Search Documents

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By P. Shahinian, M. R. Achter

P. Shahinian and M. R. Achter (U.S. Naval Research Laboratory)—We should like to point out another instance where concentration of impurities in grain boundaries led to an embrittlement. In this case an impure nickel (99.8 pct) developed many more in-tergranular cracks during creep in a nitrogen atmosphere than in vacuum.5 In comparison high-purity nickel (99.99 pct) exhibited a much smaller atmosphere effect. We concluded that the interartion of the nitrogen with nitride-forming impurities concentrated at grain boundaries promoted inter-granular cracking.

Jan 1, 1965

I have the honor to submit herewith the report of the Secretary for the year 1915 showing the principal activities of the Institute: Meetings.-The 110th Meeting, including the Annual Business Meeting, was held in New York City, Feb. 15 to 17, 1915. The full report of this meeting is given in Volume LI of the Transactions. The number of papers presented was 53, and the attendance was 357 members and guests. The 111th Meeting was held in San Francisco, Cal., Sept. 16 to 19, 1915. Sixty-eight technical papers were presented, and the attendance was over 400 members and guests. The full report of this meeting is given in the Bulletin for December, 1915. Local Section.-A new, strong Local Section of the Institute, with head-quarters in Arizona and known as the Arizona Section, was formed during 1915. Affiliated Student Societies.-Three new Affiliated ,Student Societies were recognized in 1915 consisting of the Pick and. Hammer Club of the University of Oklahoma, Mining and Metallurgical Club of the Univer-

Jan 2, 1916

By C. G. Durdaller, W. H. Robinson, G. M. Pound

The nucleation rate of the a (pay) to 0 (white) tin transformation was measured as a function of temperature and a tin particle size using an X-ray diffraction technique. The powder specimens of a tin were essentially monodisperse and the small dinzension of the particles of these specimens was varied from 13 to 75 p. Several types of nucleation sites of differing potency were fbund to be operative in the nucleation process, but it could not be determined whether these sites were on the free surface of the tin particles or within the volume. Assuming that they were on the free surface, the average density of the most potent sites was calculated to be 2.5 to 5.3 x 10&apos; sites per sq cnz through the application of a Poisson distribztion finction to the isothermal data. Analysis of the temperature dependence&apos; of the rate constmts at a given fraction transformed suggests that the active sites are regions of higher free energy and not catalytic interfaces. Appreciable induction periods were observed at the lower temperatures of transformation. Experimental studies1 of solid-solid phase transformations have led to the belief that the new phase nucleates at structural imperfections. The purpose of the present work was to learn more about the mechanism of nucleation in solids and the nature of the singularities at which nucleation occurs. In this investigation nucleation rates in the isothermal transformation of gray to white tin were measured by an X-ray diffraction technique using essentially monodisperse powders of gray tin. This particular phase transformation was chosen for study because it presented fewer experimental difficulties than most others. The experimental temperature-control problems were minimal because the two phases coexist in equilibrium at 13.3"C, and measurable transformation rates occur at temperatures only slightly above room temperature. The growth rate of the P phase into the a2 is sufficiently fast to make the measured transformation rate equivalent to the nucleation rate, provided that the particle size of the samples is small enough; for the experimental temperatures used in this study, the particle diameter must be less than 100 p. EXPERIMENTAL TECHNIQUE The P tin used in this study was obtained from Capper Pass and Son Ltd., North Ferriby, Yorkshire, England, and was of 99.999 pct purity. It was transformedS to the a phase and ground into a fine powder in an agate mortar. This powder was separated by a Roller air classifier into seven fractions whose dimensions, as determined by microscopic measurement of many thousands of particles, are given in Table I and whose distribution of size within each fraction is given in Figs. 1 and 2. The shape of the particles was roughly that of an oblate spheroid,

