Search Documents

Jan 6, 1951

Jan 7, 1976

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By R. V. Norris

In a former paper on this subject,' I summarized Murgue's theory and experiments, and presented a large number of tests of mine-fans, stating some conclusions, " more or less warranted by the evidence," as to design, capacity and efficiency. Since that time the very valuable report of Mr. M. Walton Brown: Committee on Mechanical Ventikators, Institution of Mining Engineers, has appeared, and I have made additional experiments which tend to clear up some points in connection with this subject. Design and Tests of the Luke-Fidlbr Colliery Fan. The Luke-Fidler fan (see Figs. 1, 2 and 3), built to replace an old wooden fan at a very fiery colliery, presents some pecu-

Jan 1, 1905

Jan 3, 1976

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By Frederic Brunton

I. INTRODUCTION THE smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at' very high efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of $1.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 tons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by Alfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Works, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913).

Jan 7, 1915

I would like to congratulate the authors on an interesting paper and, in particular, on their justification of the use of superposition in treating gas wells. They state, however, that no theory has previously been developed lor treating the variable rate drawdown case. In a paper published a few years ago by my colleagues and myself, a method is described which allows a constant rate drawdown curve to be derived for any well. regardless of real rate variations. This method has the great advantage that it is not necessary to make any assumptions regarding the form or uniformity of the reservoir, and the derivation suggested by the present authors is simply an idealized case of our more general treatment. In the light of several years' experience in the derivation of constant rate drawdown curves: I would like to point out that the method proposed by Odeh and Jones may lead to confusing answers, particularly if applied over an appreciable time interval. The reason is that, if pressures are measured when a well is flowing, non-linearities in plots like Figs. 1 and 2 can arise due to either (1) changes in the skin factor with time and/or flow rate, or (2) an inhomogeneous reservoir. Separation of these two effects is only possible if some of the pressures used in the analysis are measured when the well flow rate is 0 or, in other words. during brief shut-in periods. REFERENCES 1. Arthur, K. B.. Metunomski, Z. G. and Ruche, Ms "Intetet ct methode d'utilisa tion des mesures de pression [)our Petude des gisemonts" Revue de T'I.F.P. (Nov., 1962) XVII, 1299. 2. Thomere, R. and Arthur, K. R.: "Analysis of the Pressure Bet~avior of a Production Well Subject to Interterence and Its Application to Reservoir Models", Paper SPE 1189 presented at SPE :Amund Fall Mecting Ireld in Denwer, Colo. (Oct. 3-6, 1965).

Jan 1, 1966

By Archiblad MacMartin

The Kunigin-Marien-Hiitte is the only works in Germany where the Bessemer process is carried on by the direct method. The Besserner plant there, is arranged after the true English type, and the only resemblance to the Swedish mode of 'procedure is the dispensing with the use of spiegeleisen at the end of the "blow." In a new department of the establishment, started within three years, each of the converters is turned by means of a very neat and compact reversible engine, the steel shaft of which is an endless screw, which turns against the oblique cogs of a large wheel attached to the shaft of the vessel. An advantage which this arrangement possesses over the ordinary English hydraulic arrangement, is the fact that the endless screw suffices to turn the vessel, in either direction, any number of complete revolutions; while even the latest American improvements, so clearly explained to us by Mr. Holley at the opening session of this meeting, do not secure even one complete revolution without changing the angle of inclination of the hydraulic piston. In the endless screw arrangement, there being no limit to the working of the motor in either direction (no return-stroke necessary), the vessel can always, unless outside reasons demand the contrary, be turned around to any desired position by the shortest cut, whether backwards or forwards. Also, the diameter of the cogwheel attached to the vessel can be made sufficiently great to avoid all unevenness of motion. In the old department the motive-power still continues to be hydraulic. If reports be true, the new department produces spiegelized steel, for the manufacture of all-steel rails. But the old department is still, as from the beginning, devoted to the production by the direct method of steel for steel-headed rails. The most remarkable fact connected with this direct steel is the ease with which it welds to the iron 'of the rail-packets, although no borax or other fluxing agent is used to facilitate the welding. It is very rarely that an exception occurs, and an ingot or a charge is discarded by the rail-mill. The mixture of pig-iron used for the production of this steel is melted in cupolas of very interesting construction (not to be de-

By Messervey, J. P.

