Search Documents

By S. J. Matas, R. F. Hehemann, R. H. Goodenow

The hot-stage metallographic method has been employed to determine radial growth rates of upper and lower bainite. Lower bainite appears to grow as individual plates that increase in both length and thickness while upper bainite grows as sheaves of closely spaced plates or needles. A discontinuity in the temperature dependence of the growth rate appears to be associated with the transition from upper to lower bainite and stepped quenching experiments suggest that lower bainite will not continue to grow when the temperature is raised to the upper range. Thus, a single process does not appear to control the growth of both upper and lower bainite. A tentative model based on the forces acting on a dislocation interface is proposed to account for the slow growth of bainite. It has been recognized since the early studies of Davenport and Bain that a close relationship exists between the martensite and bainite transformations in steels. However, diffusion of carbon during the transformation has lead to considerable controversy concerning the reaction mechanism.1-7 Many studies4,5,7-9 have emphasized the structura and kinetic aspects of the bainite reaction and, in particular, the difference observed between the two forms of bainite—frequently termed upper and lower bainite. A kinetic difference between the two types of bainite has been revealed in the activation energy determined from the overall reaction;4,5 however, many difficulties arise in an interpretation of these activation energies since a number of temperature dependent factors contribute to the kinetics of the overall reaction. The displacive surface relief10 accompanying the bainite reaction permits a separation of the nuclea-tion and growth contributions to the reaction and allows the kinetics of the growth process to be examined. Several investigations of this type have been conducted; however, they have been restricted to the low temperature range.3'6'11 Here, bainite plates are observed to grow slowly in both length and width. The present investigation extends such studies to include the upper bainite range. MATERIALS AND PROCEDURE Materials. The composition of the steels studied in this investigation are presented in Table I. The range of composition permitted a study of the effect of carbon content on the growth rate of upper bainite in the 9 pct Ni steels and consideration of both upper and lower bainite in the higher carbon steels. These steels were received as hot-rolled rounds and were forged to approximately 1/2 in. thick plates for preparation of metallographic specimens. In order to produce an essentially zero carbon steel, Steel A was decarburized in wet hydrogen at 1550°F for 15 days with the result tabulated as Steel AD. Experimental Procedure. In order to study the slow growth of the displacive transformation product, a commercially available Leitz hot stage was modified to permit heating of the specimen by its own resistance in a manner similar to that employed by other investigators.6 The furnace chamber was maintained at a pressure of 2 to 3 X 10-5 mm Hg prior to austenitizing at 2000° ± 12° F for 5 min. Samples could be cooled from the austenitizing to the transformation temperature in approximately 15 sec and the progress of transformation was recorded with a 9 cm by 12 cm single frame camera or a 16 mm movie camera. RESULTS AND DISCUSSION Growth Characteristics. The general growth characteristics observed in this investigation were analogous to those reported previously.3,6,11 Typical growth sequences for the high temperature and low temperature forms are illustrated in Figs. 1 to 5. In both temperature ranges, bainite plates increase in length at slow, temperature dependent rates until interrupted by a grain boundary, another plate, or

Jan 1, 1963

By DR. RICHARD RATHBUN

ON behalf of the Regents and the Secretary of the Smithsonian Institution, it gives me great pleasure to welcome you to the National Museum; but it is to your own museum, since it belongs to you in common with all the people of the country. Still young in a life which has been beset with many difficulties, it has gathered strength and attained a growth quite unprecedented. In fact, it is this very growth which has been the chief cause of trouble, always leading far and away beyond the capacity for storage ; and to-day there is nearly as much material contained in outside buildings as is displayed in this one. You will, accordingly, find the collections crowded, the cases so close together that their contents are often difficult to view, and the arrangement generally lacking symmetry. You may, therefore, be inclined to regard us as poor custodians of the collections of a great nation, but I beg you to withhold your judgment for a while. From the beginning there has been abundant zeal and activity and a proper direction of affairs, but space and money have been lacking. There is now a prospect of better times. All about you here is a beautiful park, but without. a covering it is not adapted to museum purposes. Upon it, however, a new large building is going up, so extensive in its dimensions that technology can soon be given a fitting home, thus realizing one of the earliest aspirations of the Regents. Some sixty-five years ago the extensive returns of specimens from the famous Wilkes Exploring Expedition around the world began to reach Washington, where they were deposited in the Patent Office Building, and formed practically the first of the National Collections. Six years later the Smithsonian Institution, based upon the bequest of James Smithson, was