Jan 1, 1964

* Kennecott Copper Corp. gets Charles R. Cox as president on Jan. 1. Mr. Cox is resigning his position as president of Carnegie-Illinois to take the new post with Kennecott, left vacant by the death of Mr. Stannard in September. •The ECA signed a contract in December to advance X3,600,000 to Newmont Mining Corp. to aid development of lead and zinc mines in French Morocco. The funds are to be repaid in lead and zinc for the United States&apos; stockpile over a period of seven years. The mines are owned by the Societe des Mines de Zellidja, with which organization Newmont is associated. • Under the direction of John M. Brooks, Jr., general manager, the Matahambra mine in Cuba, will probably produce sufficient tonnage to make 4 million lb of copper per month during 1950. The grade is presently running between 7 and 10 pet. •S. H. Ash reports that the fatality rate per million-man-hr for the anthracite industry for 1949, through November, is 0.78. This is 15 pct better than that achieved during 1948, which was the lowest fatal injury rate in coal mining history. The first full year on record without a major disaster was recorded in 1949 (p. 34). •The Atomic Energy Commission has authorized the production of 200 lb of uranium metal for use under AEC license in non-Commission research projects. •A national survey of projected 1950 purchases of new machine tools, machine tool accessories, materials handling equipment, etc., just completed by the American Society of Tool Engineers reveals that, of the companies reporting, 80 pct state that they plan to buy either more equipment or the same amount as in 1948. • Armour Research Foundation is conducting investigations for the use of clay and shale deposits to make lightweight aggregates. The material is heated until it expands and forms material suitable for mixing with cement which it is hoped will be lighter, stronger, have better insulating qualities and will lower the cost of concrete. •In the first six months of 1949 the bituminous coal miners&apos; average hourly earnings were $1.94 -as compared with X1.392_ national average for all manufacturing. Average annual earnings of full-time employees in the bituminous coal mines in 1948 were $3387 as compared with $2809 for all industry. •LaSalle Business Bulletin reports: "year ends on a rising trend in industry and trade ... nearly record-breaking demand from almost all sources keeps business high... most indicators but little below postwar peak... forces keeping activity high arestill powerful--changes in general business conditions likely to be slow and moderate." •Office of Internal Trade of the Commerce Department requests that technical data significant to the national security which is to be sent outside of the United States be submitted to it for an official opinion on the desirability of transmitting such information. This voluntary compliance program is part of our national security control. • Blast furnace slag reduced to 12 to 16 mesh is being used for sanding track at the Mont Coal mines of Armco. The slag replaces silica sand which caused silicosis. It has proved so effective and cheap that tests are being made to use the slag for rock dusting.

Jan 1, 1950

By P. W. Bridgman

THE thesis of this article is that the age of Newton is now coming to a close, and that recent scientific discoveries have in store an even greater revolution in our entire outlook than the revolution effected by the discovery of universal gravitation by Newton. The revolution that now confronts us, arises from the recent discovery of new facts, the only interpretation of which is that our conviction that nature is understandable and subject to law arose from the narrowness of our horizons, and that if we sufficiently extend our range we shall find that nature is intrinsically and in its elements neither understandable nor subject to law. The new experimental facts are in the realm of quantum phenomena. Comparatively little has been written for popular consumption about this new realm which has opened in the last fifteen years. The man in the street has been much more interested in relativity, which to him has seemed extremely interesting and revolutionary. Occasionally, however, there has filtered down to him the news that nearly all the theoretical physicists are occupied with a new order of phenomena which they find very much more exciting and revolutionary than any in the realm of relativity. For after all is said and done, the practical effects of relativity, measured in ,dollars and&apos; cents or in centimeters and grams, are exceedingly small, and require specially de- signed experiments executed by men of the highest skill to show their existence at all. The phenomena with which quantum theory deals, on the other hand, are of the greatest practical importance and involve the simplest aspects of everyday life. For example, before the advent of the quantum theory no one could explain why a tea kettle of water boiling on the stove should not give out enough light in virtue of its temperature to be visible in the dark; the accepted theories of optics demanded that it should be visible, but every burned child knew that it was not.