NOVA SCOTIA is sharing in the rapid advance of the mining industry that is one of the remark- able features of Canada's recent progress. The production of coal and gypsum has increased rapidly, and there has also been a marked development in the mining of gold, salt, zinc, copper and other minerals. Coal, the basis of the principal mining industry in the Province, was discovered by the early explorers on the shore of Cape Breton Island, and used by the garrison at Halifax as early as 1749. The first government record shows total annual sales amounting to 1668 long tons in the year 1785, while last year production was 6,643,000 long tons. The principal mines are discussed in a separate paper by Alexander L. Hay1.

Jan 1, 1928

By J. D. Cooner

SINCE my working life of 32 yr has been spent in and about the anthracite mines of the Hudson Coal Co., and the previous 4 yr in a college school of mines, I can write best about the safety program of a coal mining company. However, most of the suggestions, statements and practices mentioned herein are applicable to the members of a safety organization and program of almost any industry. It is realized that industrial officials actually interested in real safety work are fully acquainted with the requirements of a practical safety program. Therefore, for such persons there may be nothing new in this paper. The Hudson Coal Co. of Scranton, Pa., employs 7,000 men and produces 5,000,000 tons of anthracite annually at nine collieries scattered for a distance of 40 miles throughout the Lackawanna and Wyoming valleys of northeastern Pennsylvania. For the past 17 yr of the above mentioned 32, I have been engaged in safety work as a safety inspector, assistant mine superintendent, and at present the safety engineer. I have also had the privilege of visiting coal and metal mines in other parts of the United States and Canada. We Americans are the most careless people in the world. If any one doubts this statement why are 100,000 of our people killed accidentally annually? Or why during the almost four years we were engaged in World War II were more of our people killed accidentally at home than were killed in our army, navy, marine corps, coast guard, and other services during the same period? We are careless everywhere in our homes, on the highway, at work and at play. The purpose of this paper is to outline the requisites of a safety department and its program to stop the accidents occurring to employees at work in mines or industrial plants. The first requisite for a safety program is that the management must be convinced of the need and value of a real safety program. By "management" is meant each department head from the president down. Otherwise a good safety department with a good safety program will not succeed because it will not have the proper personnel and equipment to work with, its rules and regulations will not be enforced, and the members of the safety department will be belittled in the eyes of most of the workmen and supervisors. Next, a safety engineer and his inspectors should have worked in the production end of the mines as workmen and also in an official capacity. They are then in a position to have practical and first hand knowledge of the accident hazards of the industry, how to prevent them, and in general the problems of both the workmen and officials. Some men are appointed as safety inspectors when they are physically unable to carry on as mine officials. Such men may know the safety end of the industry and even be safety-conscious, but if they are physically unable to be mine officials they are also physically unable to be safety inspectors, as a safety inspector in our mines must walk from 2 to 4 miles on each daily inspection-and visit each working

Jan 1, 1948

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By J. P. Kerr, W. H. Cordell

