Search Documents

By John Kazakoff, Andrew Mortimore

"Production at the remote Kumtor Gold Mine in Kyrgyzstan commenced on schedule in December 1996.The ore mined during the first few months of 1997 from the upper benches of the pit did not produce the results predicted by the feasibility study. Low metallurgical recoveries experienced at the time were cause for great concern.It soon became clear the recovery difficulties centred around the preg robbing nature of the ore.Procedures were developed to selectively stockpile highly carbonaceous low recovery ore types. Testing methods were developed in the mill to quante the preg robbing activity of the ore. Preg robbing masking agents were added to the process to reduce the preg robbing activity of the ore.The importance of coconut carbon activity relative to the preg robbing activity of the ore was realized. Every aspect of the performance of coconut carbon in circuit was evaluated and optimized to improve carbon activity.Mineralogical analyses were completed defining the deportment of gold in ore and process tailingsBy year end the recovery difficulties had been overcome and plant design production had been achieved. Process improvements continue through 1998."

Jan 1, 1999

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Roy H. Poston

This paper sets forth the mode of ore occurrence, characteristics of ore and country rocks, methods of exploration, development, and. ore extraction, and the costs of underground operation at No. 8 mine of the St. Louis Smelting and Refining Works of the National Lead Co. located near the southern extremity of the Southeast Missouri lead district. The author acknowledges the assistance of E. T. Campbell, geologist, in the preparation of the paragraphs on the geology of the ores. HISTORY The first record of mining in St. Francois County, Mo., concerns more or less shallow semisurface "diggings" which were worked about the year 174-2. In 1864, however, the discovery of the disseminated deposits, the present source of lead, was made on property near the town of Bone Terre. Winslow has estimated the lead-ore production in this county prior to 1869 to be 59,526 tons.3

Jan 1, 1929

Market confidence is on the rise and industry leaders turning toward the vast and diverse region of Latin America are faced with abundant, yet daunting, opportunity. From the iron orebodies of Brazil to the renowned copper mines of northern Chile, drilling teams in Latin America are often faced with abrasive, broken ground. These types of ground conditions tear up coring bits rapidly, making it extremely difficult for even the most seasoned drilling teams to maintain effective productivity. The drilling challenges faced in this rich and opportune region are being met today by advanced coring technology, bringing with it the potential for increased productivity in Latin American mineral exploration.

Jan 3, 2010

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By M. Ahrens, J. Gonser

Gearless mill drives are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as their advantages compared to other drive solutions. Due to the variable speed operation the grinding process can be optimized for ores with varying grinding properties. This leads to significant optimization potential for the plant design as well as for its operation. Furthermore, energy and cost savings due to optimized operation, high system efficiency and high system availability are shown.

Jan 1, 2007

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By Christian Flores

El proceso que se enfrentó en Tambomayo tuvo su principal complejidad en llevar un proyecto en etapa de exploración hacia la construcción de una a unidad productiva la cual permita obtener resultados económicos y trabajar con altos estándares operacionales en el que prime la seguridad y un buen clima laboral, acompañado al hecho de que la empresa cuenta con una cultura operativa tradicional, lo que género que las principales dificultades para la toma de decisiones es que se tengan que ir derrumbando paradigmas operacionales y de esta manera ser un agente de cambio para el logro de los objetivos.

Sep 1, 2017

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By Jon Y. Kaneshiro, Sean A. Menge, M. Luis Piek, Brian Barker

The Lake Hodges to Olivenhain Pipeline project is part of a 40-megawatt pumped storage project linking two reservoirs as part of the San Diego County Water Authority’s $939 million Emergency Storage Project. Seeking to expedite project completion, the project was advertised as Design-Build, a first for the owner. Awarded to Kiewit Pacific with Parsons as designer, the 1,750m (5,700ft) long, 4.25-m (14 ft) horseshoe tunnel was excavated with conventional drill-and-shoot technique. The mining method was well suited to deal with the shear zones, the very abrasive rock, and 13.3% and19.6% grades. At the apex of the alignment, a 60m (200ft) by 3.6m (12ft) diameter raisebore shaft with surge chamber to protect against pump malfunction was constructed. Upon completion of mining, the tunnel was lined with a 3m (10 ft) diameter high strength steel pipe. Scheduled to come on-line by January 1, 2008, the Lake Hodges to Olivenhain pumped storage project is valued at $108 million, delivering a reliable source of water in emergency situations and electricity-generating capability to meet the growing demands of the San Diego region.

Jan 1, 2007

By R. R. Allen

[The utilization of Western coals and lignite is a continuing study of the Bureau of Mines, and storage of these fuels is of paramount importance. Since the seasonal demand for coal in the Western States triples between the summer and winter months, successful storage of these low-rank fuels would tend to level out this variation and should reduce fuel costs. The time is rapidly approaching when the West Coast States, particularly California, will annually import several million tons of coal from the Rocky Mountain States for additional power production. This will necessitate storage of large quantities of coal, and it is thefore important to develop experience in such storage. Dry surface storage, by virtue of its flexibility and low cost, is particularly adapted to the stockpiling of large quantities of coal. This report will, therefore be primarily concerned with such storage. Inasmuch as the problems of dry, open-pit storage are quite similar to those of surface stockpiling, experiences in pit storage will be discussed briefly. Although spontaneous combustion is a hazard in storing coal, experience has proved that heats can be avoided by proper stockpiling procedures. The purpose of this report is to show that the most reactive coals can be stored satisfactorily on the surface by avoiding segregation and by thorough compaction.]

Jan 1, 1954

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989