Search Documents

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By M. H. Basiri

The application of aluminum matrix composites, due to their unique properties, is significantly growing in the variety of industries such as aerospace and automobile. In comparison to other light metals, such as magnesium and titanium, aluminum is lower in price. These are the advantages that this metal dominates the others. In this research, first by applying the lost foam casting method, the SiCp/A356 composite was cast in the bottom and side gate conditions with 690°C and volume fraction of 10%. Furthermore, the effects of reinforcement particles (60 µm, 75 µm) were examined. The results present the particles distribution in the side gate methods is more homogeneous than the bottom gate casting method. Also, by increasing the particles sizes, the fading rate in the side gate are reduced from 22% to 19%, as well as from 26.4% to 25.4% in the bottom gate. Key words: Carbide-Silicone Particle, Gating System, Composite Micro-Structure, Foam Casting

Feb 27, 2013

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

Geophysical surveys are currently being carried out over mineral prospects all around the Pacific Rim. Many of these surveys are successful in locating mineralisation in porphyry intrusives, mesothermal environments, and epithermal vein systems. A number of examples of surveys in Indonesia and Papua New Guinea are presented, which show the successful application of various geophysical techniques to the discovery of mineral deposits on the Pacific Rim.

Jan 1, 1999

Heap leaching for the recovery of precious metals is a comparatively new and rapidly expanding technology. The practical aspects of heap leaching are described and environmental and economic implications discussed.

Jan 1, 1984

By Hugh Thompson

In mining today, planning is of paramount importance, even more so when one considers that the business margins are reducing, requiring the evaluation of diverse alternatives for the optimal use of scarce resources. Additionally the capital required to approve some projects demands the best planning possible. Modern planning requires that all of the aspects of the business be represented, and not just the planning of the extraction in an isolated form. In order to carry out integrated strategic planning in the mining business one needs to have implemented a culture within the organisation that allows the business to be understood as a interelated system of processes. These processes must be co-ordinated so that they interact properly between each other and so define an integrated plan that optimises the available resources and maximises the benefit to the company. This defined culture should consider the important variables of each activity within the processes, and its’ relevance to the strategic plan. In this sense, this paper shows an example of computer tools used in order to reach the described objectives.

Aug 25, 2002

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

There is a saying, ?If it moves, it vibrates.? This is especially true in our modern industrial environments, where workers use powered tools, machinery, vehicles, and heavy equipment. How workers are affected by these elements of the industrial working environment is a concern of health professionals, govern­ments, and scientists around the world. How to adequately assess the effects of human vibration exposure is an equally important issue. The human body comprises a dynamic structure that is living, intelligent, and complex. Consequently, it is not unreasonable to consider that exposing the body to an array of vibration environments would result in outcomes that are not necessarily simple or easily predictable. Sensations caused by vibration may include nausea, annoyance, discomfort or pain, and exhilaration or pleasure. Many factors contribute to the effects of vibration on humans, including the characteristics of the motion and the exposed indi­vidual, the activities of the exposed individual, and various elements of the environment. There have been attempts to summarize the effects of occupational vibration exposures by simply recommending the avoidance of certain frequencies of vibration or by providing a graphical method, i.e., a single curve displaying all human responses to all frequencies. However, such efforts have not withstood the scrutiny of scientific research and analysis. Thus, attendees and participants at this professional gathering now have the rare opportunity to benefit from the technological advances and new scientific research to enhance their understanding of human responses to vibration that suggest more than a simplistic approach. In the tradition of the First American Conference on Human Vibration (1st ACHV) held in Morgantown, WV, June 2006, the 2nd ACHV provides a forum for scientists, engineers, medical doctors, industrial hygienists, and educators to learn and advance research and education in the specialized area of human body vibration. The conference was organized by the Mechanical and Industrial Engineering Department, University of Illinois at Chicago, with support from the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory. As with the first conference, the 2nd ACHV provides the unique opportunity to learn about the current activities of peers and colleagues and to exchange information on topics of interest such as human response, human modeling, experimental design, sensors, new technologies, and epidemiological studies of human responses to hand-transmitted and whole-body vibration. The conference organizers hope that the publication of these conference proceedings continues to foster new research and technological advances to reduce health hazards associated with occupational vibration exposures.

Jun 1, 2009

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By W. R. ARGYLE, R. A. SHERMAN, Henry Kreisinger, John Blizard, B. J. CROSS, A. R. Mumford

On entering the World War the United States was confronted with the necessity of building in a short time a large number of ships of tonnage adequate to transport troops and war materials to Europe and to carry food supplies to the allied countries, whose merchant fleets had suffered greatly by submarine warfare. The necessity of building ships quickly led to the formation of the United States Shipping Board, which was charged with the duty of developing an efficient organization for the purpose. Such an organization was developed under the name of the Emergency Fleet Corporation; it was under the control of the Government, but could conduct its business in the most direct way, like a private corporation. In order to build the largest- number of ships possible without drawing too heavily on the steel industry, which was already taxed heavily by the production of munitions, it was decided to build wooden as well as steel ships. These ships were built from a few standard designs to enable a large number of duplicate parts to be fabricated in inland shops and transported by railroad to the shipyards on the seacoast, where they were assembled into ships. In other words, the plan was to manufacture the ships rather than to build them. The shops on the seacoast were reserved to make those parts of the ships' equipment that could not readily be transported. The inland shops made the parts that could be transported to the seacoast by railroad. Among the more important parts of the ships' equipment to be standardized were the boilers. As the Scotch marine boiler in large units is bulky and can not be transported by railroad, and as, for the same capacity,much more steelis needed in its construction than for water-tube boilers, a few simple designs of water-tube boilers were developed that inland shops having ordinary equipment could make in large quantities.

Jan 1, 1924

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003