Search Documents

By Sofoulis J

In the Archaean of the Kalgoorlie-Norseman area, the layered rocks have been subdivided into two sequences, both containing basic igneous rocks and sediments. The lower sequence is distinguished by the presence of acid volcanic flows and large acid sills. The upper sequence is unconformable on the lower one.In some areas, clastic sediments become coarser and pass into conglomerates. Th:s passage is accompanied by thinning of the beds.These features and their distribution suggest a basin of subsidence flanked by areas of shore-line conditions.Repeated igneous activity, including vulcanism, has occurred along the flanks of this basin. These different igneous and sedimentary environments have played an important part in the primary distribution of metals.A chronology of all basic and acid igneous activity, as well as sedimentat:on, has been established for the Precambrian of this area.INTRODUCTIONThe subdivision of Archaean rocks into those of basic igneous or of sedimentary origin has formed the basis for the nomenclature appearing in past literature. These subdivisions were distinguished as greenstones (predominantly basic igneous rocks) and whitestones (predominantly sediments), and it was generally accepted that the greenstones were stratigraphically lower in the sequence than the whitestones.Recent studies show that, between Kalgoorlie and Norseman, basic igneous rocks interfinger with and pass laterally to sediments, and that basic volcanic rocks occur at different stratigraphic levels. Younger Precambrian. units are also...

Jan 1, 1965

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By Leroy E. Schulze

A review of development and a reevaluation of uses of the hydraulic air compressor are suggested by the constant changes in technology, which frequently make an old art valuable in solving current problems. Contacts with research workers in various branches of engineering indicate that this older method of producing compressed air may not be familiar to some or that its salient features might be useful in solving problems involving uses of compressed air. Briefly, a hydraulic air compressor may be described as an inverted siphon, consisting of an intake head where water and air are mingled, followed by a gravity-fall tube in which air is intimately mixed with the water and is compressed as the water pressure increases during the fall down the tube, then a separating, or stilling, chamber in which air bubbles rise to the surface of the water and collect in the upper portion of the chamber at a pressure equal to the weterhead maintained by the height of water in the discharge leg of the circuit. The water, which now contains only the fraction of air that has gone into solution, passes out of the separating chamber and rises up the discharge leg to the surface, which is, of course, at some suitable distance below the level of the intake. Present-day applications include (1) utilizing low hydraulic heads, which otherwise have little commercial values; (2) utilizing low hydraulic heads in reclamation work to supply compressed air, or in some instances to produce a small suction, for air-lift pumping (or for operation of air motors), with minimum attendance and without need for electric power; (3) utilizing medium heads, as at dam and lock installations, to produce compressed air for pneumatic operation of airlifts, gates, valves, and rubber gate seals; (4) utilizing underground waters, as in mines, to produce compressed air for general mine use; (5) using this method of isothermal compression of air in combination with standard compressors wherever hydraulic head is available, thereby securing the advantages of low-temperature intake to the mechanical compressors and reduction of moisture content below that of atmospheric air; (6) development of large air supply at pressures up to 150 p.s.i.g., which, after performing work in reciprocating or centrifugal expansion cylinders, is available at temperatures approximating -50° F. Possibilities in freezing and reheating should be mentioned which may prove economical for obtaining uniformly dry air for process work, wind-tunnel tests, or large air-conditioning installations, such as ventilation of underwater traffic tunnels, and may be economic for supply of supercharged air to gas-turbine plants.

Jan 1, 1954

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By M. Baumann

Introduction Gold Quarry is one of the largest gold deposits in Nevada, located along the Carlin Trend, approximately seven miles north of Carlin, NV. Owned and operated by Newmont Mining Corporation, as of December 31, 2005, Gold Quarry had produced over 13 million ounces of gold. Multiple simulations were constructed for gold and metallurgical variables using the Stepwise Conditional Transformation method. Analyses of these simulations have been used for a variety of purposes, including an assessment of uncertainty with various ore types. This assessment provides insight for improved modeling and reconciliation. Geological Framework Gold Quarry is a large, low-grade disseminated gold deposit hosted in Silurian-Devonian aged sediments at the Chukar/Alunite-Good Hope fault intersection. Gold bearing hydrothermal fluids appear to have migrated upwards along the Chukar/Alunite and Deep Sulfide Feeder faults and then moved outward along favorable stratigraphic horizons and structural intersections.

Jan 1, 2007

By William M. Gleason

When SME’s 2006 Arizona Conference convened in December at the Hilton El Conquistador Resort in Tucson, AZ, there was considerable excitement among the 387 attendees. There was a noticeable buzz surrounding the progress of Phelps Dodge’s Safford copper mine in southern Arizona, one of the first new major copper mines to be permitted in more than 30 years in the United States. There were also plenty of good feelings about the mining industry in general. Commodity prices remained high and with no signs of a slowdown in the immediate future. Things were good in Arizona. But there were also cautionary tones at the conference and the Mining Foundation of the Southwest banquet that preceded it.

