Search Documents

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By W. F. Hazen

This paper describing the mining practices at a 100 per cent mechanized mine working the Pittsburgh or No. 8 coal bed in eastern Ohio is one of a series being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The purpose of assembling this data is to place before those interested in the mining industry the methods employed and the cost data on the items involved in the winning of the coal and its removal to the railroad car at the tipple. Mining costs are governed by the mining method used, which is selected for its adaptability to local natural physical conditions such as the nature and thickness of the coal, its dip, the character of the roof and floor, and the thickness of the overlying strata.

Jan 1, 1929

By P. Valicek

Anglo American Platinum Limited is constantly striving to improve safety and productivity. There are many different initiatives taking place within the organization in order to ensure continued safe operation and profitable ounces for the future. One of the opportunities and potential growth areas that has been identified and is being explored is that of mechanization. In order to do this, the approach that has been adopted by Anglo American Platinum is to fully understand and analyse the current mechanized mining methods. Once each configuration is fully understood, the method can then be optimized and new mining technologies and systems can be developed to overcome the current shortfalls. This paper will discuss a methodology that was developed by Anglo American Platinum (in conjunction with Cyest Corporation) and adopted to optimize the mechanized mining layout and fleet configuration, and will also present the final findings of the study. Due to the impracticability of piloting every possible option in the workplace, extensive modelling and simulation exercises were conducted to determine realistic parameters for productivity and value. The study resulted in a full understanding of mechanized mining systems and their associated layout. From the results of the study a mining / logistic layout was developed which highlighted the following opportunities: 1. Create safe operations through the reduction of personnel in the ?high-risk zone? of stopes 2. Separate machines and personnel by use of remotely operated machines 3. Create focused mining on primary development from the production stoping, thus having dedicated teams on development and stoping. 4. Develop primary development ahead of the stoping activity. This enables: a) Understanding of the geology and subsequent implementation of the correct b) technology (?fit-for-purpose?) required to mine that area based upon this geological knowledge c) Ability to install tipping points ahead of stoping, creating ?immediate stoping reserves?, thus increasing flexibility and reducing production risk d) Improved productivity by having adequate faces available and reduction in re-development to establish faces. 5. Quicker return on Investment due to recovering revenue from ?on-reef development? 6. The layout allows flexibility between stope sections enabling better ?resource sharing? 7. Optimize the long-term ratio of machine makeup of the fleet in relation to the production outputs 8. Creates an agile mining layout allowing rapid response to market pressures. The findings and work presented in this paper is currently being implemented at different test sites within Anglo American Platinum and will demonstrate that improved safety and productivity can be achieved through the adoption of mechanization.

Jan 1, 2012

By Patrick D. Plumb

The Bureau of Mines (BOM) has begun a project to increase the understanding of the relationships between ecosystem health and its functions, and minerals development. The BOM, Juneau Branch, Alaska Field Operations Center, is providing support for ecosystem based land-management decision-making and the development of ecosystem based regulations by documenting the effects of mining on ecosystems and demonstrating the tools used to assess and analyze those effects. This is done by reviewing the data available on ecosystems and the environment at a mining site, the Greens Creek Mine near Juneau, Alaska, and applying available Geographic Information System modeling tools to assess the impacts of the mine on components of the pristine ecosystem. Habitat Capability Models for wildlife indicator species are used in this examination. Wildlife indicator species are used as indicators of ecosystem health by the U.S. Forest Service and the Alaska Department of Fish and Game, who developed these models for southeast Alaska. Analysis techniques from the U.S. Fish and Wildlife Service's Habitat Evaluation Procedures (HEP) are also used in this report. By applying available models and analytical techniques to the Greens Creek area, the benefits gained through mitigation of potential impacts become apparent. These or similar techniques are useful for cost/benefit analysis of mitigation alternatives. Also apparent from this analysis is that the degree to which potential impacts are observable will depend upon the ecosystem scale considered. This demonstrates the importance of defining the ecosystem and scale before performing impact and cost/benefit analysis. The watershed scale is found to be useful for assessing impacts to ecosystem components at the Greens Creek Mine. Much progress remains to be made in the modeling and prediction of impacts to ecosystems from mining activity.

Jan 1, 1994

By David Sherwood

The paper has been prepared as the basis for the 2008 John Mitchell Memorial Lecture. It reviews major developments in ground engineering over the last 20 years, not from the point of view of technical processes, but from the drivers that have driven these developments and the needs that they have met. It concludes with a glimpse into the future and suggests to where current trends will probably lead us. By its nature such a review is closely aligned with personal experience and it relies heavily on case histories largely from within the writer?s own experience over that period.

