Search Documents

The Johns Hopkins Press, Johns Hopkins University, Baltimore, Md The Johns Hopkins Press has issued a number of books as The Johns Hopkins University Studies in Geology Five of the studies are paleontological in character; five are on geology: No. 1, The geology of the Corocoro copper district of Bolivia, by J. T Singewald, Jr and E W. Berry, $1 50, 2, The geology and paleontology of the Huancavehca mercury district, by E W Berry and J T Singewald, Jr $1 50, 6, Contributions to the geology and paleontology of South America, by E W. Berry and F M Swartz, 3175, 7, The geology of the Island of Trinidad, B W I, by G A Waring, with notes on the paleontology by G. D Harris, $1 75, 8, Fifty years' progress in geology, 1876-1926 Papers presented at the Geological Conference during the 50th Anniversary of the Johns Hopkins University, $1 50 An additional publication on geology is. Notes on the minerals occurring in the neighborhood of Baltimore, by G H Williams, 25 cents. In the list of Doctors' Dissertations available from the University are found all theses on geology and mineralogy, about 90 in number, from 1886 on Authors of many of these have since made great names for themselves in the fields of geology and mineralogy. Most of the theses have been published as papers by other agencies and, as such, will be found under other headings in this directory

Jan 1, 1933

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,' and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By Wheeler P. Davey

In an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. l.) Fig. 2 is a photograph of the end of the punching, showing the hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of radiographing metals. In order to gain some preliminary data, several pieces of 1/2-in. (12.5-mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter I.........................................1/4 in. =6.3 mm 2........................................1/8 in. =3.l mm. 3................................... 1/16 in. = 1.6mm. 4....................................... 1/32 in. = 0.8 mm. 5........................................1/64 in. = 0.4 mm. Exposures were made on Seed X-ray plates at 20 in. (50 cm.) distance with Coolidge tube X-117, operated on Scheidel-Western induction coil with mercury turbine break. The X-ray plate was placed on a sheet of 1/8in. (3.1-mm.) lead. The steel was placed above this and a Iead

Jan 1, 1916

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By AIME AIME

STEADY advance has been made in the art of lead smelting and refining during the year. The bringing of natural gas to the Salt Lake valley has led to its adaptation to lead smelting operations. The Tooele plant of the Anaconda Copper Mining Co. has put into practice the high blast pressure and constant volume for lead blast furnaces, which we understand was first advanced by John F. Austin. It would appear that within limits, capacity is nearly proportional to the volume of air. If the charge is dense, a constant pressure, as in the old practice. did not get much air through the charge and the furnace slowed up. The constant volume idea makes the charge smelt at the same rate as if the charge were porous. The cost of a little additional power insures capacity operation at all times.

Jan 1, 1932

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By C. W. Spencer, F. N. Rhines, R. J. Knight

Ametallographic study has been made of the peritectoid transformation as it occurs in two Ag-A1 alloys, containing 6.0 and 6.9 wt pct Al, respectively. After equilibrating at 475°C, these alloys were transformed isothermally just below the peritectoid temperature which lies at about 450°C.1-3 Peritectoid transformation in this alloy system consists in the reaction of a and 5 to form µ. The crystal structures of the a, µ, and 5 phases have been determined as face-centered-cubic, 6 manganese, and hexagonal-close-packed, respectively. At the peritectoid temperature their equilibrium compositions are approximately 5.85, 7.02, and 7.24 wt pct (19.92, 23.2, and 23.8 atomic pct) aluminum."" The transformation might be expected to occur principally at the interface between the a and 5, but such is not the case. Instead, the major part of the transformation occurs by the direct (and perhaps initially diffusionless) conversion of 5 to µ. The composition range of the forming µ nearly overlaps that of the parent at the temperature of transformation" so that little, if any, composition change is required. Transformation proceeds by the nucleation of µ at points upon the external surface of the sample and sweeps through the 5 phase, leaving the a initially almost undisturbed. Subsequently, the a phase participates in the transformation by being partly or totally converted to µ. Specimens approximately 1/4 x 1/4 x 1/16 in. were cut from cast ingots, previously equilibrated 68 hr at 588°C. The specimens were held for 3 hr at

Jan 1, 1958

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated'

Jan 1, 1967

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

By B. Egeberg, H. B. Smith

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By C. R. Keyes

Discussion of the paper of C. R. Keyes, presented at the Chattanooga meeting, October, 190S, Bulletin No. 26, February, 1909, pp. 119 to 166. E. R. BUCKLEY, Flat River, Mo. (communication to the Secretary*) :-Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seem to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes's original statements in quotations. Referring to the Ozark dome: (P. 127.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known' rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (P. 138.) " . . . the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that .produce in effect basins in which' the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore- bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel¬erate the flow of ground-water rather than retard it. I might name the open, breeciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Oct 1, 1909

