Search Documents

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By Thomas L. Richardson, David R. Chapman, Gary W. Gilbert

The two contracts of the Big Walnut Augmentation/Rickenbacker Interceptor(BWARI) sewer project for the City of Columbus, Ohio total nearly 35,000 feet of 14and 12-foot diameter tunnel. EPB TBMs will install precast concrete segmental lining through difficult glacial soils ranging from clean granular to hard till with high groundwater and boulders, crossing roads, railroads, and a large stream. Construction of 12 shafts and a large Interconnect Structure involving major ground stabilization work is required. The paper will review design of major project elements and present an update on construction progress.

Jan 1, 2005

By J. D. Morgan

Demand for nonfuel minerals depends on the overall state of the economy, which steadily improved each quarter in 1984. New housing starts rose to 1.8 million units. Automakers turned out about 15% more cars (7.8 million) and 30% more trucks (3.1 million) than in 1983. Nevertheless, many domestic mineral operations experienced difficulties in 1984. This resulted from import competition greater use of newer engineered materials, emphasis on multi-unit housing and downsizing of motor vehicles. About 15% of our energy was imported. This in cluded $36 billion worth of crude oil and $22 billion in refined products This added significantly to the overall merchandise trade deficit of $12; billion. On the bright side for mining, coal production rose 14% to 810 Mt (890 mil lion st). Three-fourths o: the coal was burned to generate electricity and more than half of our electricity was derived from coal-burning plants. With the exception of a few large-bulk, low-value raw minerals, most minerals move relatively freely in world trade. The strong dollar encouraged imports and made exporting more difficult. Consequently, our nonfuel minerals trade deficit rose 60% to $19 billion, reflecting imports of $39 billion and exports of $20 billion. There were increased pressures from some major segments of the minerals industry for some form of import protection. But President Reagan said, "Our goal is a system of free and fair trade in goods, services, and capital. We will work toward this goal through both bilateral and multilateral trading agreements." The US minerals industry consists of domestic mines, concentrators, smelters, refineries, mineral manufacturing plants, and recyclers. It also includes many wholly- or partially-owned operations in many parts of the world, providing employment and income for US citizens and others as well. Compared with 1983, the value of US raw nonfuel mineral output rose 8%, to $23 billion. The $253 billion worth of goods processed from this crude mineral output was a 14% increase. Major Metals Raw steel production - a major indicator of both material use and mineral production-rose 10%, to 84 Mt (93 million st). This stimulated a 36% rise in domestic iron ore production, to 52 Mt (57 million st), about 98% pelletized. Iron ore imports rose 44%, to 14 Mt (15 million st). Despite the increase of steel production, output remained well below levels of just a few years ago. For example, 1984 production was still 23% less than in 1981. Raw steelmaking capacity remained steady at 122 Mt (135 million st). The industry continued to cite steel imports as a major reason for low domestic capacity. In December, pacts with seven leading steel exporting nations were announced. This is an effort to reduce import penetration to about 18.5% of the domestic market. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about 50% capacity. The US mined no manganese or chromium. Only a small quantity of ferronickel was produced from domestic laterite mining in Oregon. Molybdenum production, at 45 kt (49,500 st), rose threefold. Mine shipments of tungsten, another mineral tied to steel

Jan 5, 1985

By Arun Vathavooran, Adrian Singh, Michael Fletcher, Rainer Imhof

The Imhoflot G-Cell, a new development in the pneumatic flotation technology (which incorporates centrifugal forces in the separating vessel) is a recent innovation in the mineral processing world. The G-Cell was invented by Dr Rainer Imhof and commercialised by Maelgwyn Mineral Services Ltd. In a short time span a number of plants and units have been successfully commissioned in the mineral processing industry. In addition, a number of industrial G-Cell flotation plants are in the process of construction for the purpose of coal preparation and environmental remediation. In this paper two industrial installations have been highlighted together with a pilot plant test programme investigating ultra fine flotation recovery for a base metal operation.

Jan 1, 2007

By Shigeo Asai

"Electromagnetic processing of materials is newly proposed to be considered as one of the engineering fields where functions of electromagnetism are utilized for processing electrically conducting materials, such as liquid metals, electrolytes and plasmas. The background requiring this processing and the engineering characteristics supporting it are described. The applicable functions of electromagnetism to material processing are revealed from the view point of magnetohydrodynamics. The existing processes and the proposed ones are classified into utilized functions and engineering applications are discussed. IntroductionElectric energy has been used in the metallurgical field for the processes of melting, refining and solidification. In these cases both the magnetic field which is induced by an imposed electric current, and the electric current are applied on electrically conducting materials such as molten metals. Thus, it turns out that the magnetohydrodynamic (MHD) phenomena have unconsciously been seen in metallurgical processes using electric current. The academic backbone studying MHD phenomena is the Magnetohydrodynamics which is being developed in the fields of plasma physics, astrophysics, fusion research and nuclear energy.The first attempt where magnetohydrodynamics was intentionally applied on metallurgy was a Symposium of IUTAM (The International Union of Theoretical and Applied Mechanics) in titled as ""Metallurgical Applications of Magnetohydrodynamics"" at Cambridge, UK, 1982 [1]. This timely event stimulated a few metallurgists to recognize the importance of ~MHD and was a good warning to the metal societies in the world. Especially in Japan, the Steelmaking Investigative Subcommittee of Research Planning Committee in the ISIJ (The Iron and Steel Institute of Japan) discussed the application of ~IHD to metallurgy and selected it as one of the four major innovative subjects for future steelmaking technology in Japan [2]. Indeed, the term of ""Electromagnetic Metallurgy"" itself was firstly coined by this subcommittee. Upon the request of a report from the subcommittee, the ISIJ has established a committee on ""Electromagnetic Metallurgy"" at 1985, under the author's chairmanship."

