Search Documents

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. [ ] In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. QUANTITIES AND TREATMENTS OF TREATED TIMBER PURCHASED In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required on their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1'2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger' on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.' This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1' were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

Elected Died 1895 *ABBOTT, AI ATTHUR 1908 1882 *ABBOTT, ARTHUR V 1906 1905 * ABE, MASAYOSHI 1909 1903 * ADAMS, CHARLES C. 1905 1905 * ADAMS, WILLAMS 1909 1903 * ADAMS, W. EDWARDS 1910 1884 *ADDY, MATTHEW 1896 1906 * AFFLECK, WILLIAM A. 1911 1889 * AKERS, WILLIAMS 1906 1905 * ALABASTER, RUPPERT C. 1911 1899 * ALBERGER, LOUIS R. 1911 1894 *ALLEN R B 1896 1905 * ALLEN, R. SCOTT 1906 1874 * AMIOT, H. 1892 1886 *AMSLER, CARL 1894 1898 ** ANFERSON, JOHN w. 1905 1895 *ÅNGSTROM, CARL 1901 1887 * ARCHBALD, JAMES 1910 1900 * ARLETT, GEORGE H 1906 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1905 * AUSTEN, PETER T 1907

Jan 1, 1917

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By R. D. Russell, R. M. Farquhar

SOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing iso-topic tracers to obtain information about the geological history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium Occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts comparable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample. It is this unique property of lead that serves as a means of tracing the history of a lead sample in terms of its contacts with the radioactive elements. If lead from a lead mineral has been analyzed with a mass spectrometer, the measured isotope ratios are determined entirely by the isotope ratios of primeval lead, which are identical for all minerals, and by the particular history of the sample. It follows that for samples from any particular geological area, observed differences in the isotopic composition are enough to distinguish different geological histories. An illustration of the qualitative application of this statement is given in Table I by analyses of some galenas from the western Cordillera. Samples from deposits in Pre-Cambrian sediments have very different lead isotope ratios from those of the ores in the Paleozoic sediments. Although the two types are associated closely geographically, it is apparent that they have had quite different histories and have probably been emplaced at quite different times, as the ideas outlined in the following section suggest. Even when applied quantitatively, a lead isotope analysis can never indicate a unique history of any lead sample. However, it greatly restricts the choices available and combined with other geological and geochemical data can lead to a much better understanding of the genesis of lead ores. General Character of Lead Isotope Variations: Early isotopic analyses of common leads by Nierl showed that geologically younger leads were generally richer in isotopes of masses 206, 207, and 208, with respect to that of mass 204. This regularity of measured lead isotope ratios can be easily observed by plotting each of the ratios Pb207/Pbm and Pb205/ Pb204 against the ratio Pb206/Pb204. In both graphs the points lie scattered closely about a well defined mean curve. It was immediately supposed that this regularity resulted from the growth of all leads from a common primeval lead present at some time, To, early in the earth's history. Lead in the outer part of the earth would become continually enriched in the radiogenic isotopes as a result of the uranium and thorium intimately associated with it. The subsequent extraction of some of this lead and formation of a lead mineral free of the radioactive parents provide samples of lead existing in the earth at the time of mineralization, T. Younger leads in general will be richer in the radiogenic isotopes because they have been associated with uranium and thorium for a longer time. Then lead ratios would be given by the formulae: (Pb206/Pb204)YTPb^/Pb204) +f "(u201) kdt T (Pb207Pb204)r = (Pb208/Pb204)T0 + J (U295/Pb204) k' dt T (Pb208/Pb204) t = (Pb208Pb204 + J (Th204) A." dt [1] where A, A', and A" are the decay constants of U238, U285 and Th232. Summaries of measurements of radioactivity of surface rocks, such as given by Faul,2 are of limited

Jan 1, 1958

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

PICK AND SHOVEL CLUB, CASE SCHOOL OF APPLIED SCIENCE The last meeting of the year of the Pick and Shovel Club of Case School of Applied Science was held on May 20, 1919. The speaker, Dr. Zay Jeffries, gave a very instructive and interesting talk on the Metallography of Non-ferrous Metals. The club has had a very successful year in spite of the loss of a few months time through the S. A. T. C. Among the speakers for the year were Dr. F. R. Van Horn, Dr. C. H. Fulton, and Dr. W. R. Veazey of our school; Dr. E. S. Moore of Penn. State College; Dr. Ansel St. John, of the National Carbon Co.; and Mr. V. S. Bidle, of the W. S. Bidle Co. The graduating members wish the club the best of success for the coming year. BERTRAND R. WARMELING, Secretary.

