Search Documents

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By M. J. Gregory

The Pebble Cu-Au-Mo deposit in southwest Alaska is one of the world's largest porphyry deposits. The western part of the deposit was discovered by Cominco America in 1987, who sold the project to Northern Dynasty Minerals Ltd., in 2001. Northern Dynasty discovered the high-grade eastern part of the deposit in 2004 and went into a 50:50 partnership with Anglo American PLC in 2007, forming the Pebble Limited Partnership (Lang et al., 2008). The Pebble Limited Partnership has continued to delineate the deposit through diamond drilling with the most recent resource estimate released in February 2010 (Pebble Limited Partnership, 2010). The Pebble deposit mineral resources comprise 5.94 billion tonnes of measured and indicated resources grading 0.78% Cu EQ, containing 55 billion pounds of copper, 67 million ounces of gold and 3.3 billion pounds of molybdenum. Also delineated are 4.84 billion tonnes of inferred mineral resources grading 0.53% Cu EQ, containing 25.6 billion pounds of copper, 40.4 million ounces of gold and 2.3 billion pounds of molybdenum (Pebble Limited Partnership, 2010). Resources are calculated using a 0.3% Cu EQ cutoff. GEOLOGY AND MINERALIZATION Deposit Geology The Pebble deposit is located in the Kahiltna terrane, between terminal strands of the north-east-striking Lake Clarke strike-slip fault. This fault represents an accretionary boundary and separates the Kahiltna terrane to the north-west from the Peninsular terrane to the south-east (Lang et al., 2008). The Pebble deposit represents a large magmatic-hydrothermal system centered on a group of 90 million year old porphyritic hornblende granodiorite intrusions. An east-west cross section through the southern part of the deposit (Figure 1A) shows the typical relationships between the various rock units which host sulfide mineralization. Sub-parallel ~96 million year old granodiorite and diorite sills were intruded into siltstones of the Jura-Cretaceous Kahiltna flysch. In the west, these sills were cut by a ~96 million year old alkalic intrusive complex composed of porphyritic monzonites and monzodiorites and related intrusion breccias (Bouley et al, 1995). The mineralized 90 million year old hornblende granodiorite intrusions cut all rock types and comprise four small stocks in the western part of the deposit and a larger pluton in the eastern part of the deposit. Recent deep drilling indicates that these intrusions coalesce at depth. The strongest porphyry-style mineralization is centered on the eastern granodiorite pluton and extends into the surrounding rock units (Figure 1A). The western half of the deposit crops out at surface, whereas the eastern side is un-conformably overlain by a cover sequence of Late Cretaceous to Eocene sedimentary and volcanic strata. The deposit was tilted 20º to the east during the Eocene.

Jan 1, 2012

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

By A. Whillier

The decisive action taken by mine managements in recent years has been the main factor in bringing about the present downward trend in mine fires. A better understanding of the fundamental factors that govern the ignition and spread of fires. obtained as a result of investigations into mine fires, has provided useful guidance to production personnel. Similar investigations into fire-fighting techniques have assisted the Rescue Training Service and mines to institute more effective fire-fighting techniques. Some of the more important findings of recent investigations in these areas are outlined.

Jan 1, 1981

By P. C. Holloway, A. Tshilombo, T. Xue, M. J. Collins, R. Lopetinsky, I. Mihaylov, I. M. Masters

The Voisey’s Bay deposit contains a trace amount of cadmium, which reports to solution during pressure leaching of the nickel concentrate at Vale’s Long Harbour Hydrometallurgy Plant, and must be removed to produce high quality nickel cathode. In 2006, Vale approached Sherritt Technologies to collaborate on the development of a process for removing cadmium to low levels (<1 mg/L) in the nickel raffinate. Following successful bench scale and pilot plant testing at Sherritt’s laboratories, the cadmium removal process was then moved through engineering and construction, culminating in the successful commissioning and startup of a cadmium removal circuit at the Long Harbour Hydrometallurgy Plant in 2017. This paper presents the results of this collaboration and the challenges that were encountered through each stage of development, as well as current results from operation of the commercial cadmium removal circuit. INTRODUCTION Vale’s Long Harbour Processing Plant, with a nameplate capacity of 50,000 t/y nickel, began operation in 2014. In addition to electrolytic nickel rounds, the plant also produces electrolytic cobalt rounds and copper cathode. The Long Harbour Processing Plant uses a unique hydrometallurgical process developed by Vale Base Metals Technology Centre, as shown in Figure 1, to treat a nickel sulphide concentrate produced at the Voisey’s Bay mine and mill located in northern Labrador (VBN concentrate) (Stevens et al., 2009).

