Search Documents

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

By W. M. Mark

This investigation was undertaken to develop methods to improve the quality of titanium sponge produced by the Bureau of Mines modification of the Kroll magnesium reduction process. Research revealed that by systematic elimination of detrimental impurities introduced with the raw materials and by improved handling and processing techniques, high-quality ductile titanium with a hardness of less than 110 B.h.n. (Brinell hardness number) can be produced consistently. This improvement was accomplished by helium (or argon) stripping of residual atmospheric and other dissolved gases from the titanic chloride, preliminary dehydration of crude titanium sponge, and careful regulation of the titanium tetrachloride (TiC14) feed rate to the reactors.

Jan 1, 1960

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

By M. A. Meyer

Underground mining accidents in the USA in recent times have prompted the Mine Safety and Health Administration (MSHA) to review emergency and tracking systems for underground mines. Several communication and tracking systems are available on the market and various systems have been installed in mines around the world. In addition, MSHA?s standard on Diesel Particulate Matter (DPM) requires mines to comply with the final PEL of 160µg/m3 by May 20, 2008. Barrick Goldstrike Mines Inc., Underground Division, has been in operation since 1995 and an extensive control and monitoring network, and a leaky feeder voice network is in place. Enhancements to the communication and control system are currently being implemented to include a PED emergency notification system, wireless LAN with tracking of personnel and equipment in the mine, and a ventilation control system that will use the tracking information and ventilation data to automate much of the mine ventilation system. Expected benefits from such a system would be enhanced communication with miners, emergency notification, location of miners and equipment, energy savings, improved ventilation control, and improved atmospheric conditions in the mine including reduction of diesel particulate matter (DPM).

Jan 1, 2009

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By J B. Taylor

Geographic Information Systems (GIS) are being increasingly used by the mineral exploration industry in the search for new ore deposits. A mineral exploration GIS links geological and geophysical data by virtue of their geographic location in a digital map setting. Geological and geophysical data are categorised into a number of themes or layers within a mineral exploration GIS. These layers may include polygonal information such as rock type and tenements, line information such as faults and fold axes, point information such as mines and mineral occurences, and images such as gridded geochemistry and aeromagnetics. A mineral exploration GIS is a powerful tool to help the explorationist comprehend the spatial associations and interrelationships of his/her data. These spatial associations can be integrated with a mineral genesis model, to create a mineral prospectivity map to more effectively target exploration. Arguably a competent geologist who has a good understanding of the genesis of the local ore deposit types and knows their local geology backwards could intuitively derive a mineral prospectivity map. However, in an era of rapid data accumulation from many different disciplines, the ability to assimilate and understand is a huge task for any individual. A mineral exploration GIS enables the explorationist to spend more time analysing data and testing ideas, rather than finding and manipulating data into compatible formats.

Jan 1, 1994

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By C V. B Cunningham

The assessment of blasting results under production conditions is extremely difficult. As a result, it can take months or years to establish objective and valid estimates of explosive performance in achieving rockbreaking goals. This fundamental problem often results in decisions related to the manufacture, marketing, purchase and use of explosives being largely swayed by calculated energies from detonation codes. However, these codes are by no means standardised. Different energies are given by different codes because these employ varying combinations of fundamental science and empiricism. After a basic review of code operation, important guidelines to dependability are given with reference to ICI’S state-of-the-art codes IDEX and CPEX. Distinctions are drawn between Ideal, Non-Ideal and Blasting Codes. Concepts of explosive energy are discussed in brief.

Jan 1, 1991

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

Today?s Topics ? Data to decision value chain ? Practical Considerations ? Example ? Before / After DSS ? Quick Decision Support Demo Practical Considerations ? More data is not necessarily better ? Organization and process silos ? Good vs. ?optimal?, but impractical Solutions

May 1, 2008

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

By John H. Soule

Although known since 1902 , the Capitan iron deposits have not been mined mainly because of the low grade of the ore . A small amount of exploratory work carried on at an early date was reported . C. E. Johnson , district engineer of the Bureau of lines for New, Mexico , visited this propert , and as a result of preliminary sampling and mapping by the Bureau3/ and the Federal Géological Survey , an exploratory project was conducted during March , April , and liay 1944. Further mapping and logging of the vagon -drill samples was done by V. C. Kelly , geologist , of the Survey .

Mar 1, 1947

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963