Search Documents

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By C. M. Wright

Siendo la veta principal San Cristóbal, una de las estructuras que atraviesan el Anticlinal Chumpe en la provincia de Yauli, su explotación ha sido limitada a las rocas volcánicas y filitas en el flanco sur-oeste del anticlinal. Por tal motivo, el texto señala que el análisis de la distribución de los metales y minerales dentro de la veta, revela un zoneamiento horizontal bien definido, que es compatible con el origen de las soluciones hidrotermales en el centro del anticlinal. Asimismo, este estudio cuantitativo determina las características de las partes ricas de la veta, trazando líneas de contornos de los cuatro tipos de metal en secciones longitudinales, como los controles de la distribución de metal y relaciona las áreas ricas de la veta con su medio geológico. De otro lado, en San Cristóbal, la distribución del metal presenta una característica zonal donde la paragénesis y el zoneamiento están íntimamente relacionados. Concluyéndose que con la aplicación de los resultados de este estudio, se permitirá una mejor exploración y desarrollo de las áreas ricas de la Veta Principal San Cristóbal y se proporcionará una guía útil para la exploración y desarrollo de vetas paralelas en esta área.

Aug 20, 1963

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By O. Matwijenko

"1. IntroductionThe Falconbridge Owl Creek open pit gold mine is located 17 km northeast of Timmins and 2.5 km west of the Kidd Creek metallurgical site. Diamond drilling first commenced in 1964 with open pit production commencing in 1982. Other operations within close proximity are the Canamax-Pamour Bell Creek Mine and the Falconbridge Hoyle Pond Mine.Since 1982, 1,216,000 tonnes assaying 4.5 g/t have been processed in six concentrators. This paper summarizes the metallurgy achieved with special emphasis on some of the unique problems encountered in the processing of this refractory ore.2. GeologyThe Owl Creek deposit, located 3 km north of the Porcupine-Destor fault is in easterly trending carbonaceously altered volcanic and sedimentary rocks. The deposit strikes east and dips steeply north.The ore body can be best described as a wedge shaped sandwich of volcanic basalt between the surrounding sedimentary greywacke. The north and south volcanic-sedimentary interfaces are marked by graphitic zones. The south graphitic contact is more continuous with its thickness varying from 5 m to 20 m as compared to 0.5 m to 3 m to the north. Quartz veins occur throughout the deposit with a predominant vein running along the south contact where it is characterized by numerous graphitic inclusions. Some veins carrying gold values intrude into the sediments in the north. With depth the sedimentary and volcanic zones taper while the quartz-graphitic zones appear to become more dominant."

Jan 1, 1988

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By Edgardo Torres Hernández

El Proyecto Optimización de Ángulos de Taludes en Explotación de Minas es un proyecto desarrollados por E-Mining Technology (EMT), socio estratégico de Prodimin en Perú, para Codelco Chile en uno de sus yacimientos del Norte de Chile. El desarrollo de este proyecto estuvo enmarcado en el Programa de Proveedores de Clase Mundial; programa que tiene como misión desarrollar un sector de proveedores intensivo en conocimiento, mediante la generación de soluciones tecnológicas empujadas desde la demanda de la minería y desde la propuesta del sector de proveedores que puedan ser escaladas a otros sectores y mercados.

Sep 1, 2017

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

By Sashir Estela De la Cruz

Actualmente la informática como herramienta aplicada al sector minero nacional, es importante -en tanto su empleo adecuado y racional implica alcanzar los objetivos planteados en forma más rápida y con mayor calidad. En este sentido, el presente texto describe el sistema informático que genera soporte al trabajo de modelamiento geológico para la estimación de reservas mineras, de forma que reduce el tiempo y personal empleado en dicha labor. Este sistema se divide en dos partes: estadístico y gráfico y determina la explotación de un prospecto de yacimiento minero.

May 25, 1998

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006