Search Documents

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By A N. Gupta, C Joginadham, P Shiva Shankar

Cast boosters made with pentaerythritol tetranitrate(PETN) and trinitro toluene(TNT) give high velocities of detonation and are sensitive to initiation even under high pressures. However, the manufacture of the same involves heating of TNT to its melting temperature and mixing of dry PETN in it.

Jan 1, 1996

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By M. Ounpuu

"Gold, because of low head grade and recovery, is usually of minor importance in the economics of base metal flotation mills. Because of the above little metallurgical attention is usually provided to gold in these mills. But collectively, the gold losses can be significant. For instance, Noranda presently has interest in 13 base metal flotation mills with a collective gold recovery of only 50%. Gold losses are in the order of 150.000 oz per year!The Noranda Technology Centre, in cooperation with Noranda's milling operations, has been investigating the potential of gravity concentration of gold from base metal flotation mills. This paper outlines the pilot and plant testing conducted at three operations with distinctly different ore types; porphyry copper, complex massive sulphide and polymetallic semi-massive sulphide. Testing has been with the Knelson Concentrator which has proven to successfully recover fine gold in a simple, trouble free circuit. Discussion of issues which have risen from the testwork is included. INTRODUCTIONGold, because of low head grade and recovery, is usually of minor importance in the economics of poly-metallic base metal ores. TABLE I presents gold heads and recovery for some of Noranda's base metal mills. It should be noted that the stated recoveries are to payable concentrates, but does not reflect the actual payable gold recovery which in cases is significantly lower. Noranda's average gold recovery into a gold payable concentrates is about 45%. This equates to a collective loss in the order of $57 MM per year of gold"

Jan 1, 1992

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007