Search Documents

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By John E. Lens

How much trouble can narrow vertical fissures in bedrock cause on a shallow bedrock site? Enough trouble so end-bearing H-piles range between 8 and 100 feet long in a single pile cap and tiebacks range from 40 to over 100 feet long within a 10 foot wall span. Sloped bedrock surfaces also complicated the tieback installation as the drill casing followed the sloped rock surface while drilling and caused unanticipated bending (and sometimes breaking) of the drill string. Warned via pre-construction rock probes and cores reaching over 80 feet deep at the Winooski, Vermont project site, the design and construction team expected anomalies in pile driving and tieback drilling due to fissures in the bedrock filled with soil and weathered-rock. The degree of abruptness in the variability in the rock surface, and its impact on pile driving and tieback drilling were less predictable. Close monitoring of pile and tieback installation, redesign of pile caps, and lengthened tiebacks overcame these anomalous fissures. This paper shares the lessons learned for overcoming these geologic challenges to benefit designers, contractors bidding the work, and ultimately, the owner, with lower contingencies.

Jan 1, 2006

An assessment of methods currently available for the accurate determination of low concentrations of platinum in ores and mineral concentrates indicated that prior treatment of the sample by fire assay procedures is necessary. To enable rapid determinations to be carried out, instrumental methods applied to the metallic bead produced from the fire assay treatment have been evaluated, considering maximum flexibility for concentration variations, minimum chemical operations, and adequate sensitivity.Atomic absorption spectrometry proved suitable, giving solution determination limits of 0·4 p.p.m. Pt, 0·1 p.p.m. Pt, or 0·06 p.p.m. Pt under various extraction conditions using aqueous and organic agents. Thesedetermination limits related to 1 assay ton of sample (32·67 g) produced easily readable and accurate readings within the range of platinum contents (0·03-2·0 p.p.m.) of economic interest in deposit evaluation and prospecting. The technique shows promise of also being suitable for determination of palladium and gold.

Jan 1, 1970

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

Smarter Gravity Separation Using the Kelsey Centrifugal Jig With relatively coarse grained and easy-to-process ore sources rapidly dwindling, smarter techniques are becoming more necessary for the continued success of mineral processing operations, while increasing environmental pressures also require more environmentally friendly solutions. Gravity concentration has long been employed to pre-concentrate minerals using water, reducing or eliminating the need for less environmentally friendly processing techniques such as flotation. Conventional gravity recovery devices however, operate in a 1 g environment with limited efficiency in the separation of fine particles of heavy and gangue minerals. More recently developed centrifugal concentrators operate in a multi-g environment and enable finer heavy minerals to be recovered, but also exhibit limited separation efficiency due to the separations being based on solid particle mass differentials. Further enhancement of gravity separation has been achieved using the Kelsey Centrifugal Jig (KCJ), which also operates in a multi-g environment, but separates minerals on the basis of specific gravity differentials, using 'ragging' media and a pulsation mechanism, which maximises the effect of differential particle accelerations. This enables the efficient separation/recovery of minerals down to a particle size of ~6 ¦m and/or separation of minerals with a low specific gravity differential. This paper presents details on the principals of operation of the KCJ, recent improvements in the technology and recent developments in modular KCJ plants, as well as some KCJ application areas, which offer smarter, environmentally friendly processing opportunities for the mineral processing industry.

Sep 13, 2010

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962