Jul 1, 1905

By Leonard Waldo

The recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high as that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, text-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful. For mental calculation the easiest rule to convert centigrade into Fahrenheit is to add 32° to twice the centigrade reading less one-tenth of this product: Thus 1000' C. = 2000" — 200" + 32" = 1832" F., and to convert Fahrenheit to centigrade, subtract 32" from the Fahrenheit reading, multiply by 10 and divide by 2 and 9 successively : Thus 1000° F. = 1000° — 32° = 968° X 10 = 9680° - 2 = 4840° - 9 = 537.77° C. Another and often very convenient method is by 'use of a graphic construction as follows :

Jan 1, 1913

The St. Lawrence Seaway and power project has received the support of the Canadian Parliament, with the House of Commons approving a bill that authorizes the Government to proceed with construction of the seaway, with or without U. S. cooperation. Itogan Mining Co., third largest gold mine in the Philippines, reopened in December under the management of Marsman and. Co. The 'mine was almost totally destroyed during the occupation. The International Materials Conference committee on copper, lead, and zinc has recommended against stockpiling during the: first quarter of 1952 because of the current demands for defense needs. The General Services Administration has told producers who have contracts calling for delivery of copper to the stockpile during the first quarter of 1952 that they do not need to make those deliveries.

Jan 1, 1952

By Leason Adams

THE thermocouple as a device for the measurement of temperature is rivaled only by the platinum-resistance thermometer. Both instruments are capable of the highest precision, but the thermocouple, on account of its cheapness, ease of construction, and small cross-section, is finding a continually widening field of usefulness for industrial control as well as for laboratory measurements. Formerly, the thermocouple was subject to two disadvantages: errors due to lack of homogeneity of the metal and the labor involved in the interpolation between fixed points on the temperature scale. Former publications from the Geo-physical Laboratory have described the methods' for the selection and testing of thermocouple wire and have presented standard calibration curves2 for platinum-platinrhodiun and copper-constantan couples, so that the most important objections to the thermocouple as a precision thermometer have been removed. The calibration tables published in 1914 covered the range 0-1755° for the platinum-platinrhodium couple and 0-350° for copper-constantan. It has seemed desirable to extend the table for copper-constantan to -200 and also to include a table for the Hoskins thermocouple. Accordingly, in this paper, the new tables are presented, together with a brief explanation of their use; and, finally, certain diagrams and a paragraph on "cold-junction corrections" are given. Standard Calibration Tables.-In Fig. 1, which illustrates how the electromotive force (e.m.f.) of each of the three couples varies with the temperature, the temperatures of one junction are plotted as abscissas and the corresponding thermo-e.m.f.'s as ordinates. The second junction of the couple is supposed to be at 0°; the curves, therefore, pass through