Conditions in the oil and gas industry in Indiana were about the same in 1935 as in 1934. This is especially true of the old Trenton area and the Harrison County area where production was steady and almost no exploration and development took place. The past year has seen an increase in drilling activity and a decrease in oil and gas output in southwestern Indiana. In the state, 224 wells were completed in 1935, of which 48 were oil wells, 61 gas wells, and 115 dry holes. A few of these were old gas wells deepened to oil horizons. Twenty-six wells started during 1935 were not completed by Dec. 31. Approximately one-half the wells drilled were within proven areas. A relatively large number of wildcats, especially in Daviess, Pike and Gibson Counties, were in search of new gas supplies to supplant the diminishing resources in those counties. The decreased production of gas was due largely to the fact that existing supplies declined more rapidly than new fields could be brought on. The Alford field, in Pike County, which produced the bulk of the supply in 1934, was called on to do likewise in 1935, but was unable to respond sufficiently to keep up the yearly production for southwestern Indiana. During the last half of the year, the Oaktown field, Knox County, was connected with one of the principal pipe lines of the state, which helped to keep gas production above an unusual low. The decline in oil production was due almost entirely to proration during the first eight months of the year. The proration affected Daviess, Pike, Gibson, Sullivan and Vigo counties, which produce about three-fourths of the total for the state. After proration was lifted, the wells never quite reached the conditions existing before proration. The average daily production per well in Indiana is less than two barrels. The outstanding development in Indiana in 1935 was the drilling in the Oaktown field immediately before and after the laying of the 6-in. pipe line to the field. Almost without exception the wells came in with an open flow of two to four million cubic feet. At the end of the year, 26 wells were connected to the pipe line. Development of this field will

Jan 1, 1936

By J. P. Kerr, W. H. Cordell

Conditions in the oil and gas industry in Indiana were about the same in 1935 as in 1934. This is especially true of the old Trenton area and the Harrison County area where production was steady and almost no exploration and development took place. The past year has seen an increase in drilling activity and a decrease in oil and gas output in southwestern Indiana. In the state, 224 wells were completed in 1935, of which 48 were oil wells, 61 gas wells, and 115 dry holes. A few of these were old gas wells deepened to oil horizons. Twenty-six wells started during 1935 were not completed by Dec. 31. Approximately one-half the wells drilled were within proven areas. A relatively large number of wildcats, especially in Daviess, Pike and Gibson Counties, were in search of new gas supplies to supplant the diminishing resources in those counties. The decreased production of gas was due largely to the fact that existing supplies declined more rapidly than new fields could be brought on. The Alford field, in Pike County, which produced the bulk of the supply in 1934, was called on to do likewise in 1935, but was unable to respond sufficiently to keep up the yearly production for southwestern Indiana. During the last half of the year, the Oaktown field, Knox County, was connected with one of the principal pipe lines of the state, which helped to keep gas production above an unusual low. The decline in oil production was due almost entirely to proration during the first eight months of the year. The proration affected Daviess, Pike, Gibson, Sullivan and Vigo counties, which produce about three-fourths of the total for the state. After proration was lifted, the wells never quite reached the conditions existing before proration. The average daily production per well in Indiana is less than two barrels. The outstanding development in Indiana in 1935 was the drilling in the Oaktown field immediately before and after the laying of the 6-in. pipe line to the field. Almost without exception the wells came in with an open flow of two to four million cubic feet. At the end of the year, 26 wells were connected to the pipe line. Development of this field will

Jan 1, 1936

By Courtenay de Kalb

REVISION of the United States mining law is needed. chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. LAW OF THE APEX The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from masses which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future. development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes

Jan 2, 1915

By John Skelton, E. J. Harvey

Seepage runs (stream flow measurements in a short time at many points in a basin,) and stream flow records are used to locate losing areas in stream basins in the Missouri Ozarks. The terrane consists of dolomitic limestone and sandstone of Ordovician and Cambrian age. Side-looking radar imagery emphasizes variations in topography and reveals two types of drainage basin topography, rough and smooth (deeply dissected and slightly dissected basins). In the deeply dissected basins (rough ones), main streams and tributaries generally gain. In the slightly dissected basins (smooth ones), the streams lose a part or all of their flow. Logan Creek, a tributary of Black River in the southeastern Ozarks, loses much of its storm runoff and all of its dry weather flow. East and West Forks of the Black River, north of Logan Creek, gain water through most of their main stems. On radar imagery Logan Creek basin has a light uniform tone and smooth texture in contrast to the darker tone and rough texture of the East and West Forks. The contrast is due to the difference in degree of dissection. Therefore, radar imagery may be useful in suggesting gaining or losing streams (or reaches of streams).

