Search Documents

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By G W. Heyes, P J. Guy

Investigations were undertaken to assess the suitability of CSIROflotation methods for improving the efficiency of separation of heavyminerals in the monazite circuit at the Westralian Sands Limitedoperations at Capel, Western Australia. Flotation work was conducted on two plant samples. The first was a high-titanium product containing considerable amounts of zircon and silica as quartz and aluminosilicates, and the second was a low monazite/zircon material containing high levels of silica. A three-stage process including reverse flotation was developed totreat the first sample. In this process monazite, zircon, quartz, andaluminosilicates were selectively concentrated by flotation and screening to produce a titanium-rich product. In the first stage, an acid amine float, monazite, zircon, and some non-zircon silica were recovered and in the second stage, an alkaline amine float using a fluoride activator, more quartz and staurolite were floated. The titanium minerals were thus concentrated in the unfloated fraction. In the third stage, the titanium-rich flotation tail was screened at 250 ¦m to remove the remaining coarse aluminosilicates. In a single pass, the three-stage process yielded a TiO2 recovery of 64.0 per cent with the titanium-rich product assaying 70.3 per cent TiO2.

Jan 1, 2001

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By Eun-young Kim

Electrogenerated chlorine leaching of waste printed circuit boards was investigated in hydrochloric acid solutions. The pulverized printed circuit board contained about 37.6% of metal component, in which copper was about 83.6%. The leaching rate of copper was greatly affected by current density and agitation speed. The leaching of copper up to 98% was achieved at 20 mA/cm2, 50?, 180 minutes, and 600 rpm in 1M HCl solution. Increasing agitation and lowering current density enhanced utilization efficiency of electrogenerated chlorine. Leaching of copper was suppressed at initial stage, while the minor metal elements, such as aluminum, lead, and tin, were dominantly leached out.

Jan 1, 2006

Recently, work was carried out by the Shotcrete Working Group to study anisotropy in steel fibre reinforced shotcrete using strain-controlled, compressive strength testing methods. The shotcrete materials used and specimen preparation procedures as well as testing methods are described. The test results are discussed and it is concluded that, because of the anisotropic nature of fibre reinforced shotcrete, it may be worthwhile investigating the degree of such anisotropy in practice using strain-controlled, strength testing techniques.

Jan 1, 2001

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By Rainer Kahrger

During the last decade, advances were made in solvent extraction/electrowinning (SX/EW) technologies. Combined with heap leaching, these technologies made it viable to exploit large, low-grade oxide copper deposits. The El Abra Mine is a good example for such a deposit. The deposit is situated in northern Chile at an elevation of about 4,000 m (14,000ft), 70 km (45 miles) north of Calama. Codelco sold 51% of the El Abra to Cyprus Minerals in June 1994, with Codelco retaining the balance. In 1993, Cyprus and the engineer on the project began discussions withinternational companies regarding the materials-handling system requiredfor the project. These early discussions were considered critical for this fast-track project.

Jan 1, 1996

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Neil E. Ryan

Because of their chemical reactivity and affinity for oxygen, rare-earth elements are difficult to extract, and due to their close chemical similarity, it is an exacting task to separate one from the other. Nevertheless, these same characteristics can be used to benefit other metals by enhancing their resistance to high-temperture oxidation/corrosion and by inhibiting their corrosion in aqueous environments. This paper gives an overview of the use of rare-earths: [a] as alloy additions, [b] in coatings, and [c] when added to hostile environments, to retard rates of high- temperature oxidation and inhibit aqueous corrosion.

Jan 1, 1992

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By George S. Rice

Potash is riot only an important ingredient in the manufacture of many products of modern industry, such as chemicals, explosives, medicines, paints, soap, matches, glass, paper, aniline dyes, bleaching agents, and a host of others, but is indispensable in agriculture. Justus von Liebig is credited with being the first to discover, about 1858, that potash salts in the soil constitute an essential plant food which is not replaced by nature when exhausted through continued cultivation, that this exhaustion results in a decreasing yield of crops, and that the virgin productivity of the soil may be restored, and indeed even increased, by the addition of suitable potash fertilizers. The fact is now well established that wherever intensive cultivation is employed, whether for the raising of cereals, cotton, tobacco, fruit, or garden truck, the replenishment of the potash content of the soil is essential to the maintenance of production. Hence potash is of primary importance in modern life, not only for the economic welfare of industry but for the production of valuable raw materials and the very food supply of the nation itself. SOURCES OF POTASH The main sources of commercial potash are: (1) The solid deposits of soluble potash minerals, such as carnallite, sylvinite, and kainite; (2) sea water, brines, and salt-lake deposits containing appreciable amounts of potash salts associated with sodium salts; (3) vegetable substances, such as wood ashes, bee sugar residues, seaweed, and sunflower stalks; (4) animal material, such as wool washings; (5) products resulting from the decay of organic nitrogenous matter, such as Indian niter; (6) dust in flue gases from cement kilns or in the top gases of iron blast furnaces; and (7) insoluble potash minerals, including alunite, feldspar, leucite, muscovite, and glauconite, all of which contain a considerable quantity of potash.1

Jan 1, 1927

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003