Search Documents

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By Leonard N. Hill

Cyprus Sierrita Corp. has 16 parallel 5.03 m-diam x 5.8 m long (16.5 ft-diam x 19 ft) primary ball mills, each operating in closed circuit with a nest of cyclones. Before the upgrade to 840 mm (33 in.) cyclones, each mill operated with a nest of five 660 mm (26 in.) cyclones - four in use and one on standby. In this configuration, the mill throughput was 88.5 kt/d (97,500 stpd). Flotation feed averaged 25.9% +212 pm (+65 mesh). The 660 mm (26 in.) cyclones normally operated at an inlet pressure of 34 kPa (5 psi), lower than the inlet pressure of 55 kPa (8 psi) recommended by the manufacturer. The circuit was typically operated with cyclone overflow densities greater than 40% solids to achieve the required throughput. This resulted in inefficient cyclone operation and excessive coarse oversize reporting to flotation. The apexes choked frequently. Larger apexes were tested but reduced the classification efficiency and resulted in circulating loads greater than 800%.

Jan 1, 1994

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989. Previous drilling indicated over 100 million cubic metres of gravels with some 90 per cent of the gold in the bottom seven metres. The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below. Metallurgical studies and exploration were initiated when the project commenced. Leasing and environmental considerations were investigated and action taken. While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By E. G. Kearnery

Introduction It is believed that the present paper will be of some interest, not because of any outstanding features of Renabie milling practice but because Renabie is the first gold mining property in a newly explored area - in Leeson and Rennie townships, Sudbury district, Ontario - to reach the production stage. The Renabie mill was originally designed by the General Engineering Company (Canada), Limited, as a 300-ton plant and went into operation in June, 1947, treating an average of only 128 tons a day for the balance of that year. Toward the end of 1948 the capacity of the plant was expanded to 450 tons a day, and the tonnage treated was gradually increased from the 1947 figure to the point where 420 tons a day was averaged for the first nine months of 1949. Description of Ore In general, the outstanding gangue component of Renabie ore is white quartz, which comprises at least 80 per cent of its total bulk and in some sections considerably more. Virtually all the gold occurs in very finely divided state; only very rarely has free gold coarser than 325 mesh been observed. The ore has a very low sulphide content, ranging from about 0.50 to 1.00 per cent by weight. The gold occurs both free in the gangue and ? locked in sulphides, the proportion of one to the other varying considerably from one orebody to the other. Pyrite is by far the most abundant sulphide, followed by galena, which, however, appears to be entirely absent in some of the orebodies. Minor amounts of pyrrhotite, chalcopyrite, chalcocite, and sphalerite have been noted. The ore appears to be entirely free, or almost so, of minerals containing arsenic, antimony, or molybdenum, and in general it could be described as free milling. The various hindrances to extraction of the gold which have been met with are believed to be due largely to the very finely divided state of the metal and to its intimate association with the sulphides and gangue. The ore contains silver, with the gold-silver ratio about 3:1.

Jan 1, 1950

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more 'models' available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of 'international standards' we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry's best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By J. M. Font, R. G. Reddy

Jan 1, 2004

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By S. R. Zimmerley, C. H. Schack

"INTRODUCTION The pilot-mill concentrator at Boulder City, which has a nominal capacity of 40 tons per day, was planned and built to investigate further the beneficiation of domestic manganese ores that have been concentrated successfully in the ore-dressing laboratory. As milling of manganese ores in general is a new field, it is necessary to prove the success of laboratory processes by means of large-scale operations employing standard milling equipment, and thus to obtain engineering and metallurgical data essential to designing and operation of full-scale concentrating mills.The first ore tested in the pilot plant was the Three Kids Annex manganese ore from the Las Vegas Wash area 15 miles southeast of Las Vegas, Nev. The deposit was worked for its high-grade ores during the First World War From 1930 to 1939, 4,500 feet of diamond drilling was completed by a private company. Diamond drilling started by the Bureau of Mines in November 1940 and completed in July 1941 aggregated 6,600 feet. Exploration by the private company and the Bureau outlined reserves of about 1,000,000 tons of ore assaying plus 28 percent manganese. A much larger tonnage of lower-grade ore also was outlined by the drilling.Because of its physical nature, the Three Kids Annex ore had long proved unamenable to concentration by ore-dressing methods. The ore is a mixture of manganese oxides (wad) filling the pores and to some extent replacing a silt composed of very fine grains of volcanic tuff, quartz, feldspars, other silicates, and clay. Some gypsum occurs as fillings along fracture planes. The ore is light and very porous. Upon wetting, it disintegrates into granular but friable particles and a large amount of slime. It is these characteristics that make the ore so difficult to concentrate."

Sep 1, 1947

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By R. Adsero

The analysis of equipment trends in AUSIMM?s Revision of Monograph 19; Australasian Mining and Metallurgy Operating Practices (AMMOP) in the paper by Dight et al (in press) raised some interesting and in parts disturbing trends in the Open Cut Mining Industry. According to the US Bureau of Labour Statistics the US mining and petroleum industries? productivity is down by 12% since 2004 while the Australian Bureau of Statistics shows the productivity of the Australian mining industry is down by 34% since 2001. In terms of open cut equipment median output for draglines is down by 15% since 2003; electric rope shovels are down by 41% since 2003; hydraulic excavators are down by 39% since 2008; front end loaders are down by 39% since 2007 and trucks are down by 41% since 2006. Clearly the boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top 10% by annual output per unit of input) has declined but not by as much as the median (eg. shovels down by 8%, excavators down by 19% and FEL?s down by 5%). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one will be crucial to reversing the decline in open cut equipment performance.

Feb 27, 2013

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By N. M. Langdon

INTRODUCTION. IN considering the magnificent success of Mr. Gayley's Bold experiment of applying dry blast to the blast-furnace, whereby , saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether, still further economy in fuel is possible, and, if so, how it is to be attained? The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation,. tinder various conditions, of a number of furnaces, for which such information has been worked out., should enable us to form some conclusion on the subject. The tables and calculations given below cover the operations of several furnaces reported in our Transactions; also the two furnaces using natural and dry blast in ,Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces.. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated. for A and B in Table III. are those given by Professor Richards; except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table III. for comparison with C and D.)

Oct 1, 1909