Jan 1, 1973

By H. J. Levinstein, H. J. Guggenheim, C. D. Capio

An optical incestigation of the phase transformations in RbFeF, has been conducted. Details of the ferromagwetic phase transition and the metamagnetic state are disczrssed. The three-dimensional magnetic domain structure existing in bulk crystals of RbFeF3 is described, as well as the effect of the magnitude and direction of the applied magnetic field on the domain struclure. The strong magnetoelastic interaction in RbFeF, is demonstrated. The results of the direct observation of the role of dislocation subboundaries and slip bands as nucleation sites and as pinning sites for magnetic domain walls are reported. THE perovskite compound RbFeF, has recently been shown to exhibit three magnetic states.''' Above 102°K it is paramagnetic, between 102" and 87°K it is antiferromagnetic. and below 87°K it is ferromagnetic (i.e., exhibiting remanence) with a modification of the magnetization occurring at 40°K. The changes in magnetic structure at 102o, 87°. and 40°K are accompanied by shear transformations to successively lower crystal symmetry classes.3 At 102°K a second-order phase transformation to a tetragonal crystal structure occurs. The c/o ratio increases with decreasing temperature to a value of 1.0034 at 87°K where the crystal undergoes another shear transformation to an ortho-rhombic crystal structure. The magnetic modification at 40 K is also accompanied by a shear transformation to a lower crystal symmetry. RbFeF3 is unique in that in the ferromagnetic state it is transparent in the bulk to visible light, has a low saturation magnetization, a large magnetic rotation. and has good optical properties.' All these features make it an ideal material for the investigation of magnetic domain structures in bulk crystals. In addition a dislocation etch has been developed which reveals the point of emergence of dislocations with the (100) surfaces of RbFeF3,5 making it possible to determine the dislocation arrays in the material. As a result domain wall dislocation interactions can be observed in the bulk crystal. In this paper we report on 1) the crystallography of the phase transformations in RbFeF3. 2) the domain configurations as a function of magnetic field and crystal orientation. 3) the interaction of dislocations and magnetic domain walls in RbFeF,. EXPERIMENTAL PROCEDURE Since the temperature range of interest is below room temperature the dewar shown in Fig. 1 was employed. It was designed to fit on the stage of a Leitz panphot metallograph, and permitted examination of the sample at a magnification up to 150 times. The dewar consists of a double-walled glass cylinder bent into an L shape. The space between the walls is evacuated. The viewing wirldows were made of four optically flat quartz discs aligned parallel to each other and sealed to the sides of the concentric cylinders. The specimens were mounted in a holder attached to a flexible plastic shaft. Various holder designs were employed depending upon the type of observations to be made. For studies of the phase transformation between the antiferromagnetic and ferromagnetic state the holder shown in Fig. 2(d) was employed. This holder permitted accurate temperature control at 82" to 88°K by balancing the heat input from the carbon resistance heater against the heat loss to a heat sink immersed in liquid N2. Magnetic field studies were conducted by employing the holders shown in Figs. 2(a) and (b). The holder shown in Fig. 2(n) has a solenoid imbedded in it. such that the magnetic field direction is in the same direction as the incident light. The magnetic field provided by the holder in Fig. 2(b) is perpendicular to the incident light direction. The holder in Fig. 2(r) was employed when observations of the specimen were desired while an elastic bending stress was applied to the sample. The stress was applied to the sample by pulling a wire from outside of the dewar. The wire was attached to a lever pivoted on the holder. which caused the knife edge of the lever to push against the sample. The crystal growth and the sample preparation were described previously.' PHASE TRANSFORMATIONS The first phase transformation in this system is from the cubic perovskite structure to n tetragonal

Jan 1, 1970