Jan 1, 1929

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven&apos;t been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By J. F. Gallie

From the standpoint of exploration and new discoveries, South Arkansas had a discouraging year in 1944. In January there were 73 untested drilling blocks, and 60 additions were made during the year. Of the total, 65 were condemned by dry holes on or adjacent to them, while 5 proved productive. The latter resulted in the discovery of the Salem Church, Calhoun Wilks, and Strong fields, and the extension of the Village field to the southeast. The year ended with 63 untested blocks, 41 of which were scheduled for tests to the Smackover lime, the state&apos;s deepest oil-producing formation. Geophysical activity in 1944 totaled 164 crew weeks, of which 110 were seismic, 43 gravity, and 11 radioactive (Fig. I), in contrast with 674 crew weeks reported for 1943, of, which 563 were seismic and in gravity, Five seismograph and two gravity crews were engaged in exploration in South Arkansas during January 1944. but only two seismograph crews were working there at the end of the year. In addition, exploratory core drills were used for a total of 38 weeks during the year. The year&apos;s few discoveries, none of which is considered as having added appreciably to state reserves, were the meager results obtained in the drilling of 62 wildcat wells 2000 ft. or deeper. Of this total (a detail of which appears in Table 2), 42 were drilled to the Smack-over lime or below, The average depth of the 62 wells was 5384 ft., as compared with 4992 ft. in the preceding year, while the average depth of the 42 wildcats in the lime was 5913 ft. in 1944. Fig. 2 has been prepared to show all , wells penetrating to the Reynolds oölitic lime. The 1944 dry holes are circled lightly, while discoveries are heavily circled and shown as producers. Smackover lime fields, producing from the Reynolds oolitic lime member, are indicated in black, and the locations of dry wildcat wells drilled prior to 1944 are also shown. Table 3 provides a listing of all Smackover lime wells drilled through the end of 1944. Production for the year was slightly more than in 1943, totaling 29,282,747 bbl., as compared with 27,521,943 bbl. for the preceding year. The increase was 1,760,804 bbl., or 6.4 per cent, bringing production to a peak exceeded only in the 1923 to 1928 period of flush production from the older shallow fields, principally Smackover. The increase was largely attributable to additional development in the Dorcheat-Macedonia, Atlanta, Fouke, Stephens-Smart, Haynesville, and Village fields, little production deriving from 1944 discoveries. These six fields accounted for loo of the 122 field wells drilled during the year. Annual and cumulative production for the producing life of the state are presented graphically in Fig. 3. Fig. 6 has been prepared by the author to show the producing ages and present known productive limits of all fields in South Arkansas. Production data, as usual, are assembled in Table 2, and provide a further breakdown of producing formations in the individual fields.

Jan 1, 1945

By Wesley G. Josephson

THE MINING PROPERTY of the Argonaut Mining Co., Jackson, Calif., is one of the oldest on the Mother Lode. A vein outcropping on a hill in this section could not long elude the eye of the forty-niner, so it was first discovered in 1850. From that time until 1893 the Pioneer mine, as it was then called, limped along under various poorly equipped and financed operators who tried tapping it by trenching and tunneling. Then the Argonaut Mining Co. took over the property and sank the present 65° inclined shaft in the hanging wall of the vein. The mine workings have now reached the 6000-ft. level, which is 5283 ft. vertically below the surface, or just 3 ft. over a mile. The total production of the mine is uncertain, because of lack of early records, but from 1893 to 1932 it is known to have produced in excess of $17,000,000.

Jan 1, 1932

By J. R. Thoenen

IF ASKED whether limestone production was a mining problem I would; not hesitate to answer emphatically in the affirmative. The question, "When is a quarry a mine?" is familiar. The immediate mental picture induced by the thought of limestone production is that of an open quarry. All are familiar with the open pit in the iron-producing districts of Minnesota and Michigan and the open cuts of the so-called "porphyry" coppers of the West. If these are mines, they differ little from limestone quarries in general mode of operation; if quarries, why do they need the attention of mining engineers? During 1923, the United States produced in round numbers 70,000,000, tons of ore. The limestone production of the United States for the same period was something over 100,000,000 tons. In tons, it about equals the oil production of the United States. The uses of limestone are legion. A paper read by a prominent engineer of Chicago, at the meeting of the National. Crushed Stone Association held last February in St. Louis says: "There is no industry in the United States today that is more basic in its operation or by itself controls. more industries. There is hardly a chemical operation, hardly a metallurgical operation or building operation that a crushed-stone man does not control if he will jump in and make the full utilization of it." Some of the many uses are for road metal, concrete, railway ballast, building stone, riprap, and rubble, the manufacture of iron and steel, alkalies, calcium carbide, magnesia, carbolic and carbonic acids, asphalt filler, mineral wool, poultry grit, sulfuric acid, phosphates, nitrates, soap, baking powder, the purification of copper and prevention of coal-mine explosions, to say nothing of the quantities used in the making of lime and cement. It has been said that without iron we would revert to the Stone Age; how much iron would we have without limestone? From the point. of view of the mining engineer, using the term in its broad sense to include geologists and metallurgists, the production of limestone is important because of its occurrence, volume, commercial importance, and the problems presented by its recovery and treatment.