Jan 9, 1919

By C. W. Jr. Gennet

ANNOUNCEMENT was made in the spring of 1926 that the Boston & Maine R. R. Co. had contracted with the well known German steelmakers, Messrs. Fried Krupp, for the manufacture of 15,000 tons of basic open-hearth steel rails at the Rheinhausen Works, for delivery to Boston, Mass. The manufacture of rails in the United States has for many years been almost a national pride, and as this feeling is chiefly the result of a long-time liberal and consistent patronage of, American rails by American railroads, it is not strange that this somewhat unusual announcement should arouse more than ordinary interest. Since the end of the World War, the importation of foreign rail has been fairly large, principally because the newly created economic conditions have rendered some American competition more difficult, but the tonnage imported, for the most part, has been made up of small orders for miscellaneous use; and the contract referred to constitutes the largest single importation of foreign rail in over ten years. In 1915, the Algoma Steel Co. of Sault Ste. Marie, Canada; supplied the Illinois Central R. R. with 30,000 tons of rails,1 and various other American roads with smaller amounts. In 1902, 1903 and 1904, large tonnages of rail from abroad were purchased, the Louisville & Nashville R. R. alone obtaining 30;000 tons from German mills. It is the object of this paper, to present, in what is believed to be a new and concise form, figures showing the production and consumption of rails in the United States, and to record some of the testing and inspection results of the recent Krupp rails; also, to direct attention to two quite unique departures from American practice that were regular features of the Krupp process and which are worthy, it is thought, of careful study.

Jan 1, 1928

Minnesota School of Mines Experiment Station, University of Minnesota, Minneapolis, Minn For copies of Bulletins or a list of publications, address The Director Bulletins available are Bulletin 1, Iron mining in Minnesota, by C. E Van Barneveld (1912), $1, 2, Concentration tests on Mesabi ores, by W R Appleby and E Newton (1913), 3, Preliminary concentration tests on Cuyuna ores, by W. R Appleby and E Newton (1915), 4, Bibliography of Minnesota mining and geology, by W. Gregory (1915); 5, Manganiferous iron ores of the Cuyuna district, by E Newton (1918), 7, The future of the Lake Superior district as iron-ore producer, by E W. Davis (1920), 9, Magnetic concentra¬tion of iron ore, by E. W Davis (1921); 10, Ball mill crushing iii closed circuit with screens, by E W Davis (1925); 12, Minnesota manganiferous iron ore in relation to the iron and steel industry, by T L Joseph and S P Kinney (1927). A mining directory of Minnesota, by J J Craig, is published annually.

Jan 1, 1933

By C. R. Austin

In a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreasing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test have also shown promise as providing a "merit index" of high-temperature serviceability.= Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350" C. (and a maximum of 450" C. for alloy steels) to serve as a suitable basis for comparison evaluations of materials and for judging permissible stresses. Koerber and Pomp consider, however, that above these temperatures creep limit must be substituted for the high-temperature yield point as the all-important characteristic of the material. Whatever may be their definition of

Jan 1, 1934

By W. P. Blake

THIS furnace is designed especially for the oxidation of sulphur or arsenic in pyritic ores, but may be used for all oxidizing or desulphurizing operations, and for calcining, roasting and chloridizing ores, or for drying ores in large quantities preparatory to treatment by magnetic separators or otherwise. It is of the tabular, revolving type, with automatic feed and delivery, and is a modification of the Cornish calcining furnace, designed by Brunton, from which it differs, however, not only in construction, but in two or more radical features, for which novelty is claimed and patents have been applied for. The principal of these novelties are: 1. A series of concentric terraced floors, one above another. 2. The introduction of superheated air upon the charge without contact with the fuel. In the furnace which I have had in operation for more than a

Jan 1, 1893

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

IN spite of considerable study,1-5 the nature of slime coatings in flotation is still not completely understood. However, phenomena that control flocculation and dispersion of colloidal systems are now interpreted in terms of electrical double layers."' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed, flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which electrokinetic data are available.8-12 Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple.

