Search Documents

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By William C. Cooley

SUMMARY A review is presented of the state of development of high pressure water jet equipment and of large impact hammers for rock tunneling. Information from the U.S.S.R. is based on published literature and three personal visits. Applicable papers which were presented at the International Symposium on Jet Cutting Technology in Coventry, England in April 1972 are reviewed. Data are presented on continuous jet systems, pulsed water cannons, and hydraulic-powered impact hammers with respect to the specific energy of rock breakage and potential application in tunneling machines. INTRODUCTION It has been estimated that the cost of underground excavation during the period 1970-1979 in 15 countries of the Organization for Economic Cooperation and Development will be over $54 billion, an increase of 104% over the period 1960-1969. It is expected that 55% of the tunneling construction will occur in hard rock (Ref. 1). Present tunneling machines are generally limited to soft and medium-hard rock. When used in hard rock, the cost of replacing mechanical cutter bits is high. Therefore there is a need for improved rock fracture methods which can be applied economically in tunneling machines for hard rock. Water jets and mechanical hammers are two

Jan 1, 1997

By Dean E. Matthews

The concept of a pile for construction is credited to a Neolithic tribe called the "Swiss Lake Dwellers" who lived in what is now Switzerland about 6,000 years ago. They used piling, not for supporting heavy loads as we do today, but for elevation to protect themselves from wildlife. The Romans often used piles, and built many structures, including buildings, homes, bridges, roads and viaducts on piling. The Romans built the first bridge across the Tiber River in Rome on timber piles in B.C. 1620. Homes in the cities of Venice and Ravenna were built on piles from B.C. 100 to A.D. 400. The Romans also built the first bridge across the Thames River in London in A.D. 60 on timber piling.

Jan 1, 2003

The Kaiser Aluminum and Chemical Corp. announced plans to raise June ingot prices by 4 cents to 57 cents per pound. Producers? April value for 99.5 percent unalloyed aluminum ingot was at 53 cents per pound. Domestic merchants last month were quoting the metal at 48-49 cents per pound. Primary aluminum producers began restarting production facilities following the settlement of the coal strike. Noranda Aluminum Inc. recalled workers to prepare potlines for production at its plant at New Madrid, Mo., which had closed February 14, 1978 due to the shortage of coal. Eastalco Aluminum Co. resumed full capacity production at its Frederick, Md. smelter where production had been cut by 30 percent. Anaconda Aluminum Co. resumed full capacity production at its Sebree, Ky. smelter.

Jan 1, 1978

By M. Michael, A. Felber

"Mining activities, especially underground mining operations, create great demands on utilized haulage means which cover a variety of different horizontal and vertical distances. In the course of the continuous optimization of the haulage process, the application of textile machine elements, in particular synthetic fiber ropes, offers new opportunities. Therefore the current level of knowledge needs to be improved based on extensive analyses. For the estimation of the scope of these analyses, different fields of application and occurring environmental influences which have an impact on synthetic fiber ropes during their use in underground mining have to be evaluated. The Chair Underground Mining Methods of the TU Bergakademie Freiberg works on a scientific project concerning the use of synthetic fiber ropes in underground mining operations. This paper focuses on the potential application of synthetic fiber ropes in haulage systems in underground mining and exposes critical influences as an outcome of the working environment. These first investigations are the basis for the development of an appropriate experimental series. SYNTHETIC FIBER ROPES FOR UNDERGROUND MINING OPERATIONS The main idea is to optimize underground haulage means to develop even more economic systems. The new and lightweight design of single machine elements seems to be the first step to accomplish this goal. An example is the lightweight design of shaft hoisting ropes. The commonly used steel wire ropes are very heavy and are endangered to snap due to their own weight when reaching a distinguishing length. Thus they may not or only conditionally be used for deep mining operations utilizing shaft haulage. Ropes made of high-tech synthetic fibers weigh only an eighth of steel wire ropes while displaying the same tensile strength. This relation is shown in Figure 1, based on the comparison of fiber strength and density. This could offer new opportunities for deep mining operations, which are anticipated by many mining companies. /1/"

Jan 1, 2015

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By G. Lipsett, S. Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by allowing assets to be used more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the “productivity paradox,” where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the benefits are in how effectively IT is used. Most business sectors have accepted that re-engineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors, but unique operational processes. The lessons of changing business practice in more common business processes, such as inventory control and customer-supplier relationships, can be adequately transposed into a mine setting. The unique operational processes in mines, in turn, require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manager training simulators. This paper reviews some of the latest IT products and outlines the processes and kinds of change that will be required in order to benefit from these new investment options.

