Search Documents

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By Russell B. Cornell, William B. Plank

AT the close of the academic year 1940-'41 the largest number of students ever recorded received their first or bachelor degree in the mineral technology schools of the United States. The total of men thus prepared to enter their professional careers in the mineral industries was 1601, a number nearly 12 per cent larger than two years ago and nearly 75 per cent larger than four years ago. Notwithstanding this increase in the number of graduates and as had been predicted in the preliminary report in February, there was a slight decrease in the total student population of the schools in both the United States and Canada. During the college year 1940-'41, 9133 students were enrolled in the 54 schools of the United States and 764 in six of the seven schools of Canada.

Jan 1, 1941

By J. B. Tyrell

A SHORT time ago I paid a visit to the alluvial gold fields on the tributaries of the Chaudière River in Beauce County, Quebec, in company with A. 0. Dufresne, late manager of the Champs d'Or Rigaud-Veaudreuil, and now Assistant to the Superintendent of Mines of the Province of Quebec. As the conditions under which the gold occurs in this district are not very generally known, and present some interesting features, a brief description of these conditions, and a consideration of the causes which gave rise to them, may be of interest to other mining engineers. During the latter half of last century the country was visited by many mining engineers and geologists, and many references to it may be found in the reports of the Geological Survey of Canada between 1848 and 1911. The most important of these are by J. A. Dresser and J. Keele and the late Robert Chalmers. The Department of Colonization and Mines of the Province of Quebec also published a report with map on the district by J. Obalski. From the earliest times the valley of the Chaudière River formed one of the main avenues of approach to the St. Lawrence in the vicinity of Quebec from the country to the south as far as the seaboard of the States of Maine and Massachusetts. The Indians had a well-known trail along the banks of the stream, and armed troops and foraging parties constantly moved backward and forward along it between Quebec and New England in those insecure times before the ceding of Canada to Great Britain. Even yet the natural advantages of this old military route are recognized, and the government of the -Province of Quebec has now under construction along it a magnificent highway from Quebec to the International Boundary Line, which is to form part of a through highway from that city to Boston; The land along the valley is naturally well suited for agriculture, and about the end of the eighteenth and the beginning of the nineteenth centuries farmers began to go back from the St. Lawrence, and to occupy the higher lands along the upper portions of the Chaudière Valley. This settlement has gone on until now the country is peopled with a prosperous agricultural population.

Jan 3, 1915

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By L. H. Schwartz, S. K. Lahiri, M. E. Fine, D. Chandra

WHILE the yield stress of solution treated Fe-Cu alloys increases rapidly with aging, a precipitate has only been directly observed in overaged samples.'-" This precipitate is essentially pure fcc copper, the E phase. Hornbogen2 suggested that the initial hardening is due to clustering of copper atoms in a bcc iron matrix. Hornbogen was not able to obtain direct confirmation for such bcc clusters by either X-ray diffraction or electron microscopy; however, he did observe analogous clustering in Fe-Au alloys7 where the scattering factor difference between iron and gold is more favorable than that for iron and copper. Fujii, Nemoto, Suto, and Monma4 recently observed diffuse electron diffraction scattering in a 2.5 pct Cu alloy aged at 500°C: for 30 hr. They suggested that part of the diffuse SCattering was due to a modulated structure of 26 to 42 wavelength parallel to the (110) matrix plane. This disappeared with further aging. However, 30 hr at 500°C is well beyond the peak strengthening in this alloy which occurred at less than I hr at 500oc.4 By transmission electron microscopy they could not distinguish between quenched samples and samples aged to maximum strength. The purpose of the present investigation was to try to obtain further confirming evidence for a precipitation stage preceding the formation of the fcc E phase. Change in Young's modulus was selected for study be- EXPERIMENTAL PROCEDURE The Fe-1.67 at. pct Cu alloy was supplied by the U.S. Steel Corporation in the form of a hot forged rectangular bar. The carbon and nitrogen contents of this alloy were 70 ppm and less than 10 ppm, respectively. The samples for Young's modulus measurements were made by cold swaging to & in. diam and cutting to 2 in. lengths. Tensile test samples 1 in. long were prepared by cold rolling to a thickness of 0.012 in. and then machining to gage dimensions of 0.5 by 0.012 in. For Mijssbauer studies, foils 1 mil thick were prepared by cold rolling. During fabrication the alloy was given intermediate anneals at 845OC followed by quenching. The specimens after preparation were solution treated at 1000°C (y field) or 845°C (a field) for 1 to 2 and 5 to 6 hr, respectively, in a dynamic vacuum of about 2 x lom6 torr. The tensile and modulus specimens were drop-quenched into iced brine through an aluminum foil which vacuum-sealed the bottom of the furnace tube. The MOssbauer foils were drop-quenched into helium gas cooled by passing through N2 (liq) in a copper coil. The grain diameter of the modulus and tensile specimens was between 0.025 and 0.035 mm. The samples were aged from 400" to 500°C in a dynamic vacuum of 2 x 10-6 torr and cooled by pulling into a water-cooled portion of the vacuum system. The dynamic Young's modulus was measured at room temperature using electrostatic excitation and detection of longitudinal vibrations.' Neglecting any length change during the aging, (this is expected to be comparatively small), the fractional change of Young's modulus (?Et)/Eav, is equal to twice the fractional change of the resonant frequency (?ft)/fav . ?ft =ft —fo where fo and ft are the resonant frequencies of a specimen before aging and after aging to time t. The measured f's, approximately 51,000 cps, were corrected to 25°C for any variation in the ambient temperature. The tensile tests reported were carried out at room temperature in an Instron with a 1000 lb full scale load cell. The flow stress reported herein corresponds to a strain of 0.002. The Massbauer spectra were taken in a constant acceleration model AM-1 NSEC spectrometer. The