Jan 7, 1958

By H. M. Morse

This report on oil and gas development in Mississippi covers the period from Jan. I, 1944, to Dec. 31, 1944: Salt Domes During the year six salt domes were drilled for sulphur, but no commercial sulphur deposits were found. One salt dome, the Bruinsburg, in Claiborne County, has produced gas- at 935 to 940 ft' in Moody's Branch marl. The Stringer salt dome in Smith County and the Ruth salt dome in Lincoln County both had a slight showing of heavy oil. Other salt domes have been dry. In addition to the Bruinsburg dome, the Allen salt dome, in Copiah County, and the Richton salt dome, in Perry County, were discovered in 1944; also the Sumrall dome, in Covington County. New Oil Fields Baxtemille Oil Field.—The Baxterville oil field was discoveredby the Gulf Refining Co, in sec. 7, T. I N., R. 16 W., Lamar County. At the end of the year this field had one oil well, with two active operations. Production for 1944 was 1047 bbl. of oil. GwinvilLe Field.—Gwinville field was discovered by S. W. Richardson, in sec. 24, T. 9 N., R. 19 W., Jefferson Davis County. This discovery well was a gas-distillate well, the oil being crystal clear. At the end of 1944 there were two gas wells and one oil well in the field. The oil well is approximately 2 1/2-miles from the gas- distillate wells. Gas production was 55,801 M cu. ft. and the distillate production was 2644 barrels. Heidelberg Oil Field.— The Gulf Refining Co. discovered the Heidelberg field in sec. 30, T. I N., R. 13 E., Jasper County, in January 1944. This field has by far exceeded the other 1943 and 1944 discoveries, having approximately 56 oil wells, 7 dry holes, and 10 active wells at the end of the year. Production to Jan. I, 1945 was 1,441,192 bbl. of oil. Mallalieu Oil Field.—The california Company discovered the Mallalieu oil field in set. 10, T. 7 N., R. 8 E,, Licoln. County. At the end of the year there was one well in the field with three active operations. Production was 32,303 bbl. of oil. Old Oil Fields Brookhaven Oil Field, in Lincoln County, has one oil well, which produced 2590 bbl. of oil during 1944. CarY Oil Field, Sharkey County1 has only one producing well, which produced 11,818 bbl- of oil during the Year- In Cranfield Oil Field, dams County, II oil wells and two gas-distillate wells were drilled in 1944 and there were five active wells on Dee. 31, 1944- The total production for the Year was 5251422 bbl-of oil. The gravity of the oil is 40" to 54.9'- In Eucutta Oil Field1 Wayne County1 34 oil wells were completed during 1944. There were five dry holes and six active wells at the end of the year.. The field produced 454,332 bbl. of all d the average gravity is 25" Flora Oil Field, Madison County, pro-

Jan 1, 1945

DURING the early part of August, 1880, I was directed by Prof: J. P. Lesley, State Geologist, to assume charge of the geology and mapping of the Second Geological Survey of the anthracite coal-fields. I visited the region unineumbered by any instructions other than this, that I should submit a plan for making the sur- * In the practical application of this method I wish to acknowledge the valu¬able aid rendered by my assistant, Mr. A. W. Sheafer.

Jan 1, 1881

By P. S. Katval

It is interesting to note that an attempt has been made to rationalize the effect of prestrain on the strength of Hastelloy X-280 after various aging treatments. However, two points raised by the authors seem to be somewhat unclear. 1) Concerning their Fig. l(a), the authors state: "Extensive dislocation networks are still in evidence. The 24-hr aging at 1500°F and the 15-min soak at 1350°F did not eliminate the dislocations introduced by the 20 pct cold reduction." This is, of course, to be expected since complete "elimination" of dislocations would require recrystallization which does not occur at 1500°F in Hastelloy X. However, recovery