Jan 1, 2008

By T. S. Washburn

THE grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure-killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes are not present. Also, the rimmed ingot has no well defined pipe, as com-pared to the deep pipe on the killed ingots, and there are numerous pri-mary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differ-entiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7-as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined or deep as in the killed ingot of Fig. 1. In killed ingots, pri-mary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

After some 50 years of worldwide research in relation to coal pillar mechanics and design as well as numerous workshops and technical papers related to these issues there is still some significant disagreement as to the approach one should adopt in the assessment and design of a coal pillar. Of course there are many different types of coal pillars that fulfil a wide range of roles at any particular mine and in this instance it is appropriate to have a 'tailored' approach for each pillar type in relation to the role it fulfils. However where it can become very difficult for the mine operators is when various researchers or consultants use or recommend significantly different approaches for the same type of pillar fulfilling the same role. By 1999 two pillar design techniques had been developed specifically for the Australian underground coal mining industry (ie The University of New South Wales Pillar Design Procedure, UNSW PDP and Analysis of Longwall Tailgate Serviceability, ALTS) and several other pillar design techniques were being practiced by individual consultants. The Australian industry hoped to resolve the issue of what technique to use for each pillar type and role, when it funded UNSW in 2000 to develop a 'Systems Approach to Pillar Design'. The findings of the abovementioned project were published in 2005 and while every attempt was made by UNSW to include the views of various local and overseas researchers and consultants it would be fair to say that a unified approach to pillar design in Australia was not adopted as a result of that project. This is the experience of one country where there has never been one central group solely undertaking such research in relation to pillar design (such as the Chamber of Mines in South Africa). This paper explores the Australian experience in terms of pillar research and what that experience may offer to researchers in Australia and other countries. At the First Australasian Ground Control in Mining Conference (2003) the first 'update' of the ALTS Design Methodology (ie ALTS II) was presented. In subsequent years the ALTS database was continually updated and significantly expanded such that it now includes detailed information in relation to both the tailgate (148 cases) and maingate belt road (58 cases). In addition to tailgate roof support and chain pillar design, the current version of ALTS (referred to as ALTS 2009) includes a maingate belt road roof support design module. This paper is also intended to update and summarise the development and application of the ALTS Design Methodology for longwall gateroad design over the last decade both directly and in the context of coal pillar research conducted in Australia over the last 15 years.

Nov 25, 2010

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By John R. Freeman

This paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful developnlent of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitablc die-casting machines. The melting point of copper is 1084" C. (1983" F.) and of a high brass about 900" C. (1652" F.), as compared to 327.5" C. (621.5" F.) for lead, 419.4' C. (786.7" F.) for zinc and 658.7" C. (1217.7" F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals. Type of Die-casting Machine In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy. For alloys having the relatively high melting point of brass, this obviously is impossible. Machines with a separate melting chamber are essential. Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co., the latter developed by Joseph Polak, of Prague, Czeclioslovakia. The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg.4

Jan 1, 1935

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By H. O. Ghaffari

A complex network approach on a rough fracture is developed. In this manner, some hidden metric spaces (similarity measurements) between apertures profiles are set up and a general evolutionary network in two directions (in parallel and perpendicular to the shear direction) is constructed. Also, an algorithm (COmplex Networks on Apertures: CONA) is proposed in which evolving of a network is accomplished using preferential detachments and attachments of edges (based on a competition and game manner) while the number of nodes is fixed. Also, evolving of clustering coefficients and number of edges display similar patterns as well as are appeared in shear stress, hydraulic conductivity and dilation changes, which can be engaged to estimate shear strength distribution of asperities.

May 1, 2009

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By Rick Coleman

PT Freeport Indonesia’s (PTFI) latest expansion has increased total mill throughput to 125kt/d (137,700 stpd). The most recent expansion included the installation of a semiautogenous mill (SAG) designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation, including conventional and column cells, and a regrind circuit. All equipment is supported by a modern distributed control system. PTFI’s operations are located in the Ertsberg mining district of Irian Jaya’s Jayawijaya Mountains, the eastern-most province of the republic of Indonesia on the Island of New Guinea. PTFI, the operator, is owned by Freeport McMoRan Copper and Gold (81.3%), the government of Indonesia (9.4%) and private Indonesian investors (9.3%).

Jan 1, 1996

By Augustus Locke

I WISH to urge on this Committee the task of evaluating mining geology. -My motive is as follows: It, is a. duty of the Institute from time to5 time, to establish the social perspective of the professions grouped within it, not simply to promote their use, but to determine with engineering definiteness their true powers and functions. This becomes the delegated duty, therefore, of this committee in respect to geology. Be- cause my own subject is mining, I shall confine my remarks to mining geology. But I believe that the evaluation should be made to include all of that geology termed economic. The perspective for such evaluation is shown in the nature of the public support given to geology. The federal Geological Survey, the leading organization on the economic side, is actuated by the zeal of a small group of devoted professionals who consider its work valuable, ' It proceeds, however, on a starvation ration of appropriations, and that implies that neither the corporations, the voters nor the vote getters consider it important. Altogether, in' the public consciousness, geology is negligible. That, at the same moment, .the profession should act with full confidence, while everyone else should act' with opposite motives, is not fitting. For us, as a committee, to remain incurious regarding such a disparity of beliefs is quite impossible.

Jan 1, 1931

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942