Jan 1, 1970

By W. D. Smith

It has been 5 years since the writer left the Philippine Islands and while in that country his chief work did not lie in this field, though he has visited all but one of the localities mentioned in this article. The principal field studies relating to oil were M de by his colleague, Mr. Wallace E. Pratt. The writer's investigations ealt with the general stratigraphy and paleontology of the Philippines. with the exception of the investigations made by Mr. Pratt and the writer very little information on this subject is available. A number of geologists in the employ of large oil companies have visited the Islands from time to time but, following the general rule, the public has scarcely ever been permitted to learn anything of the results. The writer is indebted to the Bureau of Insular Affairs, Washington, for late information regarding recent legislation in the Islands relating to petroleum. All the known oil seeps, petroleum residues, such as ozocerite, and natural-gas emanations are associated with Tertiary sediments. The chief seeps and most promising prospects are located as follows: 1. Bondoc Peninsula (lower end), Tayabas Province, Southeast Luzon. 2. The west coast of the island of Cebü from Alegria north to, and perhaps beyond, Toledo. 3. Central Mindanao not far from Lake Lanao. 4. The ozocerite veins on the Island of Leyte in the northwestern part in the vicinity of the town of Villaba. 5. Natural gas from some deep wells in Tertiary shale formations on the eastern flank of the Cordillera and extending out under the plain on the island of Panay. The first mention in geological literature, to the writer's knowledge, of gas or petroleum in the Philippines is found in the description of the Island of Panay by the Spanish geologist, Abella, in the year 1890. In 1898, an oil well was being dug on the estate of Smith Bell & Co., an English concern, near the town of Toledo on the west coast of Cebu. In

Jan 1, 1921

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is necessary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important components of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transformation are dealt with in a highly detailed and descriptive manner in the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilibrium conditions of thermal treatment. The Guillet1 diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts. At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. [ ] Reference may be made at this point to the efforts of Marshy to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encoun-

Jan 1, 1942

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors' k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system' is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.' The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953

THE papers by G. F. Loughlin and I. A. Ettlinger discussed the distribution of formations and ore-bodies in two of the main mining districts of the Southwest. The convergence of the deeper orebodies at Cripple Creek points to their common hypogene ori-gin, as do the occurrences of the copper ores of, central Arizona. E. L. Bruce described the areas in southwestern On-tario around Red Lake and Woman Lake, another prom-ising gold district. Of special interest was a series of lantern slides showing the use of power-driven boats and of hydroplanes as means of transportation. Within a few years, no doubt; such devices will revolutionize the mining industry and reconnaissance mapping in these relatively inaccessible areas. Much interest was evinced in the paper by J. W. Finch on "Sedimentary Metalliferous Deposits of the Red Beds." It was written as a caution to people at-tempting to mine these deposits. The discussion of the chemical equations presented in the paper brought out the fact that a large amount of study of such ores is necessary before we shall be able to write equations to explain their formation. Especially pertinent were the discussions by David White as to the relation of decay-ing plant tissue to metalliferous deposits and the color of sediments; also the point brought out by T. S. Lover-ing that chemical compounds produced by bacteria may greatly affect the deposition and reorganization of sedi-mentary metalliferous deposits.

Jan 3, 1928

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952

By Milo Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland Portland Cement Co. are located at Metaline Falls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in &apos;the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. I is a view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by S ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond wits used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By V. H. Gottschalk

THE solubility of gases in metals has been of interest since Graham&apos;s time in 1866, but, although the subject was actively studied by iron and steel metallurgists during the eighties, the era of painstaking laboratory investigation begins in 1907 with the publication of Sieverts&apos;1 thesis on the occlusion and diffusion of gases in metals. Since then, Sieverts has worked almost continuously in this field, and his views on the subject are the prevailing ones at the present time.2 Probably the most important result obtained by Sieverts, and frequently verified since by other observers, is the discovery that at a constant temperature the solubility of almost all gases in both the liquid and solid state of most of the metals is proportional to the square root of the pressure (for pressure above 100 mm.). The obvious explanation of this fact is that the gas dissolves as atoms and not as molecules, although it has been pointed out a number of times, first by Donnan and Shawl in connection with their work on the solubility of oxygen in silver at 1075° C., that the formation and solution of a compound of the metal and gas would also be indicated by a variation of the solubility with the square or higher root of the pressure. Sieverts4 himself raised the question whether the usual explanation (i. e., that the gas dissolves as atoms) may not be wrong, when he found that the square root law held also for the solubility of sulfur dioxide in molten copper; in which case dissociation into simpler molecules or atoms does not take place. Stubbs5 subsequently showed that Sieverts and Krumbhaar&apos;s "constant" for sulfur

Jan 1, 1932

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.* May, &apos;71.. 1 3 2. Bethlehem. Pa Aug., &apos;71.. 1 10 8. Troy, N. Y Nov., &apos;71.. 1 1S 4. Philadelphia, PaFeb., &apos;72.. 117 5. New York, N. Y.*May: &apos;78.. 120 5. Pittsburgh, PaOct., &apos;72.. 125 7. Boston, MassFeb., &apos;78.. 128 8. Philadelphia, Pa.* May, &apos;78.. 2 3 9. Easton, POct., &apos;78.. 27 10. New York. N. YFeb.. &apos;74.. 2 11]

Jan 1, 1946