Jan 2, 1925

By Charles Law McCabe, Lyndon H. Everett, Edna A. Dancy

It has been found that the carbide phase present at equilibrium in the system M-H2-CH4, at about 600°C, is MC for the rare-earth metals Ce and Pr. X-ray diffraction analysis showed that the monocarbides have fcc structures with lattice constants of 5.036 + 0.009Å and 5.131 + 0.001Å for CeC and PrC respectively. Gaseous equilibrium measurements were used to calculate the standard free energy of formation of the monocarbides from the elements. for the formation of (+ 1300) for the formation of PrC. THE rare-earthdicarbides, and their crystal structures, have been known for some years,l but only more recently were the carbides CeC,2,3 Ce2C3 2 and CeCS3 reported. In 1958 to 1959, Spedding et al. published work on the lanthanum-carbon system4 and other rare-earth metal-carbon systems,5 proving the existence of M2C3 and MC2, and measuring the lattice constants. They also demonstrated that tri-rare earth carbides, M3C, exist for the rare-earth metals samarium through ytterbium. However, they concluded that the cerium monocarbide reported by Brewer and Krikorian2 and by Warf,3 and given a fcc structure with a lattice constant of 5.130Å bythe former workers, was, in fact, cerium metal with carbon dissolved in it. They were also unable to find any evidence for the existence of Warf&apos;s CeC3, for which no structural details had been given. Even more recently, Palenik22 reported the existence of only M2C3 and MC2, having been unable to find any evidence for the existence of any other rare-earth carbides. There are no published experimentally derived thermodynamic data for the formation of any of these carbides, although Brewer and Krikorian6 have estimated values of for CeC, Ce2C3 and CeC2. The objective of the present investigation was; to determine experimentally the free energy of formation of any of the reported carbides of cerium and praseodymium, through a study of the rare-earth metal-hydrogen equilibrium. EXPERIMENTAL A methane-hydrogen mixture was circulated, in a closed system over previously prepared cerium or praseodymium hydride, and when equilibrium had been attained, the gas mixture was analyzed by selectively oxidizing the hydrogen and condensing out the water formed. The metal hydrides were used as starting material for convenience because, otherwise, the hydrogen in the gas mixture would immediately dissolve in the metals; in addition, the metals would not react with methane alone at the experimental temperature (around 600°C). The circulating system was based on that used by Browning, DeWitt, and Emmett7 for similar studies on iron carbides. It consisted of a quartz reaction vessel, all-glass circulating pump, analysis tube containing copper oxide that could be heated to 300" C by means of a small furnace, a solid CO2-methanol trap, and a double limb absolute manometer, Fig. 1. A cathetometer, capable of reading to 0.005 cm, was used to measure the difference in height between the two columns of mercury. In its final form, the reaction vessel was enclosed in an outer jacket, containing approximately the same pressure of hydrogen as that within, to reduce errors due to diffusion of hydrogen out through the fused silica of the reaction vessel., The circulating system was supplied with

