Search Documents

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By J. Pizarro

Any organization that subjects its activities to a continuous improvement methodology, aiming to optimize their processes and services, must be able to adequately measure the results of the implemented changes to pursue better outcomes. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators. Over time, many tools were developed for us to obtain PSD data, albeit each of them had their own shortcomings. The first ones to be developed involved photographing the muck pile including a scale object, uploading those photos to a PC, and using specialized software to analyze each one. As a result, analysts would get a PSD curve that served as reference for the performance of the blast. This method, which is still used, has major shortcomings. The most obvious one is that it is only able to capture a slice of the blast, which corresponds to the exposed section of the muck pile the analyst has access to, and even there its reach is limited to the areas that are safe for getting close enough for placing the scale, which are not many. Consequently, this is a very limited way to get a fragmentation performance assess for a blast. Currently, autonomous systems are capable of taking continuous pictures of the muck pile. Installed on a shovel, conveyor belt or crusher feed, these systems can take a continuous stream of pictures that are later analyzed automatically without the need of human intervention. These systems greatly increase the volume of data and, consequently, we have a PSD curve that is more representative of the blast performance. However, this technology still had issues when trying to sample front end loaders mining operations or getting results from underground blasting due to the inherent difficulties of these operations. New algorithms used for capturing and processing data for front end loaders can overcome the harsh environment of their operations and produce PSD data in high vibration environments and difficult mining angles. For underground mining, algorithms can be used to sample each truck exiting the mine, giving a reliable source of fragmentation analysis that can be traced back to their stope of origin. The development of this technology extends the existing system’s capabilities and helps us in our efforts to improve fragmentation results with each blast.

Jan 1, 2024

By Phillip Martin Warren

Safety and productivity are critical factors in the performance of the Australian Mining Industry. In this sense, the paper point out that while the multiple dimensions of both training and productivity make it difficult to quantify the relationship, it is clear from this study that organizations that conduct training consider that there is a very positive link. Training is seen as a very important activity by the vast majority of organizations surveyed, and is an activity from which they consider they are gaining significant, and often very substantial productivity benefits. Therefore, it predicts well for productivity of Australian enterprises which invest in training.

Sep 13, 2001

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By Wieslaw Blaschke

The transformation of Polish economy, has contributed to the significant ownership changes and the way of management. Most of non-ferrous metals producers are now joint stock companies or stock companies, which shares are owned mostly by Polish shareholders, the State Treasury, banks or trading companies. However, as compared to the international tendencies, the cost of production of base metals in Poland are still relatively high, and the utilization of secondary sources is still very low. In this sense, the paper point out that some positive results of the current pro-ecological mineral policy in Poland have been already clearly visible in the case of non-ferrous metals smelters, where the emission of dusts and gases was significantly reduced. Therefore, if the current increasing tendency of world production of non-ferrous metals continues, Poland’s role as their primary producer will be reduced.

Sep 13, 2001

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

Investigation on Comprehensive Utilisation of Nickel Slag from JNMC

Sep 13, 2010

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 'by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By George J. Young

DR . JOHN A . CHURCH, in his treatise on the Comstock Locle 1 gave a full and clear account of the conditions of the mine during the period of greatest activity. The difficulties in the way of deep mining at that time were excessive water and high temperature. The drainage of the mines taxed the financial resources of the mining companies, and the high temperatures restricted the capacity of the miners for underground labor. In spite of these difficulties exploratory work was continued until the financial burden of removing the water became too great. The companies then restricted the work to the upper levels. The years 1883 to 1886 marked the period of cessation of deep mining. For 12 years thereafter mining was confined to the levels above the Sutro tunnel; and, while the question of drainage was more or less agitated, nothing of importance was done until the formation of the Comstock Pumping Association in 1898. Since that time successive levels have been drained until, at present, on the north-end mines, a depth of 700 ft. below the Sutro-tunnel level has been reached. Mining is now carried on in the Ophir mine from the 1,700- to the 2,200-ft. levels, and a winze is being sunk to make connection with the 2,300-ft. level (the 2,450 ft. of the C. & C. shaft). In 1903-the Ward Shaft Association was formed to undertake the draining of the Central and Gold Hill group of mines, and at the present time a depth of 2,500 ft. has been reached in the Ward shaft. The situation at the Ward looks promis¬ing, and the 3,000-ft. level may be reached in the near future. It is proposed to establish a large pumping-station on this level, and then begin the opening of known ore-bodies and the prospecting for new ones. The main factors which have contributed to the successful solution of the drainage problem are the Sutro tunnel, the use of the hydraulic elevator as a sinking-pump, the concentration of pumping-units, and cheap electrical power. The question of high temperature and its control still remains as a minor but important problem. The temperatures encountered in the new workings are as great as those in the earlier periods. The Comstock was considered the hottest group of mines in the world, and I am not aware of similar conditions in any other mining-district. A water-temperature as high as 160° F. has been reported from the Ward shaft, and temperatures below the Sutro tunnel are very high in many instances.

Nov 1, 1909

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By John Plecash

This paper comprises a general outline of all of the developments, including the history, geology, mining, milling, power and transportation installations, at the gold mining operation of La Luz Mines Limited and the copper mining operation of its wholly-owned subsidiary, Rosita Mines Limited, both located in north-central Nicaragua. The low-grade, gold-bearing ore-bodies of La Luz Mines, contained in highly fractured and folded Lower Cretaceous sedimentary rocks, were from 1909 to 1928, mined and treated by primitive methods by the La Luz and Los Angeles Mining Company. The abandoned property was acquired by La Luz Mines Limited in 1936, and was equipped with modern machinery and put into production in 1939. Between 1939 and 1948, the daily rate of production was in-creased from 300 tons per day to 2,-000 ton per day. The ore reserves available for open-pit mining were depleted in 1954. Since then, the entire production has come from under-ground operations.

Jan 1, 1963

By Michael Rieber

This study is an extension of our previous work in the area of coal transportation Its subject is the comparative costing of competing transport erodes. A wide range of costs and aspects of costs are dealt with in terms of engineering - economic analyses of the cost of the components which make up the facility and operating system descriptions of each coal transport mode. The cost comparisons, though analyzed, are not meant to be statements of policy but, rather, an input to decision making. The technical material presented in the succeeding volumes, alone with the earlier work cited above, forms the basis for the analyses. This material may also broaden the general understanding of coal transportation issues and problems. The project is divided into two main sections: (1) lone distance coal transport and (2) gathering and distribution systems. Within each section economic and technological comparisons are made of the available modes. These are used as the basis for comparisons among the modes. Inter-modal compatibility is studied with respect to both mixed trunk line shipment anti with respect to feeder to trunk line and trunk line to distribution systems. The engineering and technological data form the bases for the costing and economic analyses.

Jan 1, 1977

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By K. T. Lee, M. U. Ozbay, M. D. G. Salamon

Design of yielding chain pillars in deep coal longwall mines is not as well established due mainly to the lack of knowledge in the behavior of coal pillars in the post-peak regime. This study shows that two of the existing strain-softening models have the potential to provide an improved understanding of yielding and, therefore, could form a rational basis for yielding coal pillar design. Analytic and numerical modelings of a row of chain pillars in a two-entry development at a depth of nearly 700 m suggests that yielding pillars are feasible, but the design is very sensitive to the coal’s post-peak behavior.

Jan 1, 2001