Search Documents

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By Francisco Zenteno

Dado que la operación aurífera de Pierina representa uno de los costos operativos más competitivos del mundo, la minera Barrick Misquichilca trata de proporcionar un grato ambiente de trabajo para su personal, estimulando la creatividad y la polifuncionalidad en sus empleados. Por ello, nace el proyecto SIP2000 donde optimiza el sistema de información para el mantenimiento preventivo de la planta de procesos en la mina Pierina. El proyecto comprende el desarrollo de tres fases: La primera fase comprende la definición de los principales equipos críticos que podrían afectar a la producción, asímismo la implementación y estandarización de redes de comunicación entre equipos críticos para finalmente desarrollar interfaces HMI que supervisen variables relativas a Mantenimiento. La segunda fase, integra todos los sistemas de supervisión y control de planta con los sistemas de seguimiento “online” de Mantenimiento (fase 1), desarrollando un solo sistema de tratamiento y análisis de información de planta; y la tercera fase comprende la instalación y el desarrollo de aplicaciones basadas en tecnologías Cliente/Servidor con base SQL, que finalmente proporcionan la información y los medios para realizar consultas que optimizan el seguimiento y toma de decisiones relacionado al mantenimiento preventivo/predictivo.

Jul 17, 2000

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

By A C. Edwards

The Mongol-Okhotsk belt consists of detached fragments of the Circum Pacific fold belt which have been trapped within the Mongol-Okhotsk fold belt. In its western part, the structures of the belt form an east-facing loop that is not connected with the other orogenic structures of Central Asia. In the eastern part of the belt (the Mongol-Okhotsk suture zone) the terranes form a zone between the Siberian craton to the north and the Bureya composite terrane to the south, that is linked with the Circum Pacific belt. The accretionary terranes, together with their Precambrian backstops, form a series of consistently-stacked, paired units that are bounded by northwest and north trending sinistral strike-slip faults. The ages of the rocks forming these accretionary complexes vary from Late Precambrian - Carboniferous in the west to Cambrian - Jurassic in the east. The terranes developed due to a progressive westward stacking of the accretionary complexes during the process of accretionary growth. The magmatic rocks young eastward indicating that migration of the magmatic front of the arc followed the eastward growth of the accretionary complexes. The accretionary terranes may be differentiated by their Paleozoic lithological assemblages. Only the Selemdzha, Niman, and Kerbi terranes located in the eastern part of the Mongol-Okhotsk suture zone contain significant amounts of black shale, and it is these terranes that host the bulk of the hardrock and placer gold mineralisation that is present within the suture zone. Gold mineralisation is present both as vein style and disseminated mineralisation within structural duplexes.

Jan 1, 1999

Fire-clay blocks lining the combustion chambers of zinc concentrate flash-roasting, furnaces operating at 1,000-1,200° C. have suffered moderately rapid deterioration due to slagging. The attack is accentuated by high temperatures, and is probably caused by lead oxide volatilized from the roasted concentrate.Resistance of refractories to attack increased with increasing alumina content from 30 to 45 per. cent but at 90 per cent alumina spalling was troublesome. Magnesite bricks were'subject to some spalling, but some types may lie satisfactory. Chrome and chrome-magnesite bricks spalled seriously.Material thought to be suitable for use as a monolithic lining slagged badly and an alternative may be tested.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Ltd. uses two multi-hearth furnaces and four flash or suspension roasting furnaces for the roasting .of zinc concentrates at its Risdon Works. The hearth roasting plant has been described previously by Forster (1949).A brief descriptioI1 of the first three flash roasters was given by Gordon and Forster (1955). A fourth flash roasting furnace began operation early in 1957. This furnace is somewhat larger than the earlier furnaces, and the designed capacity is also higher, auxiliary equipment being altered to suit. An important structural difference between the older furnaces and the fourth flash roaster is that the walls of the combustion chamber of the new furnace are lined with high alumina fire-bricks instead of fire-clay blocks. Thischange was made because the fire-clay blocks in the older flash roasters had shown s-evere wastage due to slagging by lead derived from the concentrate.

Jan 1, 1959

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July 1, 1936. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders to whom specific credit is indicated.

Jan 1, 1940

By N. Duda, W. Koperska, S. Anufriiev, P. Stefaniak

In mineral processing plants ore extracted from mines is processed to obtain a concentrate with the highest possible concentration of this valuable product. It is a complicated multi-stage process. Usually, the first step is sieving the ore, which is typically done using vibrating mining screens. There is often only a limited number of these machines in the technological chain, which is why their continuous operation, and proper maintenance is crucial for the whole process. Predictive maintenance is the best strategy in this case because it allows for minimising the number and duration of unexpected stoppages. It consists of the prediction of future failures based on available real-time data, and predictive models built upon this data using, for example, machine learning techniques. In this paper we concentrate on feature generation for future predictive maintenance model development for a vibrating screen, based on an example of a KGHM ore processing facility in Polkowice-Sieroszowice. We focus on two types of measurements: bearings temperature and vibrational data. Based on the raw data, the process of more advanced feature engineering is described. By transforming the temperature data we calculate characteristics of bearing cooling and heating dynamics, while based on vibrational data, the aggregated characteristics of the vibrations are derived. Such features are calculated on a long-term basis, and then they are compared to the data related to vibrating screen maintenance to estimate their significance for the prediction of particular failures of the machine.

Sep 1, 2021

By R. W. Hodder

"Archean lode gold deposits of both vein and chemical sedimentary types typically have major enrichments of certain rare elements, including Au, Ag, As, Sb, B, W, Se, Te and Bi, coupled with low or negative enrichments of the more abundant and mobile base metals, Cu, Pb and Zn. On the other hand, in massive base metal sulphide deposits Au, Ag, Cu, Zn and in some instances Pb are all enriched by a factor of 200 to 2000 t:'Jf'1pared to background and there is no large separation of gold relative to the base metals.The fluids from which gold was precipitated in veins were at temperatures of 320 to 480°C, at lithostatic pressure, had significant C02, and Na """" K; whereas the fluids which generated base metal deposits were at 250-300°C, at hydrostatic pressure, had C02 < < H20 and Na > > K.Many lode gold deposits are characterized by K, C02 and Si additions to their enveloping rocks, whereas base metal deposits typically have a fixation of Fe, Mg, Si and S in footwall rocks. Lode gold deposits may also have a relatively large halo of low-temperature oxidative, sadie spilitization in enclosing volcanic rocks, where seawater has later streamed into cooling stocks or flows that have initially acted to focus gold mineralizing fluids along thermal contraction fractures. The submarine environment is one hydrologically appropriate for the mixing of two initially independent hydrothermal systems, and the blending of their separate characteristics. Hence, lode gold and base metal massive sulphide deposits appear to be products of two distinctly different crustal and hydrological regimes. The former involves a high-temperature, high-pressure discharge of fluids which probably were generated during dehydration accompanying burial and progressive accumulation of volcanic-sedimentary sequences, with an additional influence of marine water in the near-sea-floor environment. The latter represents thermally driven convection of ocean water at lower temperatures and under hydrostatic conditions.Auriferous fluid systems with only minor base metal content could plausibly be generated during dehydration accompanying burial and metamorphism, when the water-to-rock ratio is low and halogen availability is limited by crustal abundance (- 60 ppm Cl). These two factors may constrain the uptake of the abundant base metals into fluids, but the solubility of rare elements is not constrained by limited fluid; and preferential uptake of Au along with other rare elements may be promoted if such elements compete more successfully for the limited halogens than the base metals, and/or have an alternative complexing agent such as CO or C()j-."

Jan 1, 1982

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.