Search Documents

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980

The Torington Lodes.This paper describes investigations into mineralogical, petrological and structural associations of cassiterite in occurrences of economic value. The work was carried out in three mines, during a number of years, in the hope that the, data collected might be helpfulin the search for occurrences of cassiterite in stanniferous zones and reduce unproductive exploratory work. Tin-bearing lodes at Torington, in the New England district, New South Wales, have been worked since 1880, and the locality is the most important centre of lode tin occurrence in the, State. The township of Torington is 18 miles westerly from Deepwater, a station on the Great Northern Railway, 446 miles from Sydney.The tinfield forms part of the Mole Tableland, which has an altitude between 3,000 ft. and 4,000 ft. above sea level. The country rock, in which the stanniferous lodes occur, is granite of Permian age, which has been intruded into Carboniferous claystone. An inlierof claystone is exposed to the west of the stanniferous area, 'and in it, close to' its contact with the enclosing granite, are occurrences of wolfram and bismuth. These minerals, together with chalcopyrite, pyrite, arsenopyrite, zinc blende, galena and molybdenite, in very small quantity, are associated with cassiterite in lodes traversing the granite, particularly near the claystone, but decrease in amount with distance from the contact. Their occurrence is sporadic and usually causes no trouble in dressing the cassiterite concentrate, the final product containing less than 1% of total penalisable impurity. In Curnow's mine, pyrite, galena and molybdenite have been observed at 700 ft. from surface.The granite is of the biotite type and its structure may be divided into four groups, or classifications, arising from segregation processes during cooling and consolidation. The four classes, in order of extent of distribution, are:1. Granite of normal type, in which the constituent quartz felspar and mica, have a particle size approximately 14, in.2. Porphyritic granite, in which the felspar particles are from % in. to lin. in size, that of the quartz and mica approximately % in.3. A fine-grained granite, in which the particles of all constituent minerals are % in. or less in size;4. A rock of highly siliceous ground mass containing very small particles of felspar and almost negligible biotite.Type 1 is the general type of granite in all mines of the field; types 2 and 3 may occur as large masses, or all three classes may merge rapidly one into the other, and all be disclosed in 20 ft. of driving. Usually, however, the segregations are massive, but are not associated with any special horizon. For instance, a mass of porphyiiticgranite extends from surface to a depth of 440 ft., for a distance of 350 ft. south from the New England main shaft. The upper levels of Curnow's mine, 14" mile south-east, are in normal granite, but a restricted mass 'of porphyritic granite occurred between Nos. 5 and 6 levels, or 400-500 ft. below the collar of the shaft...

Jan 1, 1950

By M. P. Valoski

Mine fires and/or explosions continue to occur. While these are unusual events, they comprise emergency situations. Whenever one of these events occurs, the Mine Safety and Health Administration (MSHA) responds with specially trained teams, mine fire experts, sophisticated scientific instrumentation, and trained instrument operators. In order to analyze mine air samples on-site, because time is of the essence, MSHA has a Mobile Gas Laboratory. The laboratory, which is stored near Pittsburgh, is totally self-contained. Sending air samples to a laboratory would take too long. Mine fire experts need the results of the latest analyses as soon as they are finished. The mobile laboratory is housed in the box of a diesel truck. Benches line both sides of the laboratory. Gas chromatographs are mounted on the benches. There is sufficient bench space for multiple bench top gas chromatographs. These instruments and their controllers are shock and vibration isolated to protect them during transit. The mobile laboratory can operate using on board diesel generators or line power. An uninterrupted power supply (UPS) supplies power to the instruments while switching from generator to line power or visa versa. Therefore, analysis of samples can proceed without interruption if a power failure would occur. In the rear of the mobile laboratory are racks that hold compressed gas cylinders. These cylinders contain carrier gas and compressed air. An air compressor is housed under the laboratory to operate the gas chromatograph actuators. Within several hours after arriving at a mine the instruments have stabilized and have been calibrated. The mobile laboratory is ready to begin analyzing air samples. The mobile laboratory has proved itself at many mine fires and explosions since its purchase.

Jan 1, 2009

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By F. K. Shelton, J. C. Stah, Ruth E. Churchward

A study of the hydrometallurgy and electrowinning of cobalt from various domestic ores has been in progress at the Boulder City, Nevada, Experiment Station since February 1940. Previous reports covering certain phases of this investigation have been published. This report covers the research and pilot-plant work on the production of cobalt metal from cobalt-copper ores from the initial experimental work on crude ore through continuous operation. The ore types were from the Blackbird District, Lemhi County, Idaho. The initial tests were made with concentrated ore which was received by air mail and these experiments were expanded both in size and scope. After the laboratory was continued, improved, and extended tests were reported. Sufficiently advanced, a continuously operated plant producing 250 pounds of electrolytic cobalt per day was operated from June 15 through July 15, 1944.

Jan 1, 1948

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009