified as a high-risk operation."

Jan 1, 2016

By Steve Meador

West Virginia's basic coal mining regulatory programs are not unique when compared to Federally approved programs implemented by other coal producing states. In fact, the language in The West Virginia Energy Act governing subsidence mirrors that written in the Federal Surface Mining Control and Reclamation Act as well as other states' statutes. Certain legal and administrative issues, how¬ever, combine to make West Virginia's regulation of surface subsidence a singular approach.

Jan 1, 1986

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

By D Matthews

With a brownfield project comes control integration challenges. The Khumani Iron Ore Mine’s second phase expansion posed a number of challenges as there was substantial brownfields work conducted. The fi rst phase was the compilation of the modifi ed process functional specifications for the project. The second phase was an audit on all of the operational sequences; this included a comparison between the SCADA sequences, sequential starts analysed from the historian data (with the potential for improvements made by the plant operators in manual start-ups) and what was proposed in the process functional specification. Differences, inclusions and missing equipment were highlighted. The third phase was the comparison of interlocking and control in the PLC with the updated process functional specification; this was done during the coding process. Running parallel to the three phases was the SCADA integration; tie-ins to the existing SCADA were conducted on maintenance days and shutdowns, in many instances with ‘dummy’ equipment to get the operational staff accustomed to the new interface. This paper details each of the phases, the success of this methodology as well as the pitfalls experienced.

Jul 11, 2011

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By G A. Wellwood

What do all iron ore mines have in common? Perfect production days! Yes, those harmonious 24-hour periods when the stars align and the daily output number rockets past the long-term average to hit new heights. While perfect days are always welcome, the focusing question iswas that just a ‘flash in the pan’ (due to a special cause) or an indication of the process’s capability (with clues to the common causes) which, if addressed, could make every day perfect? In the context of today’s operating environment, with the need to maximise productivity at minimum cost, it’s an important question.Investigations reveal that the throughput difference between a perfect production day and the average is often in the order of 40 per cent, and that bulk solids handling (BSH) system deficiencies are the largest (>50 per cent) class of lost opportunity. Root causes for underperformance of elements in BSH systems can often be traced back to the detailed design and even study-stage oversights. Essentially baked into the fabricated plant, operations are effectively forced to accept them at the point of practical completion and then deal with the consequences for the life of the mine. Subsequent normalisation of these defects in the planning process reduces visibility and hence the impetus for long-term solutions in favour of lower targets and quick fixes to keep the show on the road. On an industry wide basis the design processes and assumptions responsible for BSH system underperformance become enshrined as common practice and hence repeated across sites and organisations.In addition to making the case for action, practical steps that can be taken to help realise the significant productivity prize and avoid the problems in first place are provided.CITATION:Wellwood, G A, 2017. One perfect (production) day – a bulk solids handling perspective, in Proceedings Iron Ore 2017, pp 443–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009