Jan 7, 1919

DAVE BARTLEY and Edwin F. Gray, miners, late of Shasta County, California, young, healthy, and "dead broke," arrived at Ely, Nevada, one evening in the summer of 1900. Before rustling jobs and going to work, they decided to look around the camp, and in pursuance of this plan they visited a number of claims owned by D. C. McDonald, Justice of the Peace and pioneer of the district. Among the claims he showed them were the Ruth (named after his daughter) and the Kearsarge. Both were regarded as possible gold or silver properties. For no very definite reason the two miners changed their plan and took a lease and option to buy the two claims for $3500. After the transaction was closed and the partners were alone, Gray asked Bartley what he thought of the ground. "If she's good for anything, it's copper" was the reply; and, so far as the records disclose, that was the first time that anyone ever thought of Ely or the Robinson mining district, as it was called, as a possible copper area. There were some slight surface indications of copper, but it is probable that the fact that Bartley had just come from a copper district had something to do with his predilection for a metal that was much despised around Ely. In any event, his hunch was good, and he spoke with the wisdom of an oracle. For thirty years prospectors had sought gold and silver around the camp. Several stamp mills and cyanide plants had been put up and a hundred shafts had been sunk, but fate had been indifferent in its rewards to the optimistic owners. Copper ore would have to be hauled by wagon, 150 miles down Steptoe Valley to the Southern Pacific Railroad, and there was scant hope of finding ore that would bear this cost. W. B. Graham, who ran the general store in Ely, grubstaked Bartley and Gray, furnishing them with food and mining

Jan 1, 1933

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By K. W. Warren, F. R. Prestridge, B. A. Sinclair

Separating oil from water may seem simple enough, but in fact, tremendous efforts have gone into this common process problem. The petroleum industry is constantly looking for better ways to separate the emulsion of oil and connate water that is pumped from the ground and its latest development, the electrostatic emulsion separator, may find an important offshoot application in hydrometallurgy. The patent-pending OSX coalescer, developed by C-E Natco, recovers entrained solvent from both raffinate and the pregnant strip liquor. It has already undergone successful testing at the Bluebird copper circuit in Arizona and is currently being prepared for testing at a uranium SX plant.

Jan 4, 1978

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pigments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 k as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut.

Jan 1, 1949

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

[Holds monthly meetings, except June, July and August, J JOHN A. CHURCH, JR., Chairman JOSEPH E. POGUE, Vice-chairman SIDNEY ROLLE, Vice-chairman EDWARD C, MEAGHER, Secretary, Texas Gulf Sulphur Co,, 41 E, 42nd St., New York M, H, MERRISS, Treasurer, 42 Broadway, New York ARTHUR NOTMAN T. T, READ Boston Meets first Monday of each winter month. EDWARD C. GEITHER, Chairman WILLIAM S. BLACK, Vice- chairman DONALD H, MCLAUGHLIN, Secretary, treasurer, Rotch Bldg,, Harvard Univ,, Cambridge, Mass. J, L. GILLISON A. G, WAITE]

Jan 1, 1928

By J. A. SINGMASTERN

THE New Jersey Zinc Co.'s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

By W. A. James

NATURE endowed the Niagara Frontier with great resources but it was the molding of these resources by the early pioneers that assured its future development. This great industrial district of New York stretches along about fifty miles of shore line on the eastern end of Lake Erie and the Niagara River, embracing the two counties of Erie and Niagara, with the city of Buffalo about in the center. This location at the junction of the eastern end of the Great Lakes and the western boundary of the State, a great focal point of land and water, transportation, guaranteed the development of the Frontier. Although the first white settlers came to this section in 1784, it was not until after the turn of the nineteenth century that real development started. Perhaps the most significant influence in the early days was the completion of the Erie Canal between Buffalo and Albany in 1825. This then monumental achievement gave Buffalo an advantage in the race for the best trade route to the Western

Jan 1, 1938

By Alfred James

Some months since, in the Johannesburg gold-fields of South Africa, the attention of the author was directed to certain statements to the effect that the gold-contents of foul or extremely dilute cyanide-solutions could not be effectively precipitated in practice by the usual zinc-method. Such statements caused all the greater surprise, because it is well known that this difficulty is not encountered in other wellknown districts, as, for example, in New Zealand, where solutions containing less than 0.05 per cent. of KCy are regularly reduced in practice to below 1 grain of gold per ton, while in Mexico and the United States almost equally satisfactory precipitations are not uncommon. As a result of these representations, however, the author visited several plants at work in the Transvaal, and noted that while at some few mines the precipitation was really excellent, at others the effluent, after treatment, was much too high in bullion-contents. An investigation into the causes of these unsatisfactory results disclosed the fact that more attention to the close packing of the zinc-shavings in the extractor-compartments tended to improve the results, even with the most dilute solutions. The function of the zinc being one of surface, it stands to reason that a compartment well filled with zinc would be more effective than a half-filled one. Moreover, the quality of the zinc was inferior. This should be in long, tough, thin, light threads; light enough to ignite readily, and tough enough not to disintegrate easily into a slime. The coarse shavings too frequently employed appear to give the reverse of the best practice ; they are brittle, contain less surface, and take up more room. It is almost impossible to pack a compartment properly

Jan 1, 1898