Search Documents

By Ronald E. Hamilton

"An attempt to review the recent literature on comminution reveals at once that the subject has many ramifications and that the applications are so diverse that there are very few general statements which can be made.It. seems reasonable to start classification on the basis of size of material as Input to the comminution process. However, we find that this can only be done in a very imprecise manner.The initial step of breaking rock from its natural state of very large pieces in geological formations into sizes suitable for processing is accomplished by blasting. This step in the process has not been ex-amined in this project except to note that great changes have been made during the last decade or so in the explosives used, and in the method of handling them. We should determine what effect changes in mining methods can have on the need for crushing.The second step in the process is usually primary crushing, performed by gyratory or jaw crushers. The largest chunk which can be fed to a jaw crusher depends on the size of the machine, and should be larger than the largest fragment produced in the miring process. It is obvious that the larger the crusher, the less care required in mining to en¬sure the absence of rocks too large to be crushed. The optimum size of crusher to minimize overall cost of mining and reduction is not at all obvious, and no information on this point has come to light in this investigation.It is rather generally accepted that size reduction is most efficiently done in small stages, and that different machines have different opti¬mum size ranges of feed. For example, crushers are preferred for sizes above about 1"", rod mills for the range between 1"" and 0.1"", ball mills are preferred from 0.1""down to perhaps 10 microns, and vibratory mills, or jet mills, below 10 microns."

Jan 1, 1976

Australia is the world's leading producer and exporter of mineral sands. Despite increased production from some other countries in recent years, Australia maintained its No.1 position in 1988 among world producers of mineral sands concentrates. Production of the titanium minerals -- ruffle, ilmenite and leucoxene, as well as synthetic ruffle -- by the seven companies currently comprising the Australian industry increased in 1988 in response to continuing strong demand for feedstock by the pigment industry. Production of co-product zircon remained at the 1987 level, reflecting declining zircon grades. Exports of mineral sands concentrates increased in 1988; export earnings exceeded $300million. Prices for mineral sands concentrates are now at a historical high and, assuming that the world economy remains strong, real prices should continue to trend upwards in the short term. Exploration in the Eneabba-Cooljarloo region and the Scott River area, both in WA, the Murray Basin, Vic, and the central Queensland coast area, has identified substantial resources of heavy mineral sands. These discoveries have reversed the trend of the early 1980s of falling resources of mineral sands. In 1988, BMR estimated that economic demonstrated resources (EDR) of ilmenite, rutile, zircon and monazite combined was about 72.8 million tonnes. However, a substantial portion of the resources on the east coast are frozen as a result of environmental considerations. The proportion of mineral sands concentrates processed in Australia increased with the commissioning of two new synthetic rutile plants; Australia is now the world's leading producer of synthetic rutile (total capacity 272000 tonnes), most of it for export. Australia's two TiO2 pigment producers have both increased capacity, lifting national capacity by some 70p ercent to over 120000 tonnes/yr. As part of the expansion one producer converted from the sulphate to the chloride process. Other new pigment plants are being proposed for the future.

Jan 1, 1989

By J. D. Jorgenson

?? U.S. domestic production peaked at 120 Mt during years of the Korean Conflict120 Conflict ?? Pellet production increased, as highPellet high-grade ores decreasedores decreased ?? Until 1982 recession, most U.S. iron ore mines owned by steel companiesmines companies ?? Large Canadian iron ore mines brought into production after 1950into 1950

May 1, 2011

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Branch of Editorial Services

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue of the Bureau of Mines List of Publications and Articles describes reports and articles published during the period January 1, 1980, to December 31, 1984. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3 from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 and from January 1, 1975, to December 31, 1979;6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1980,7 from January 1 to December 31, 1981,8 from January 1 to December 31, 1982,9 and from January 1 to December 31, 1983. 10"

Jan 1, 1985

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By O. N. Sikazwe

The Nchanga Cu-Co ore deposit of the Zambian Copperbelt, is hosted in Neoproterozoic siliciclastic-carbonate sedimentary rocks, and it consists of two orebodies: the Lower Orebody (shale) and the Upper Orebody (arkose). Refractory Cu ores present in the Upper Orebody comprise 150 Mt with average 0.87% Cu, and are characterized by inadequate recovery of copper by leaching. This materials characterization study, conducted on refractory ore samples from the Upper Orebody using optical microscopy, QEMSCAN®, and microprobe, has shown that copper occurs mainly in biotite, phlogopite, malachite, pseudomalachite and goethite. QEMSCAN® has quantified the abundance of each phase and total Cu deportment in each phase.

Jan 1, 2008

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By E. Harris

Frithia humilis is an endangered succulent plant species. Its distribution range overlaps with the coal fields of Mpumalanga and it is therefore threatened by opencast mining activities in particular. One of the 11 known populations of F. humilis was translocated from a licensed coal mining site to three suitable receptor sites within the species? distribution range. A longterm monitoring programme was initiated to track the progress of the newly established populations. Temporal trends in population demography, size classes, and fecundity were recorded. Population numbers of size classes fluctuated annually. However, flower frequency increased over time and seedling recruitment contributed significantly to population growth. Receptor sites with similar geological conditions to the donor site had more persistent cohorts, which suggest that such sites should receive priority during the translocation of endangered edaphic specialists. This study not only confirms that a Frithia humilis population can successfully establish after a translocation, but also serves as an important baseline for future comparative purposes to gauge the long-term success of the translocation effort.

Jan 1, 2014

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Effect of High Power Nanosecond Electromagnetic Pulses on Selectivity of Pyrite from Arsenopyrite

Sep 13, 2010

By P González, E Córdova, E Faundez

An integrated mine system must be capable of displaying and reporting valuable information that can be used to easily understand, manage and take action on the key parameters being reported.One of the key aspects of integration is the standardisation of the mine information up to a level capable of adapting the main characteristics of past projects at the mine and enforcing the same or higher standards for newer projects being developed.At the El Teniente mine, photogrammetry is used to map the advance of horizontal developments, and the constructed 3D representation of each face is then used by the geologists to obtain structural information about the areas being photographed.The mine realised that valuable mining information could also be extracted from the photogrammetry being applied, with three possible areas of development envisioned.The first area was creating a link between the developments being planned on a yearly and monthly basis and matching them with plan sections of the 3D developments of the system to account for any deviations.The second area was to use vertical sections of the 3D developments to estimate the overbreak of the excavations in different areas of the mine.The third area was the provision of a more detailed analysis of the sections so that they could provide information on the thickness of the shotcrete being applied.This paper presents the different alternatives being used and examines how the project is currently being developed and managed at the mine. It also looks at the challenges associated with implementing the reporting platform and the results being obtained.CITATION:C&#243;rdova, E, Benado, D, Gonz&#225;lez, P and Faundez, E, 2016. Mine planning information from photogrammetry sources at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 653–658 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016