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation

Jan 4, 1953

By R. R. McNaughton

The Consolidated Mining and Smelting Company of Canada, Ltd. at Trail, B. C., inaugurated a comprehensive program of investigation about 15 years ago to develop the most economical process of recovering the metal in the large accumulated stock of by-products of the lead smelter and the zinc plant. Two principal methods of recovery were followed to a successful conclusion—an electrothermic process to treat zinc-plant residues and cold slag and the fuming of hot slag from the lead blast furnaces. The latter was selected because it showed a saving over the former in its ability to handle hot blast-furnace slag, thus obviating the necessity of granulating, handling and eventually remelting the same slag for the electrothermic process. The design of a fuming plant was commenced in 1928, and construction, which was started immediately, was completed in July 1030. Operating intermittently for a general tuning up, the plant was officially blown in for regular operation in August. During this month the vagaries of a slag-fuming plant were studied and an operating crew was trained. A history of slag fuming at Trail and the development of plant design is given in a paper by G. E. Murray in the Transactions of the Canadian Institute of Mining and Metallurgy for 1933. Fuming Plant The fuming plant at Trail (Fig. 1) is a separate unit although of necessity interlocked closely with the lead smelter. The plant consists essentially of a fuming furnace with its accessories, a waste-heat boiler followed by an economizer, and a suction-type baghouse. The plant was built as the first of two 400-ton units with the intention of adding the second unit within a year, so that flues, fans and buildings were built to handle double the original load. Furnace.—The furnace as originally built (Fig. 2) was of water-jacket construction, 10 ft. wide, 20 ft. long and 6 to 10 ft. high. The roof height was made variable to check experimental work, which had indicated that this dimension affected the rate of reduction. Coal and air were supplied

Jan 1, 1937

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

By H. A. Lesser, H. L. Stone, G. H. Bruce

ESSO PRODUCTION RESEARCH CO., HOUSTON, TEX. A mathematical model that represents the conduction heating of a rock formation of limited permeability is formulated. Heat is introduced by the injection of a hot condensing gas into horizontal fractures through the formation. The fractures are assumed to be equally spaced; the flow of fluid is linear. The model consists of three coupled partial differential equations and two functional relationships. Temperature histories for both fractures and formation are obtained by numerical procedures. Application of the model in predicting in situ heating of oil shale is illustrated with four sample cases. Influences of shale thermal diffusivity, fluid pressure in the fracture and fracture spacing upon heating rate are demonstrated. In all cases considered, several years were required to heat all the formation to 700F with 1,000F steam. Less than 32 per cent of the injected heat was utilized for heating the shale. To facilitate extensive calculations of this type, a set of seven dimension-less quantities are derived. With this dimensionless system, the effect of controllable parameters on economics can be explored. INTRODUCTION Vast deposits of hydrocarbons are contained in oil shale formations in the western United States and in other countries. These hydrocarbons, known as kerogen, are difficult to recover because they are immobile solids and because the rock formations in which they are found have very limited permeability. The kerogen can be converted through pyrolysis to recoverable liquids and gases if the formation temperature is elevated to the range 600 to 800F. To accomplish this heating, the formation might be artificially fractured and a hot fluid injected into the fractures. If the injection and production wells are vertical and the fractures horizontal, interwell communication will be established and the hot fluid will flow from an injection well to a production well. In this process, some of the heat in the fluid will be given up and conducted into the formation. Products of pyrolysis will flow from the heated rock matrix into the fractures and be produced, commingled with the injected fluid. The practicality of such a process is strongly influenced by the rate at which heat can be transferred from the hot fluids to the formation. An analysis of this heat conduction problem is the subject of this paper. Linear flow of a condensing gas through a set of horizontal, equally spaced fractures is considered. Temperature histories for both fractures and formation are obtained from numerical procedures. The analysis also applies to formations containing streaks of natural permeability instead of fractures. Heat flow problems similar to the one treated here have been studied by other workers. Thomas1 has solved a radial problem in which he considers the injection of a noncondensing gas into a single, horizontal fracture and approximates the temperature profile in the fracture by a step function. The solutions to other problems, which are less similar to the present problem than the one treated by Thomas, have been reviewed by Spillette.2 In addition to these mathematical studies, a field test of an in situ shale oil recovery process using hot natural gas as the injected fluid has been reported.3 The first part of this paper is concerned with the mathematical development of the problem. The differential equations, boundary conditions and functional relationships which describe the physical model are formulated and the equations are cast into finite difference form. The method of solution of the difference equations is discussed (Appendix B). The second part of this paper presents results computed for a typical oil shale formation for which steam at 1,000F is the injected fluid. Fracture spacing, horizontal and vertical thermal diffusivities

Jan 1, 1967

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980