Search Documents

By H Peiming, W Sakurai, Y Matsuhisa, H Shimazaki, Y Fukahori

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skarn Pb-Zn deposits in the Kamioka mining district, centralJapan, where the wall rocks consist of heterogeneous rock units. The results (d18OSMOW of -1.1 to +17.3ë and d13CPDB of -5.0 to +4.8ë for limestones, and d18OSMOW of -0.8 to +12.5ë for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (18O and 13C) toward the centre of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralisation. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to-rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralisation had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360 m.

Jan 1, 1995

By Jerry F. Parola

In current practice, pile foundation design is based on a general under-standing of pile-soil interaction during installation and superstructure-pile-soil interaction after construction. The pile design is a reflection of experience, precedent and judgment for normal piling practice of working load capacities up to approximately 100 tons with corresponding ultimate capacities up to 200 tons. For higher capacity piles, pile design is even less predictable. In particular, the feasibility of pile installation is an important design consideration that must be given the proper attention. An installation capability that is not given the required emphasis can cause unnecessary problems.

Jan 1, 1986

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

Process Study on Some Ag-Cu-Pb-Zn Polymetallic Ore in South China

Sep 13, 2010

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 3, 1987

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By A. Krause

Shovel-truck systems for loading and hauling material in open pit mines are now routinely analysed using simulation models or off-the-shelf simulation software packages, which can be very expensive for once-off or occasional use. The simulation models invariably produce different estimations of fleet sizes due to their differing estimations of cycle time. No single model or package can accurately estimate the required fleet size because the fleet operating parameters are characteristically random and dynamic. In order to improve confidence in sizing the fleet for a mining project, at least two estimation models should be used. This paper demonstrates that the Machine Repair Model can be modified and used as a model for estimating truck fleet size in an open pit shovel-truck system. The modified Machine Repair Model is first applied to a virtual open pit mine case study. The results compare favourably to output from other estimation models using the same input parameters for the virtual mine. The modified Machine Repair Model is further applied to an existing open pit coal operation, the Kwagga Section of Optimum Colliery as a case study. Again the results confirm those obtained from the virtual mine case study. It is concluded that the Machine Repair Model can be an affordable model compared to off-the-shelf generic software because it is easily modelled in Microsoft Excel, a software platform that most mines already use. This paper reports part of the work of a MSc research study submitted to the University of Witwatersrand, Johannesburg, South Africa. Keywords: simulation, bunching, probability distributions, cycle time, queuing, matching, shovel-truck, OEM.

Jan 1, 2007

By G. G. Gold

A leach pad’s fluid flow characteristics greatly affect the recovery of metals from heap leaching. However, because there are other factors such as particle size distribution, application rate and method, and chemical reactions to consider, mining companies often overlook potential problems associated with fluid flow until it is too late. In an effort to better understand the dynamics of fluid flow in leach pads, a series of experiments were preformed using temperature probes. A model leach pad was set up using a particle size distribution, fluid application rate, and application method common to modern leaching methods. Variable water temperatures were applied in succession and data gathered from the three dimensional grid of temperature probes built in to the model. Current work is analyzing these data along with visual observations of the model, computer simulations, past mining experiences, and other related research, in an attempt to develop a low cost test that could be performed prior to large scale leaching to determine the fluid flow characteristics of a particular ore. This paper will summarize the work and findings to this point as well as suggest areas of additional related research.

Jan 1, 2004

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002

By Hisashi Takahasi, Hironobu Yamazaki

INTRODUCTION The slurry shield method was developed in Japan in 1963 and its experimental tunnelling work was performed in 1965. Although the history of this method is short compared with the conventional shield method in Japan, many companies such as Tekken Construction, Okumura Gumi, Nishimatsu Kensetsu, etc. are engaged at present in developing their own unique system of the slurry shield method. The ground of Japan is generally pervaded with ground water and a large number of districts are covered with soft ground, which is composed of fine sand, silt and clay, etc. Therefore, the conventional shield method has always used compressed air with various kinds of auxiliary methods. However, with this method there have been experienced numerous troubles such as ground settlements, lowering of ground water, oxygen shortage within the tunnel, and so forth. The slurry shield method has been developed with the above background. In recent years remarkable progress has been made from the engineering viewpoint in applying this method to driving various kinds of tunnels such as road tunnels, subways, water supply and sewer tunnels, and other tunnels. Apart from Japan, the slurry shield process using bentonite is carried out in England and Germany. OUTLINE OF SLURRY SHIELD METHOD (1) System of Slurry Shield Method Since the conventional shield method drives tunnels using com-

Jan 1, 1976

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By R. W. Raymond

EDWARD COOPER, was born in New York City, October 26, 1824. His father, Peter Cooper, to say nothing of manifold reasons for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment of public schools; and it is not surprising that he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia. College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.* For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the strident of those data which the modesty of the man permitted to be placed upon public record. Edward Cooper's mind was one of the most active, accurate and subtle with which I have ever come into contact: He had inherited from his father a sunny, benevolent temperament, and' the irresistible impulse to attack all new problems which challenged his attention. His thorough education had 'indeed made him wiser than his father, both in philanthropy and in technical inventions. He could condemn and reject a proposition which Peter Cooper would have embraced, in a splendid, though ignorant, faith that nothing was impossible to an. American, and that the word ? impossible " was simply a label,

Jul 1, 1906

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

By J King, T Hunter, R Coleman

"The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.Trends amongst service providers will be put forward as well as developing options and alternatives. These embrace a whole gamut of agile alternatives in the areas of partnering, alliances, commercial and shared risk models and mutual innovations. These will be discussed with some case studies and suggested approaches.Particular emphasis will be upon brownfield expansions and upgrades which have emerged recently as a preferred lower capital and focused way to achieve best practical outcome at lowest cost. There are a number of specific features of such brownfields projects including the requirement for very close cooperation between the execution team, operators, maintenance and suppliers and a maximum usage of site resources and ingenuity. Often, required investment hurdle rates are high, downtime allowed is minimal and site resources usage is maximised. This requires mutual trust, good planning and high health, safety, environment and community (HSEC) standards and practice. In many ways the practices and skills needed are the exact opposite of the historical ‘big greenfields’ project with which the industry has been geared for more recently.Another developing area has been with innovative commercial models and practices. These have been as a direct result of the more challenging investment criteria being adopted and the relative hunger of service providers. It has become more common to look at these commercial/costing alternatives very early in the project cycle as an essential project tool and not just as a possible option. These commercial solutions cover such alternatives as leasing and rental, deferred payments, build–own–operate–transfer (BOOT) and build–own–operate (BOO), whole-of-mine preferred spares and maintenance terms, and aggressive performance targets with real assurance penalties. Once again this requires very close mutual dealings and trust, and sufficient time allocation compared to a conventional approach.Citation:Coleman, R, King, J and Hunter, T, 2016. Upgrades, Modernisations and Expansions... Where Will the Expertise, Capability and Skills Come from in the Future?, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999