Jan 1, 1969

By David E. Jones, Dean K. Hunt, C. Y. Chen

INTRODUCTION Of all the numerous geological hazards that threaten the well-being of urban areas in the United States, probably none is so widespread, persistent, and diversified as surface subsidence (HRB-Singer, Inc., 1977). Simply defined, subsidence is the vertical displacement or sinking of the ground surface caused by either natural phenomena or man's activities. The downward movement, however, can be accompanied by horizontal movement, strain, tilt and even by a locally upward movement. Damage to structures and the environment can result from any of these movements. Extracting subsurface materials, fluids and solids, accounts for most man-induced subsidence in the United States. Among all the mining-related subsidences, the collapse of voids created by underground coal mining has been the major cause in inflicting surface damage (Comptroller General of the United States, 1979). Subsidence from coal mining may occur within a few weeks or be delayed for years, depending upon the mineral layer's depth below the surface, the overlying rock strata's characteristics, the extent and methods of mining that were employed, and the time deterioration of pillar and mine structure. Unless underground resources are not mined or control measures are implemented to prevent or minimize damage, some degree of surface subsidence and its accompanied deleterious effects are often inevitable. The ways to control the subsidence and minimize surface damage may include: 1. Precautionary measures built into new structures or surface features. 2. Preventive works applied to existing structures or surface features. 3. Mine design incorporating special underground layouts. 4. Any combination of the above measures. Upon the enactment of Public Law 95-87, the Secretary of the Interior, through the recently created Office of Surface Mining (OSM), was authorized to promulgate rules to regulate mining reclamation including subsidence control. Proposed on September 18, 1978, these rules were finalized, following public comment and hearings, on March 13, 1979, as part of the permanent regulatory program for the regulation of surface mining and reclamation operations which include the surface effects of underground mining. On January 28, 1981, Secretary Watt of the Department of the Interior issued an order to re- quire all agencies to identify with recommendations all regulations which are believed to be excessive, burdensome or counterproductive. Also on February 17, 1981. President Reagan issued Executive Order No. 12291 requiring all Federal agencies to conduct a regulatory review to make a determination that each promulgation of a regulation is clearly within the authority delegated by law and consistent with Congressional intent (Federal Register, 1981). As a result, OSM initiated the regulatory reform to revise the permanent regulatory program. Following a brief discussion of the technical aspects and the effects of subsidence on man and his environment, this paper presents a historical overview of how rules and regulations are used to govern the subsidence related problems. The development of the regulation of subsidence under Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act) are also discussed, including the new regulations being developed under the regulatory reform program. SOME TECHNICAL ASPECTS Am EFFECTS OF FINE SUBSIDENCE An extensive historical review of mining subsidence is given by Zwartendyk (1971) and Shadbolt (1978). Comprehensive technical presentations have been given by Henry (1956), King and Whetton (1957), Hall and Orchard (1963). Muller, et al. (1968). Grard (1969), Voight and Pariseau (1970). Kapp and Williams (1972), Cummins and Given (1973), Brauner (1973) , and NCB (1975). A theory of surface subsidence due to underground mining was perhaps first fundamentally stated by a French engineer, Toillez, in 1838, and formulated by a Belgian engineer, Gonot, in 1839 (Goldreich, 1913, cited by Zwartendyk, 1971). Since that time,

Jan 1, 1982

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

The Nominating Committee for Institute Officers in 1953, John R. Suman, chairman, completed its work at the Annual Meeting in February, and has made its report to the Board of Directors. The President-Elect in 1953 serves as President in 1954. The ticket follows: For President-Elect and Director, Leo F. Reinartz; for Vice-President and Director, A. B. Kinzel and Lloyd E. Elkins; for Director, Hjalmar W. Johnson, Philip Kraft, Gail Moulton, Edwin L. Oliver, Philip Wilson, and Elmer Isern. Mr. Reinartz is a vice-president of the Armco Steel Corp., Middletown, Ohio. As required by the bylaws, brief biographical sketches of the nominees will be published in the July issues of the journals.