Jan 1, 2019

The authors describe two stratiform intrusions within a two miles thick ophiolite belt, one of the many ophiolite (serpentine) belts of the eugeosynclinal sequences of the Kalgoorlie System (metamorphic age c.2700 million years). Unusually good evidence of gravitational differentiation involving cumulates for an Alpine type peridotite-gabbro intrusion has been obtained, in spite of modifications of the original igneous rocks imposed by regional metamorphism. Unmetamorphosed relics of cumulate rocks are a surprising feature of this occurIfence.&apos;fhe differentiation process reflected in the layered sequences is compared to that of the Stillwater Intrusion, Montana. Phase, cryptic and rhythmic layering are recognized. The economic significance of this study lies not only in the possibility of nickel mineralization in this ophiolite belt, but also in that much detailed information on the nature of these belts, which is difficult to obtain in the case of the more altered and sheared rocks of the belts carrying gold and nickel ore deposits nearby, is gathered from the Yilmia occurrences.

Jan 1, 1969

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By Michael J. Klishis

West Virginia University researchers examined risk and exposure in the roof bolter operator&apos;s job and developed approaches for preventing accidents and for evaluating system and human performances that may be appropriate as a general application to improve safety and efficiency in the industry. Using a microanalysis of accident data and underground observations, the researchers classified bolting injuries within one of four work routines: 1) drilling bolt holes; 2) bolt installation; 3) machine tramming, (re)positioning and setting the ATRS; and 4) general face preparation. Time and motion studies were then combined with injury data analysis to develop risk and severity indices, as well as a severity-weighted index that served to determine the degree of risk and exposure by work routine. More than two dozen bolting-related problems were identified as potential situations that could lead to injuries or expose workers during their job. Approaches to avoid these situations were suggested and then applied at six mining operations to evaluate specific problems in roof bolting operations. These suggestions encompassed the three E&apos;s of Safety (Engineering, Education, and Enforcement) and emphasized the analysis of worker behaviors that lead to human error accidents.

Jan 1, 1993

By Christopher P. O?Connor

Stereolithography is a well known rapid prototyping technique in the manufacturing sector. Essentially it is a three dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of Rapid Prototyping Techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models and in cases where it is decided to develop physical models, the process is time consuming based on simplified constructions. Rapid prototyping techniques (RPTs) such as stereolithography can facilitate engineers and geologists to quickly and with satisfactory accuracy to visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with the Department of Mines Research of Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs (e.g. stereolithography) to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems.

May 1, 2002

By Edward Capillon

THE problem of scrap is probably of greater importance inn the production of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of the base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is. not generally feasible to assay every shop remelt it follows that the possibilities of lost values are large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base, metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys.

Jan 1, 1930

By W. D. Maier, H. V. Eales

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. A lithological and geochemical study revealed significant lateral variation of the interval over 170 km of strike, from about 30 m at the Union Section to 220 m near Brits. The cumulates also become more evolved and leucocratic with distance from the Union Section both towards the NE (Amandelbult) and SE (Impala, Rustenburg and Brits). It is inferred that the persistent heat flux from a putative major feeder zone near the Union Section impaired deposition of felsic cumulates in the vicinity, delaying crystallisation of successive phases in parts of the chamber near the feeder. New influxes were therefore deposited on a footwall of varying thickness and lithology in response to different degrees of crystallisation and accumulation along strike. The development of cyclic units of chromitite, harzburgite, pyroxenite, norite and anorthosite was interrupted at different stages in different parts of the chamber

Apr 1, 1994

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey&apos;s success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987