Search Documents

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

By P wade

This is the first Presidential Address given to the Nottinghamshire Branch of The Institution following the merger of the Nottinghamshire and North Derbyshire Branch of The Institution of Mining Engineers (IMinE) and the Midland Branch of The Institution of Mining Electrical and Mining Mechanical Engineers (IMEMME). I intend to review the formation of the individual institutions as well as what has been achieved by mining related institutions over the years and finally I intend to look to our future.

Jan 11, 1996

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Thomas J. Peters

The Goat Rocks RARE II further planning areas contain no known mineral resources and have very low mineral potentials. County mining records show only one mining claim area; however, no mineralized material was found at the described location. Andesite suitable for building stone may be present, but similar material can be quarried more economically elsewhere. Several anthracite coal prospects are near the area, but the likelihood of finding an economic deposit of coal or other fuel is very low.

Jan 1, 1981

By R. Melley, P. Wissner

The paper looks at the basic theory of tri-bological wear and the role played by the lubricant and its additives. It presents the argument that the “real cost of lubrication” is not the purchase price of the oil or grease, but rather the costs associated with not using the correct lubricant. A number of examples are presented, covering oils, greases and additives, in which a detailed evaluation of the application has shown that when all of the benefits of using the best lubricant/additive are evaluated, the savings achievable greatly surpass the incremental cost of the superior lubricant. One of the emerging classifications of costs in industry today are those associated with environmental protection. Two of the examples used describe the replacement of more conventional lubricants with environmentally acceptable products, compounded to compete in all aspects of serviceability, but which have the added bonus of being not only biodegradable but also of being of low toxicity.

Jan 1, 1997

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By Robert W. Van Dolah

The prevention of fires and explosions involving the combustibles and oxidants likely to be found in flight vehicles requires a knowledge of the flammability and related characteristics of these materials. This circular is a compilation of the available charactersilics data for a series of combustibles and oxidants of current interest. Vapor pressure data are presented for fluorine, oxygen, chlorine trifluoride, nitrogen tetroxide, nitric acid, hydrogen peroxide, ethylene oxide, hydrogen, ammonia, pentaborane, unsymmetrical dimethylhydrazine, monomethylhydrazine, hydrazine, and a series of hydro-carbons including decalin, tetralin, bicyclohexyl and other high-density fuels. In addition, flammability characteristics diagrams are included for each of the fuels in contact with air and, where available, other oxidants (for example, oxygen and nitrogen tetroxide). To assist in understanding these data, sections on definitions and theory and applications have been included. Each section is complete in itself and can be used separately. For example, a reader who is familiar with the general theory of combustion and detonation may find the data sections more useful than the definitions and theory and the application sections. However, since pertinent data are included in these sections, they should also prove useful to the experienced engineer interested in preventing fires and explosions.

Jan 1, 1963

The Bibliographic Data Base is the result of a literature search con-ducted as one task of the technology assessment of current and advanced logging techniques, sponsored by the United States Bureau of Mines. After compilation, the bibliography was converted to an automated form for ease of utilization, and to allow for maintaining and updating the data base. The data base covers articles, symposia, books, patents, corporate and government reports, and other literature concerned with some aspect of borehole logging from January 1969 through December 1975. Periodic up-dating will be necessary to keep the data base contents in step with developments in the rapidly advancing field of application of borehole logging to mining. Many bibliographic indexes were scanned for entries relating to the subject of interest, and those entries which were included in our data base contain a reference to the bibliographic index in which they were listed (see Section 2.4.7). With the aid of these indexes, a vast number of publications, including foreign reports and publications, have been scanned for works relevant to borehole logging technology.

Jan 1, 1976

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Joseph M. Kuchta

This Bureau of Mines manual is oriented to the technical needs of an investigation of fire or explosion accidents and includes various practical and theoretical information that is needed in analyzing accidents or evaluating conditions that might lead to an accident. It is applicable to accidents in the chemical, mining, transportation, and other fuel-related industries. Specific procedures for conducting an accident investigation are outlined, and various guidelines are given for developing the fire or explosion evidence. Ignitability, flammability, and physicochemical data are presented for over 500 combustible gases, liquids, and solids; empirical and theoretical expressions are also given for extrapolating the behavior of combustible-oxidant-diluent systems to various environmental conditions. In addition, various data pertinent to damage analysis are summarized to facilitate the task of the investigator in developing plausible accident scenarios.

Jan 1, 1985