Jan 1, 1952

By T. M. Geffen, R. E. Gladfelter

Lipson1 has recently presented a technical note wherein theoretical considerations were used to demonstrate. that the adsorption us saturation relation for a linear absorption method is not necessarily a single valued function of saturation.1 It was concluded that the absorption us saturation relationship is subject to the same hysteretic effect as is the flow behavior between the drainage and imbibition systems. It is the purpose of this note to show, by experimental results, that for the manner in which fluids are distributed in porous materials during fluid flow, the relative X-ray absorption us saturation relationship is single-valued regardless of the saturation history. The design of the apparatus used to measure relative X-ray absorption of cores undergoing fluid flow tests is similar to that described by Morgan, McDowell and Doty. A few modifications have been incorporated in the design to increase sensitivity and simplicity of measurement. The sensitivity is such that for usual types of cores a recording pen movement of approximately 12 linear in. is occasioned between the recording of the core dry and when it is completely full of an absorbing liquid, a solution of approximately five per cent by volume of iodo-benzene in a close-cut hydrocarbon fraction, or a solution of 50,000 ppm sodium iodide in water. Two types of experiments were conducted, one in which the liquid was inside the core, and the other with the liquid outside the core. Tests with the liquid inside the core were run to cover the saturation range encountered in both the drainage (gas drive) and imbibition (liquid flood) flow systems. It is pointed out that the same core was used, but the tests were conducted at different times with the recording mechanism balanced at a different position. Therefore, the absolute values of relative X-ray intensity at any saturation are not the same in each test. In the second type of test the same core was used, but this time its pore space cmtained only gas, and various thicknesses of oil contained in plastic cells were placed in front of the dry core. As before. the relative X-ray ah- sorption was measured and compared to the quantity of oil in front of the core. The arrangement of the fluids with respect to the path of X-rays in these two types of tests represent fluid distributions of a wider difference than can be expected between that established in a core just due to imbibition and drainage saturation flow histories. Thus any deviation from a straight line relationship of the log of the relative X-ray intensity us saturation calibration should be readily apparent. Results of the laboratory tests are given in Fig. 1. A schematic diagram showing the position of the fluids with respect to the path of the X-ray beam is given for the two cases investigated. In the case where the oil existed outside the core (Case B), the log of the X-ray intensity (log, I/I,) is related directly to the cell thickness (amount of oil in X-ray beam path). This correlation is in full agreement with X-ray theory. In the case where the oil or water existed inside the core (Case A) which covers both drainage and imbibition types of flow processes, again the relationship between absorption and saturation (amount of oil in X-ray beam path

Jan 1, 1952

By Robert E. Bush, E. S. Mardock

The objective of this paper is to present practical methods of applying radioactivity logs to problems of interest both to those engaged in evaluating fundamental reservoir data as well as to those engaged in subsurface structural work. The basic theories underlying the operation of radioactivity logging methods are briefly discussed along with some of the problems arising in the interpretation of the log. Relative methods of quantitative interpretation are described, with a discussion of relative reference lines and specific examples are given showing the application of these relative quantitative interpretation methods. To show the variation of the methods described, specimen wells penetrating formations widely divergent in point of geologic age were selected to demonstrate the application. A relative reference line is determined for the Neutron Curve and by comparison to known petrophysical data such as porosities from diamond cores, a direct quantitative relationship is developed. The application of this relative calibration curve to logs of unknown wells will permit a reasonably accurate determination of porosity in limestone and dolomite formations. Specific examples are given showing the application of these relative methods of interpretation to logs of the Smackover limestone in Louisiana, the Edwards limestone and dolomites of South Texas, and Permian dolomites of West Texas. Radioactivity logs have been used extensively by the petroleum industry for a number of years and recognition of their value has grown steadily, not only as tools to aid in the solution of specific stratigraphic problems, but also as potential sources of the basic data necessary for the estimation of net pay and reserves. The value of radioactivity logs for stratigraphic work has been pointed out in the literature,1,2,4,5,6 and now has long been recognized by the industry, but the quantitative application of the logs has advanced but little beyond the stage of a strong conviction that radioactivity logging curves will some day provide the information on such important quantities as the porosity and the liquid saturation of the formations. During the past few years the staffs of the Lane-Wells Company and Well Surveys, Incorporated, have devoted a great deal of time, thought, and experimentation to the relationships existing between radioactivity curves and the lithologic conditions encountered, and this paper is, in a manner of' speaking, intended as a progress report of this work and includes suggestions which the authors have found useful in the interpretation of radioactivity logs. The section on theory is not intended as a complete exposition of the physical processes involved, but rather as a brief introduction to the reader of these processes so that he may acquire a better understanding of the behavior of the radioactivity curves under the varied conditions encountered in normal well logging. Three relative methods for using neutron logs for the quantitative estimation of porosity in limestone or dolomite are presented. These methods are based on the comparison of logs and porosity data from wells in Louisiana, South Texas, West Texas, and New Mexico. These areas were selected because not only were there more core data available from these areas but also the majority of these data were from limestone or dolomitic zones. The correlation between core data and logs is simpler for limestones and dolomites than it is for sandstones due to the fact that sandstones are more complex than limestones and differ more widely among themselves as to composition of cementing materials, siltiness, etc. When data applicable to the various types of sandstones are available, the authors hope to present a discussion similar to this paper covering sandstones or possibly a more general discussion covering all types of reservoir rocks. The relative methods for estimating porosity which are presented in this paper fall short of the absolute method sought. However, these methods possess the advantage that they can be applied to almost any neutron log as long as the range of application is held within the limits imposed by the local lithologic conditions which prevailed during calibration, i.e., these methods are for short range application only. THE THEORETICAL BASIS FOR RADIOACTIVITY LOGGING The two redioactivity logging curves commercially available today are the