Jan 1, 1962

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By T. L. Joseph

Sulfur balances calculated from operating data covering thirty-five blast furnaces indicate that approximately 92 per cent. of the total sulfur charged enters with the coke, 7 per cent. with the ore, and 1 per cent. with the stone.. Most of the sulfur is carried from the furnace by means of the slag, the total amount eliminated being the product of the slag volume and the percentage of sulfur it contains. Additional sulfur in the charge must be eliminated either by increasing the percentage of sulfur in the slag or the quantity of slag. From relations found between slag volume and coke consumption and sulfur in the coke and slag volume, curves have been prepared showing the relative value of blast-furnace coke as its sulfur varies from 1 per cent. CHARCOAL was the predominant blast-furnace fuel until 1838, when it was found, by the operation of a 2-ton experimental furnace, that anthracite could also be used. This information was a stimulus to the iron industry, particularly in eastern Pennsylvania where anthracite was available at low cost. The production of anthracite pig iron increased steadily and, in 1855, its tonnage exceeded that of charcoal iron. Of the 680 furnaces in operation in 1874, the 226 using anthracite produced nearly one-half the total tonnage. In 1869, the production of coke furnaces exceeded that of charcoal furnaces and, in 1875, coke surpassed anthracite as a metallurgical fuel. In 1907, the output of anthracite pig dropped well below a million tons and its present significance is largely historical. In recent years, the production of coke has gone hand in hand with the production of pig iron and it has gradually attained the position it now occupies as a universal blast-furnace fuel. Charcoal, however, has great merit as a blast-furnace fuel chiefly because of its freedom from ash and sulfur. The harmful effect of the latter and the necessity of keeping the percentage of this element in pig iron at a minimum are well recognized. Other contaminating elements can be reduced to specified limits in the steelmaking process, but the control of sulfur belongs essentially to the blast furnace. The purpose of this paper is to point out the distribution of this impurity in blast-furnace

Jan 9, 1924

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By George W. Maynard

In the Journal of the Iron and Steel Institute for the year 1878, in the account of the proceedings of the annual meeting in March of that year, when Mr. Bell read his paper On the Separation of Phosphorus from Pig-Iron, occurs the following statement, as part of the reported discussion of that paper: " Mr. Sidney Thomas stated that he had succeeded in effecting the almost complete removal of phosphorus in the Bessemer process. Experiments had been carried on at Blaenavon, with the co-operation of Mr. Martin, on quantities varying between 6 lbs. and 10 cwt., and some hundred analyses made by Mr. Gilchrist (who had the conduct of the experiments from the first) showing the removal of from 20 per cent. to 99.9 per cent. of phosphorus in the converter. He believed the practical difficulties in the way had been overcome, and that Cleveland pig might be made into good steel without any intermediate process. He hoped on a future occasion to lay full details before the Institute." I was present at that meeting, and I doubt if any one in the hall knew, either by sight or name, the young man who had dared to rise in that august body and claim that he had accomplished that after which the great metallurgists of Europe had been unsuccessfully striving ever since Mr. Bessemer&apos;s great discovery. I remember distinctly the pitying smile of derision and the stony stare

Jan 1, 1885

By D. M. Francois-Bongarcon

The idea of parameterizing reserves has only been formalized and scientifically applied for a few years. Its most fully developed application, that of open pits, has been operational only since 1976. Two new versions which have just been issued provide a complete solution to the problem and also a powerful tool for mine planning, and they open up a new field of investigation. This paper describes the basic principles for parameterizing reserves, their application for open-pit mines, the algorithm used, the physical interpretation of the results obtained, their economic use as well as the first prospects offered by a complete parameterization in tm of (I. ti), or of the metal price.

Jan 1, 1984

By L. G. Huntley

A description f the geology and conditions affecting the occurrence and mining of oil; also the prospects of obtaining oil in different parts of the country. THE Colombian highlands consist of three parallel mountain ranges (Fig. 1) called respectively the eastern, central, and western cordillera of the Andes. A segment of the range that forms the backbone of the Isthmus of Panama also extends into Colombia, along the Pacific coast, as far southward as the mouth of the San Juan River. These four mountain ranges furnish the key to the varying climatic conditions and vegetation of the country. The river valleys are hot and covered with dense tropical growth. This is also generally true of the coastal plain, although in the northern portion there are some fairly open stretches where cattle are raised and even small districts where semi-arid conditions prevail. The population of this heavily wooded wet lowland depends almost entirely on river transportation for all intercourse. The elevated mountainous plateaus of the three ranges are more open and more generally cultivated; all traffic is by means of horses, mules, and the burro. The canoe and river-steamer transportation systems of the valleys are connected with the highland system of trails and roads by short cross trails and the few short railroads of the country. As these cross trails must pass through the intermediate foot-hill region, where the heavy rainfall reaches its maximum, they are exceedingly bad and the life of pack animals is short. The oil development of the Magdalena River valley is in this intermediate region, between the river and the sierras, north of Bogotá.

Jan 9, 1922

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936