Jan 1, 1988

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By Zhao-cheng Liu

Iron oxide red pigment powders of high quality were synthesized from pyrite cinders. Iron ox-ide red pigment powders were synthesized by hydrothermal method from the precursor of Fe(OH)3 and Fe(OH)2 colloid, which were obtained after ammonia solution reacted with acidic leaching solution produced by the reaction of pyrite cinders with sulfuric acid. Effects of reaction concentration, reaction temperature, reaction time, pH value and n(Fe2+)/n(Fe3+) on main properties of oxide iron red were studied by experiments. The prepared particles were characterized by means of X-ray diffraction (XRD) and scanning electron microscope(SEM). The results revealed that the synthesized iron oxide red particles were _-Fe2O3 and pseudocubic with particle size of 0.50~0.75µm. Furthermore, the quality of iron oxide red pigment powders reached the first grade of national standard (GB1863-89 ).

Jan 1, 2009

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

IN the irregularly shaped ore-bodies of the North Mount Lyell mine by overhead stoping, the method of filling the is a special feature.The situation of the mine two miles from the smelter and mill at an devation of 1000 ft. above the latter, precluded the economical use of granulated furnace or the mill tailings, even if these materials were as suitable for the purpose as the rock nowquarried at North Lyell methods at Mount Lyell have already been described in Proceedings of the Institute.*The breaking the ore in large dome-shaped stopes is still the rule, but the slope or "rill" is much flatter now than formerly. Owing the greater fluidity of the filling now in use, it is sometimes necessary to resort to square-sets, both at the ground floor and above, the roofs and walls are generally enough to permit stoping without timber, except for ground and occasional stacks on the rills.Sufficient area of ground floor has been beaten out to start overhead stoping, the dome back is partly formed, with its apex a rise which connects with the mullock-pass reticulation.(Sce 1 showing this reticulation in diagrammatic form.)

Jan 1, 1927

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

Jan 1, 1993

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By Paul W. Johnson

A computer program for calculating capital and operating costs from material and energy requirements and equipment costs for use in preparing cost estimates for metallurgical process evaluations has been written by the Bureau of Mines' College Park process evaluation group. The program permits rapid recalculation of processing costs when changes of data or equipment are desired, and produces tables of capital and operating costs suitable for publication. Equipment cost summary tables for each process section end supplemental information for input-data checking is included in the computer printout. The program is written in Fortran IV except for several subroutines which are written in machine assembly language for the IBM 7094.3 With a few modifications, the program can be used on other computers.

Jan 1, 1969

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By S. E. Cook

This article uses the case of the Royal Bafokeng Nation to argue that royalties and dividends from mineral resources, if managed well, can provide direct benefits to the surrounding community even while the state collects its share of mining revenues through taxation. The key to this model is the effective management of the resource income flowing into community coffers. Where some of this income may fund urgent interventions in the community, a portion of the income can also be used to establish an intergenerational wealth fund to meet the needs of future generations. As a depleting resource, minerals like gold and platinum are not a sustainable source of income, and must be replaced over time by more regenerative income streams. These strategies and dynamics are manifest in the Royal Bafokeng Nation?s status as both community and quasi-municipality, a labour hosting and a labour sending community, a mine operator and a mine owner. The Royal Bafokeng Nation also owns one of South Africa?s largest community-based investment companies, which channels revenue derived from platinum deposits into a broad investment portfolio that in turn funds an aggressive social development program for 150,000 people living in twenty-nine rural villages.

Jan 1, 2013

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By S. K. Chan, C. Badeen, S. Goldthorp, H. Feng, I. Alilovic, R. Turcotte

Over the last few decades, water-based explosives and their precursors, despite their apparent insensitivity, have been involved in a number of accidents around the world. A large proportion of these accidents occurred when these emulsions were pumped either for their manufacture, transport, or handling. In Canada, this has led to the development of “Guidelines for the Pumping of Water-Based Explosive”, which state that “using pumping pressures well below the laboratory measured minimum burning pressure (MBP) of the corresponding emulsions or watergels is a good safety practice”. However, in the above document, there is no description on how the MBP should be measured. In the last few years, a research program at the Canadian Explosives Research Laboratory (CERL) in collaboration with Orica has been focused on the development of a validated measurement protocol for realistic MBP measurements.

Jan 1, 2014

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944