Jan 1, 1950

By G. Y. Chin, M. T. Dolan, W. L. Mammel

We have obtained by computer methods the solutions of the Taylor analysis1 for axisymmetric flow in bcc metals. Four modes of slip have been treated in detail:2-4 (111), {112}(111), {123}( 111), and a mixture of all three. In addition to obtaining anisotropy of strength data for randomly oriented or textured polycrystalline material,4 we have also obtained the lattice rotation resulting from slip on the predicted systems. The patterns of lattice rotation are essential to an improved understanding of texture development during deformation. The present note shows the results of lattice rotation for 5 pct axisymmetric compression, for fifty-two axial orientations distributed at 5-deg intervals throughout the standard stereographic triangle. The data are presented in Figs. 1 to 4 for the four modes of slip. The lattice rotation is indicated by a vector, the ends of which correspond to the positions before and after the deformation. The different vectors emanated from a given orientation represent different combinations of five slip systems that satisfy Taylor&apos;s minimum shear criterion.&apos; Fig. 1 shows the results for {110}< 111> slip. They are similar to those obtained by Bishop5 for the case of (111 )(110) slip in axisymrnetric tension, since in axisymmetric flow the sense of lattice rotation for {111)( 110) in tension is the same as that for (110) (111) in compression. The pattern of lattice rotation may be divided into three regions: region A in which the rotation is toward [100]; region B, toward [lll]; and region C, toward either [ loo] or L lll]. Although some slip combinations in region C lead to [1101, the latter is not stable as continued activity of the same combinations will eventually move the axis toward [loo] or Llll]. It may also be noted that [loo] is itself not stable. However, close inspection of the vectors in region A shows that it is impossible for an axial orientation within A to rotate outside its boundary. Hence after heavy compression, all orientations from A and some from C are expected to form a diffuse band in the [100] vicinity. By far the largest region is B. Here all orientations rotate to [lll], which is a truly stable position. Thus the [111] texture component is expected to be rather sharp. For the case of (112 }( 111) slip, Fig. 2, region C is enlarged at the expense of A, with B about the same as for {110}( 111) slip. A significant difference, however, is that [loo], as well as [Ill], is now truly stable. Fig. 3 shows the results of slip on {123}( 111) systems. Region B is substantially enlarged at the expense of C, with A being intermediate in size between the {110}(111) and {112}(111) cases. Like the case of {110)( 111) slip, [100] is itself unstable. However, the lattice rotations here are confined to less than 5 deg; hence it may be considered "stable" for practical purposes. Finally, Fig. 4 shows the results of mixed slip. Here region B is the largest, and C the smallest, of all the cases considered. Both [loo] and [ill] are stable. The behavior of the three corner positions is, in fact, identical to the case of {112)( 111) slip, Fig. 2; it turns out that in these positions for the mixed slip case, all the active slip systems (based on Taylor&apos;s criterion) belong to pure {112}( 111) .4 In summing up the results for the four modes of

Jan 1, 1968