Search Documents

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By J L. Mauk

The Gladstone Hill area hosts epithermal veins similar to those at Martha Hill, which is less than one kilometre away. There are several vein types in the Gladstone Hill area including (1) pyrite-marcasite, (2) quartz, (3) base metal sulfide, and (4) calcite. Pyrite veinlets formed first, whereas the quartz and carbonate veins formed later. The base metal sulfide vein occurs at depth and is predominantly comprised of quartz and chlorite intimately intergrown with pyrite, sphalerite, galena, and rare chalcopyrite. Platy calcite and massive calcite veinlets were the last vein types to form. Several vein textures occur in the Gladstone Hill area, including colloform and crustiform banding, lattice-bladed, zonal, comb, massive and feathery textures. Crustiform banded veins are the dominant texture and contain variable gold-silver grades. Colloform banded veins consist of ubiquitous quartz and minor chalcedony with gold grades as high as 60 g/t. The lattice-bladed texture forms from the deposition of calcite, which has been replaced in many samples by quartz, indicating that boiling and later cooling has taken place. Unreplaced platy calcite only occurs at deeper levels (>300 m). Zonal and comb textures are preserved in quartz and late-stage amethyst veins. Feathery textures within quartz are commonly associated with breccias and some colloform banding, and with significant Au-Ag grades.   The homogenisation temperatures (Th) of primary and secondary inclusions in quartz, amethyst and platy calcite range from 166 to 274¦C, with salinities <1.3 wt% NaCI equiv. The presence of vapor-dominated inclusions and primary fluid inclusions in platy calcite suggests that boiling occurred intermittently throughout deposition. The veins formed under a relatively flat lying paleowater table that occurred 280 - 300 m above sea level. The fluids involved in vein formation were alkali chloride in composition and low in CO2.

Jan 1, 2001

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

Misiman society is matrilineal and despite relatively long contact with Europeans and mining, it retains its traditional consensus style of decision making. Many Misimans at least understand English, and this has encouraged comfortable communication between the people and the company (Misima Mines Pty Limited). Company care in monitoring the environment (mostly using Misiman staff), its policy of maintaining a largely Misiman workforce, and its emphasis on training and safety, have all created an environment compatible with Misiman society. In addition, the company has constructed and/or upgraded community facilities such as the airstrip, roads, the health centre, police station and schools, and has actively promoted local business endeavours. All these initiatives have been accomplished by constant dialogue with the largely Misiman workforce, and with the Misiman people, both before and during implementation. Constant, careful communication, using traditional Misiman consensus methods, appears to be the key to continued community acceptance of the project.

Jan 1, 1991

By Pedro Lilienfeld

This report presents a design and cost investigation for several alternative versions of a field-worthy mining machine-mounted respirable dust monitor. Three main design variations are considered: (a) light scattering sensing, (b) Beta-filter tape sensing, and (c) a combination of the two preceeding methods. Eventual instrument production coats as a function of design complexity are tabulated. Cost estimates for the development and field testing of field-worthy prototypes are also presented. A general discussion on the technical aspects of these design alternatives is included following a modular-hierarchical approach of progressive complexity. The technical background to this report has been provided by the experience and results derived from the work performed under U.S. Bureau of Mines Contracts Nos. H0166097 and H0377092.

Jan 1, 1980

By John L. Thames

The benefits of water harvesting as an alternative to conventional reclamation were demonstrated on the Peabody Coal mines in Northeast Arizona. The project produced food crops for four years, and demonstrated that a catchment/crop area ratio of about 2.5:1 was sufficient to obtain sufficient water from the 11 inch annual precipitation to produce garden and fruit varieties in quantities equal to or exceeding national production averages. The economic returns exceeded those of the conventional practice of returning the mine area to rangeland by at least ten fold. Subsidence of the regraded spoil was the only major problem in maintaining the system. Although, water harvesting systems have the potential of providing high economic returns and greater social benefits, as demonstrated by this project they are presently at variance with the strip mining regulation.

Jan 1, 1984

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Thomas E. Lobb, Harry C. Verakis

This article examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are:(a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f)training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.