Jan 1, 2009

This Kaiser Engineers report on the feasibility of surface mining on the North Slope of Alaska has considered the quantity and quality of the North Slope deposits with attention paid to the economic, technical, and environmental constraints of the mining systems suggested for the three candidate minesites at Kukpowruk River, Elusive Creek, and Kuk River. Site selection, based on coal rank and quality as well as seam thickness and geometry, also considered demonstrated and hypothetical reserves relative to three mining systems (dragline, shovel, dragline and shovel), mining equipment requirements, infrastructure, and transportation relative to the Arctic environment and costed for potential markets. Throughout the report the delicate permafrost environment has received particular consideration. Recommendations based on the technical, economic, and environmental feasibility of mining the coal deposits of Northern Alaska by surface mining techniques have resulted in two conclusions: 1. The coal deposits can be mined with currently available technology; 2. It is uneconomic to mine these coals given current coal resource estimates, costs, and market conditions. A literature survey is included in appendix.

Jan 1, 1977

Jan 1, 1994

By Joseph M. Kurtak

The Bureau of Mines (Bureau) and the U.S. Geological Survey (USGS) conducted a 4-year (1979-1982) mineral assessment study of the Chugach National Forest (CNF), Ak, as part of the Roadless Area Review and Evaluation (RARE II) Program. The USGS remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. This report describes the results of Bureau work in the central 790,880 acres of the Forest. Copper, with by-product zinc, silver, and gold, has been the major metal produced from the study area as well as from the entire Chugach National Forest. The majority of the copper deposits are concentrated within basaltic rocks on Knight Island but the major producers are hosted by sedimentary rocks on Latouche Island. Approximately 182.6 million lb of copper, 1.5 million oz of silver, and an unknown but substantial amount of gold were produced during a 30 year period. Currently no mines in the area are producing. Inferred, indicated and measured reserves having mineral development potential total 4.6 million tons, with weighted average grades of 1.6% copper, 0.30 oz silver/ton, and 0.04 oz gold/ton.

Jan 1, 2011

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

Underground Mine Drainage may be conveniently divided into two operations:(a) Collecting and transporting drainage water to the pump eastern.(b) Elevating water to the surfacc by pumping.This short paper describes a system which automatically performs operation "a" and which has been developed on the South mine at Broken Hill, under the supervision of the mine foreman, Mr. F. McDonell. Operation "a" does not come under the heading of "subsidiary mine" drainage.SUMMARY(1) All drainage waters are collected by gravity flow into sumps.(2) Automatic control boxes operate syphons which transfer water from level to level to pump cisterns or to feed water service.EQUIPMENTSyphon Control Boar - Constructed of 10 ft. x 2 ft. oregon timber, suitably bolted together and equipped with a Bailey's cistern valve, with copper ball float control, and 12 in. pipcs and fittings forming a syphon (Fig. 1). One of these boxes is placed on each level at the shaft.The valve and float are so arranged that when the float is up (ie, box full) the valve will be fully open, and when the float is down (ie, box empty) the valve is closed. The vertical range between the cxtreme positions can be altercd by lengthening orshortening the adjustable arm of the float. The ideal valve is one...

Jan 1, 1927

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The Bega granite at Whipstick, N.S.W., consists of a granite metasomatically altered to leucogranites and a spessartite-granite. The ore occurs in pipes controlled by jointing and shows evidence of post-depositional tectonic forces.The principal ore minerals are molybdenite and bismuthinite, with minor amounts of uraninite, pyrite, gold, bismuth, joseite A, joseite B, tetradymite, chalcopyrite, arsenopyrite, and skutterudite. The gangue minerals are microcline, albite, quartz, muscovite, and spessartite, with fluorite, chlorite, magnetite, and biotite as accessory minerals.The intrusion of granite was followed initially by ascending metasomatic fluids which penetrated along joints to be trapped in the domed roof of the intrusion to form the leucocratic granite. Iron-manganese-rich fluids metasomatically altered the granite to a spessartitegranite which is associated with the later deposited ore.Quartz veins and dykes of varying composition post date the ore deposition.

Jan 1, 1968

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936