Search Documents

By J. Drelich, C. L. White, Ch. Zhou, W. M. Cross, E. T. Zellers, E. M. Nadorny

A laser-based particle deposition (LBPD) technique has recently been developed at Michigan Technological University for patterning mesostructures made of nanoparticles and their clusters. The LBPD technique makes use of laser induced optical forces to transport and pattern nanoparticles on a variety of conductive and non-conductive substrates from nanoparticle-in-liquid suspension. A weakly focused laser beam is used to confine and propel particles along the laser beam. Confinement is accomplished by forces due to optical field gradients that act on polarizable particles and tend to move them to axis of the laser beam. The force propelling the particles along the direction of the laser beam arise from momentum conservation of photons scattered from the particles. In this paper, this novel LBPD technology is briefly reviewed, and several examples of patterning are presented. The size and morphology of mesostrips produced from gold and polystyrene nanoparticles, under a range of deposition conditions, have been characterized by optical microscopy, atomic force microscopy, and scanning electron microscopy. The results presented here demonstrate that gold and polystyrene nanoparticles deposited by LBPD can form clusters of particles. When deposited at an appropriate rate, such clusters can form multilayer mesostrips of high particle density. One goal of research on such systems is to fabricate arrays of parallel lines made up of colloidal particles having a range of surface functionalities. Such arrays have potential for application as novel microsensors for environmental sensors.

Jan 1, 2003

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By H. A. Dakin

"An introduction to the metallurgical requirements of the Flin Flon concentrator reveals the magnitude of ore blending which is required in its operation of three flotation circuits. The resulting variability in flotation heads which has in-creased the separations complexity justified the development of an on-line analysis system.This paper provides a summary of the development and operation of that system. Particular attention is devoted to the problems encountered and where possible their solutions; as the requirements of accurate information and minimum downtime of the sampling system and x-ray analyzer are considered essential. The addition of a recess central computer has provided information in a more easily understood form and as well has allowed the start of automatic reagent control.An indication of the on-line analysis system's value to the concentrators' operation is provided by an examination of the plant in metallurgical data and reagent costs in previous years.The metallurgical plants of Hudson Bay Mining and Smelting lie adjacent to the city of Flin Flon on the Manitoba-Saskatchewan boundary. Plant operations commenced in 1930 treating copper-zinc ore from the local mine. In recent years ore bodies near Flin Flon and in the Snow Lake area, about seventy-five miles east, have been brought into production.By the beginning of 1973 the number of producing mines had increased to nine; with all the ore being handled by the Flin Flon concentrator. Figure l, showing mine ore assays during 1973 indicates the variation in metal content possible."

Jan 1, 1974

By E Skinner, G Lane

Project delivery strategies are determined by project context, business case requirements, scale of project, market conditions, ownerÆs capability and preference, contractorÆs experience, resource and skill availability, project location and type of project or facility.Successful project management requires the setting of coherent, effective and realistic business objectives and success criteria. The management team needs to lead, prioritise, resource, align, plan, track and communicate the processes that enable the realisation of these business objectives and success criteria.For any given project there is a unique balance between selection of a simple project delivery strategy that minimises interfaces and a complex strategy that necessarily engages the use of expertise and experience from numerous parties. The right balance for a project between these "book-end cases" is a function of how the project owner or managing contractor defines its objectives and chooses to manage risk, cost, schedule and project quality, in the context of the conditions affecting the project.Selection of an effective project delivery strategy requires a detailed appreciation of the range of external and internal environmental / shaping factors which influence the project. These factors include the project constraints imposed by the business, market or operational environments and the selection of an effective mix of primary (head contract), secondary (mix of vertical and horizontal packages) and tertiary (type of individual contract) strategies. The selection of the primary, secondary and tertiary strategies also shapes the project, the size and responsibilities of the ownerÆs team and the framework for delivery of outcomes.How does an owner or prime contractor decide? What is the optimum for a given project? Those with operations management backgrounds will have different views to those with project and construction management backgrounds.Is the simplest practical approach the best approach? Each and every interface needs to be managed.The owner will want a very experienced team that is engaged directly with the owner. The team will have a track record of successfully performing projects using contractors skilled in their respective disciplines and selected using competitive tendering on brilliantly designed scopes of work and good contract terms, with a fully defined project scope and appropriate schedule, for which all significant risks have been addressed and no scope changes are outstanding. Budget and schedule will be expected to have been developed with a full understanding of the scope, situation, risk management requirements etc.The problem is that these conditions rarely exist. The challenge in selection of a project delivery strategy is to resolve how best to address the inadequacies between the ideal case and the present reality. The mechanism for addressing the inadequacies defines the likely outcome of the project.CITATION:Lane, G and Skinner, E, 2013. Project delivery, in Proceedings MetPlant 2013 , pp 50-65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Mark Kennedy

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation?s cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2013

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By A Giblett, T J. Napier-Munn

This paper presents the results of a test program evaluating the impact of sample mass on the precision of Stage 1 gravity recoverable gold (GRG) test results. Four ore types ranging from low to high GRG contents were the focus of testing. A method to predict the influence of sample mass on the confidence limits of the Stage 1 GRG test result is demonstrated. The results suggest that although small samples tend to overestimate Stage 1 GRG in samples with low gravity gold values due to higher mass pull to concentrate, such samples can give acceptable estimates of the Stage 1 GRG content with focussed sample treatment protocols.CITATION:Giblett, A and Napier-Munn, T J, 2015. Measuring the influence of sample size on the precision and accuracy of gravity gold estimation, in Proceedings MetPlant 2015, pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D. H. Horswill

The paper point out considerating how mining activities contributed to sustainability, it is important to consider how exploitation of a finite resource can be regarded as sustainable. The now well–recognized concept of sustainable development holds that society’s pursuit of development that meets current needs should not compromise the ability of future generations to meet their own needs. Sustainability, then, contemplates multigenerational enjoyment of a quality of life that includes social and economic benefits and a healthy environment in which to live. In this sense, the benefits of our activities must always exceed the risks. Many other companies are also making significant inroads along the path to sustainability.

Sep 13, 2001

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

Comparative Studies on Balls Versus Spheroidal Tetrahedrons Working Media to Ore Grinding in an Industrial Drum Mill

Sep 13, 2010

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By G. B. Harris

It has long been appreciated that chloride chemistry has a number of advantages over the more traditional sulphate route for both extracting and separating metals. Modern materials of construction, coupled with the development of a more cost-effective and efficient hydrochloric acid regeneration technology mean that chloride-based processes are now more competitive and attractive. Such processing routes are able to recover more of the contained metal values in a feed, including iron in a benign and/or marketable form, and particularly the so-called rare and rare-earth elements which are increasing in demand in our electronic age. These factors, therefore, add appreciably both to the overall economics of a project, but also offer a much more sustainable approach to our dwindling natural resources. Additionally, chloride-based flowsheets can be much more environmentally-friendly, offering practical alternatives to two of the biggest headaches faced by the industry, namely cyanide usage and the generation of red muds. This paper presents a brief theoretical background, focusing on the latest developments of ferrous iron oxidation and the low-temperature, selective hydrochloric acid regeneration process, which is the key unit operation for any chloride flowsheet, and discusses in general the advantages of the chloride approach. Several recently-developed flowsheets, which have been tested at the miniplant level, are presented for gold, base metals, titaniferous magnetites and lead-silver ores wherein the advantages of considering a chloride approach are highlighted.

Jan 1, 2014

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004