Jan 1, 2007

By Dan A. Brown

The New Mississippi River Bridge (MRB) employed conventional design-bid-build procurement, but the bidding process included the opportunity for pre-qualified bidders to develop and propose confidential Alternative Technical Concepts (ATC?s) for evaluation and approval in advance of bidding. The ATC process provides a mechanism for value-engineering prior to bid, with incentives and opportunities for both the owner and the bidding contractor. The contract described in this paper is for the river bridge composed of a cable-stayed crossing with two pylons and the anchor piers on each side of the river. The Massman-Traylor-Alberici (MTA) team developed a re-designed foundation system for the main pylon and anchor foundations which utilizes their equipment and experience along with field load test measurements to optimize the foundations. The paper describes the experience with the use of the pre-bid ATC process on the project from the perspective of the bidder, and outlines some of the benefits and limitations of this concept with respect to foundation design and construction. Some keys for success are identified and impediments to the effective implementation of the process are described.

Jan 1, 2011

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By Charles F. Coleman

Kinetics studies and other rate measurements are reviewed in the amine extraction of uranium and of some other related and associated metal ions. Equilibration' is relatively fast in the uranium sulfate systems most important to uranium-hydrometallurgy. Significantly slow; equilibration-has ' been encountered' in some other systems. Most of the recorded rate information, both qualitative and quantitative; has come from exploratory and, process-development development work, while some kinetics studies have been directed specifically toward elucidation of, extraction mechanisms. In contrast to some other extraction systems, relatively little attention has been given to the kinetics of uranium extraction by amines. This is because investigators have not been troubled by slow extractions. Instead, when rate limitations have been of concern in amine extraction (Amex) process developments, they have been mainly from slow phase disengagement rather than from slow equilibration. Nevertheless, taking uranium together with several other elements that are closely related to it or associated with it in typical processes, a considerable body of rate information has been recorded.

Jan 1, 1979

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By Steve Kral

A near-record crowd of mining history enthusiasts made the trip to Leadville, CO in September to attend the National Mining Hall of Fame and Museum’s 19th induction banquet. Dressed in Victorian garb, black tie tuxedos and formal gowns, the 268 people honored four distinguished men who made a lasting impact on the U.S. mining industry. They joined 188 other inductees. The first induction banquet took place in 1988, with about 500 people attending.

Jan 1, 2007

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Michael Taylor, Thomas W. BoBo

Currently two of the most important characteristics of construction aggregates are (a) the particle size distribution (psd) and (b) the “shape” of the aggregate particles. The long established test methods and standards for these properties require substantial resources and most suppliers can take samples and conduct tests at intervals measured in days (psd) or even months (shape). Furthermore these tests require time: so the results are available only after material has been stockpiled or shipped. In the rare cases where problems are found the out-of-spec material has often been shipped to points unknown. There are substantial advantages to be obtained if the psd and other geometrical properties could be obtained from the material as it moves through the production processes and if the results could be reported back within seconds or minutes to Plant Control Managers. This paper describes a single on-line system used to evaluate production of crushed material in a production quarry. The system consists of an enclosure (containing the camera and lighting etc.) mounted over a production belt. Images are fed by fiber optic cable to a nearby control room where the data are analyzed; stored; displayed; and made available for integration into a process control system. Numerous forms of display can be created according to the needs of the producer. Once programmed by an automation engineer all functions of operation are fully automated. The system has permitted over 400 tests per hour with a feed back time less than 2 seconds. Sufficient geometrical measurements are made so that many different “shape” factors can be computed on a similar time scale. The paper summarizes the results from approximately 100 shifts of about 8 hours each and compares the imaging method with the current standard hand methods. Study of the data generated showed that, when combined with additional plant information, the system can be used to generate additional useful control information.

Jan 1, 2005

By Fredrick D. Palmer

The World is Turning to Coal Peabody?s View ?We believe the world is increasingly energy-short, led by unprecedented demand from population centers and economic hubs in Asia, the Middle East and South America ?This occurs as:?Traditional energy sources are clearly constrained, requiring coal-based alternatives?Energy-rich nations leverage political gain from their assets, and nations urgently look to improve energy security ?In this environment:?Oil, coal and gas face a greater long-term convergence, ?Coal?s traditional regionalized nature becomes global, and ?Coal?s compact energy form becomes an attractive source for liquids and substitute natural gas ?The world is blessed with an abundance of coal to help meet all human energy needs

Jan 1, 2008

By Doris M. Hyde

Mineral output and trade in the Central American countries were directly or indirectly affected by the sometimes violent civil unrest and recessionary economic developments that have pervaded the region for several years. Central American countries found their foreign exchange export earnings and traditional market areas shrinking while essential import costs were rising. Restricted spending measures were adopted by governments and private industries. Domestic investment funds for mineral development and exploration projects were among the first casualties of these austere budgetary measures, especially since weak demand and depressed mineral prices diminished the probability of a favorable cost-benefit ratio. The lack of physical security and political stability also discouraged private foreign investment. The United States Congress enacted the Caribbean Basin Economic Recovery Act of 1983 (19 U.S.C. 2702), more popularly known as the Caribbean Basin Initiative (CBI). This legislation was designed to stimulate economic recovery and promote economic development by increasing private investment and trade in the Caribbean Basin countries. The act provided for the elimination of U.S. duties on most trade items imported directly from eligible Caribbean countries, provided at least 35% of the product value originated in the region. The financial assistance components of the CBI were to be supportive of the basin's private sector as well as assist general economic stabilization programs.

Jan 1, 1985

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008