Search Documents

By Roger M. Sherman

[Investigation of mine land characteristics, evaluation of irrigation systems, and evaluations by the mining industry, determined that irrigation is a feasible method for aiding revegetation of coal mined lands in western arid and semi-arid regions. The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid set irrigation. Irrigation should be supplemental by complimenting natural precipitation and be should implemented on a temporary basis.]

Jan 1, 1980

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

Burr Mineral Resource has: ?Grade / Thickness / Tonnage ?Dry Caprock ?Low Carnallite ?Low Clay / Insolubles ?Flat & Continuous Deposit ?Proper depth

May 1, 2009

By T. R. Curr, W. A. Gericke, J. Basson

South Africa is a leading player in the international ferro alloys industry. Historical factors that have contributed to this dominant position include an abundance of natural resources and relatively low cost electricity. A number of relatively recent developments are potentially threatening this position. These include new legislation affecting the mining and minerals industry, a shortage of some types of suitable reductants, depletion of surplus electricity generation capacity with resultant threat of real escalation of electricity prices and pressure resulting from the recent strengthening of the South African Rand. The industry is addressing these challenges in a number of ways to ensure long-term viability. Some of these measures include investments in more efficient technologies that have economy of scale benefits and are less dependent on expensive reductants and electricity. Local macro-economic impacts include new legislation regarding ownership of enter-prises, mineral rights and royalties on mineral sales, development plans for port and rail infrastructure, as well as initiatives to expand electricity generation and coke production capacity. The fundamentals for being a successful ferro alloy producer are still largely in place for South African producers. Therefore the South African ferro alloy industry will remain competitive and is well placed for continued growth in line with the international growth in ferro alloy demand. The industry should emerge leaner, more efficient and ready to respond to any future demands of the industry. This paper will cover the present status of the industry, the factors that are impacting thereon and a view on its future outlook.

Jan 1, 2007

Mr. BRADFORD said :-On assuming this chair, which has been occupied by so many gentlemen of conspicuous ability; my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year.When considering the subject matter of this address to you to-night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion. Next I turned to a consideration of whether a discourse on the theory and practice of iron and steel would be of interest.I, however, banished this idea also from my mind, because it appeared to me that you have already had a surfeit of this on your visits of inspection to our local industries and I did not want in any way to be held responsible for the iron entering into your souls! I therefore propose, with your kind consideration, to address you on other subjects of common and vital interest to all.My first words and thoughts turn on the absolute necessity of eliminating waste in our methods. If we are to succeed in our...

Jan 1, 1926

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

Concentrations of bright green material in the "Golden Mile" of Kalgoorlie, which carry particularly high gold values, are known locally as "green leader".This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the "green leader".

Jan 1, 1977

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By Jorge Díaz A

El presente texto revisa los métodos utilizados en las minas de tajo de abierto como son la perforación, disparo y seguridad y así mejorar los standars y el rendimiento futuro en la industria minera. Respecto al primer método empleado, se analizan los factores que afectan el rendimiento de brocas y cómo dicho factores varían, impidiendo la adaptación de prácticas universales de perforación. Asu vez, estos mismos permiten seleccionar el tipo de broca adecuado y mejorar el máximo rendimiento del mismo. En cuanto la voladura y los explosivos, se revisan las variables fundamentales que ejercen una influencia sobre el resultado de un disparo y así realizar un estudio comparativo de los agentes explosivos en uso, tratando de interpretar el mecanismo de la explosión y a la vez aplicarlo a las diferentes formaciones presentes en Cerro. Finalmente, se describe la organización del sistema de seguridad y las obligaciones de este comité en la industria minera.

Aug 20, 1965

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By G. M. Kintz, Charles B. Carpenter, G. W. Jones

"INTRODUCTION At 9:12 a. m. on April 16, 1947, the ammonium nitrate cargo in hold 4 of the S. S. Grandcamp, a 7,176 gross-ton Liberty ship owned by the French Government, detonated at pier 0 of the Texas City Terminal Railway Co., Texas City, Galveston County, Tex.This detonation was the first of a series of explosions and fires that took the lives of approximately 600 persons, injured 3,000 other persons, and caused a property damage and business loss that will exceed $58,800,000. It has been estimated that the life, accident, and workmen's compensation insurance loss will be $8,200,000.At 1:10 a. m. on April 17, 1947, the ammonium nitrate cargo in hold 5 of the S.S. High Flyer, a 6,214-gross-ton Liberty ship owned and operated by the Lykes Bros. Steamship Co., Inc., detonated at pier L. This explosion materially increased the property damage caused by the first explosion, in between 50 and 100 persons, and is believed to have taken the life of only one person.The exact number of casualties resulting from the Texas City disaster may never be known. On June 22, 1947, 65 days after the explosions, the red Cross and the Texas Department of Public safety repoted:,""Identified dead, 405; unidentified dead, 63; believed missing, 100; injured, 3,000; hospital¬ized, 600; still in hospitals, 37."""

Feb 1, 1948

Six simulations by the Mpnte Carlo method employing both classical and geostatistical techniques are presented for the determination of the probability distribution of the in situ value of a coal seam. To avoid the problem of qualitative estimation of parameter variability in the calculation of an arbitrary seam value, only data values from borehole information were used to quantify the variation in four coai seam parameters.The method which is suggested as being the most appropriate is a particular geostatistical approach that employs the best linear unbiased estimate and the error of estimation for a number of two dimensional blocks. The results indicate that the variance of the coal seam unit value may be much higher than that indicated by the classical approach because of the spatial variability that is properly incorporated in the geostatistical approach.The model used in the Monte Carlo simulation to determine the economic value of a coal seam can be extended to incorporate all those parameters which are necessary for a true estimation of the probability distribution of the coal seam value. A time value concept for discounting can also be incorporated to optimize the economic return of a coal mining project.

Jan 1, 1983

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By C. R. Landis

The Wyoming bentonite industry continued its run of stable, if not strong, growth in its complex markets. Growth at the macroscale was fueled by a strong domestic economy, the weakening of the U.S. dollar in the global market and strong worldwide global demand. Challenges to the benchmark of the industry were rapid and saw ongoing increases in raw material costs(pallets, bags and additives), higher energy costs and higher overall transportation costs for all modes of movement. Exports continued to be assisted by dollar depreciation (5 percent to 10 percent) from January 2004to January 2005. This depreciation followed the significant weakening of 2003. And it was most favorable during the pullback in fuel and shipping rates in the second half of the year.

Jan 1, 2005