Search Documents

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Apr. 10, 1918, to May 10, 1918. BALLARD, JOHN I Supt., Cable Mining Corpn., Cable, Mont. BURKMAN, JOHN M. F., Constr. Engr., U. S. Smelt. Refin. & Min. Co., Care -University Club, Mexico City, D. F. CALLEN, ALFRED COPELAND, Head, Mining Engineering Dept., West Virginia University Morgantown, W. Va. CHADWICK, LAWRENCE, Chem., Mt. Elliott Copper Co., Ltd., Selwyn, via Townsville, North Queensland, Australia. CODY, FRANK W., Skimmer, Reverberatory Furnace, Arizona Copper Co., Clifton, Ariz. COOLBAUGH, MELVILLE F., Prof. of Chem., Colorado School of Mines, Golden, Colo. DODGE, ALLAN WAYNE The Dodge Agency, 104 East Iron Ave., Salina, bans. DONNELLY, LEONARD G., Pet. Geol., Sinclair Oil & Gas Co., Sinclair Bldg., Tulsa, Okla.

Jan 6, 1918

The problem of surface support in coal mining is naturally divided into three branches: 1. Surface covered with improvements of such value as compared with the value of the underlying coal, or with such elements of danger to mining, that absolute support is essential. 2. Surface with improvements of less value than the underlying coal such that moderate settlement may be permitted, but destructive settlement must be avoided, either by reason of danger to human life or unwarranted property damage. 3. Surface of relatively small value as compared with the underlying coal where destructive settlement may be permitted. First Problem In the first case it is evident that the original support must be maintained either (a) by leaving ample pillars and confining the coal recovery to a very conservative first mining, (b) by so supporting less conservative first mining by filling or flushing that the gradual deterioration of the pillars may be prevented and subsidence avoided, or (c) by incompressible support as masonry either as an adjunct to insufficient pillars or in place of the original coal support. a. From tests made by the Scranton Engineers Club, it appears safe to figure on 2000 Ib. per sq, in. as the safe squeezing strength of coal pillars in place, provided that these are, as usual, not higher than their least horizontal dimension; and from this figure the percentage of pillar to be left for various depths may be easily calculated. For safety in this

Jan 1, 1930

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By J. C. Jaeger, G. A. Wiebols, N. G. W. Cook

It is usual practice in engineering to design a stable structure by ensuring that the stresses in the elements of the structure are always less than their strength, which may be defined as the yield stress, the ultimate stress, or the fatigue stress, according to the type of the load. Such restrictive design is not practical in the design of underground excavations since the rock surrounding such structures is usually failed, but only occasionally does this give rise to instability of the structure. Thus, while the usual criterion for the design of a stable structure is certainly sufficient, it is not necessary for underground excavations. A proper understanding of the conditions necessary for stability is vital to the useful application of rock mechanics knowledge to the design of underground structures. Most tests on the properties and strength of brittle rocks are disrupted at or near maximum load by the rapid release into the specimen of energy stored in the resilience of the testing machine. This is in contrast with a phenomenon, which may be observed frequently, where the rock immediately surrounding an excavation is both failed and subject to stress. By postulating a complete stress-strain curve for rock, it can be shown that failure is unstable or stable, depending upon whether the stress-strain curve of the rock lies inside or outside the stress-strain characteristics of the applied stress. Stability is, therefore, a function of the stiffness of the system applying the stress relative to that of the failing rock. Many workers have established that the strength of rock specimens under a lateral hydrostatic confining stress varies linearly with confining stress, in a way which may be expressed by the equation CT=Co+K[o]3

Jan 1, 1972

By George H. Found

During recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" 06 a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating -mecha-nisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experi- mental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,' damping due to localized inelastic stress relaxation at inhomogeneities within the meta1,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.' How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables ham been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About Ioo hr. after straining, a stable value is reached of magnitude proportional to the amount of strain.' In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963

By J. R. Long, R. S. Dean, F. S. Wartman, E. T. Hayes

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By W. J., Kroll

MOST people believe that rare metals are always, scarce in nature, expensive to make, and therefore useless despite some miraculous properties which might make them a cure-all. There are' some metals, which are quite frequent in nature, such as zirconium, which are called rare only because our present methods for making them are elaborate, thus forcing the manufacturer to sell them at a high price. There are also truly rare metals, such as gallium, which do not occur frequently in ores, but are easily reducible from their oxides. In these cases the price of the concentration operation is the decisive factor. The distribution of the elements in the earth's crust is no indication as to the availability of a metal; the concentration operation is the critical factor. Concentration is frequently obtained in the course of metallurgical operations for the extraction of other metals, and the rare metal may be enriched in by-products, flue dusts, mother liquors or precipitates from electrolyte purification as are indium, thallium, selenium, and tellurium. A periodic table of the rare elements may serve as a basis for discussion of their properties and to establish a program. (Table 1.)

Jan 1, 1946

By P. Pollard

A method has been developed for evaluating acid treatments in fractured limestone fields by breaking down pressure drawdown into three component parts: (I) pressure differcntial across "skin" near the borehole face, (2) pressure differential due to flow resistance in the coarse communicating fissures and (3) pressure differential between the fine voids and the coarse fissures. It is apparent that in most successful acid treatments the first term, skin resistance, has been reduced or eliminated. Further, it is often possible to estimate the volume of coarse fissures associated with the second term, coarse fissure flow resistance. In cases where this volume is comparable with practical acid volumes it seems likely that this resistance also may be attacked with a suitably retarded acid. INTROD UCTION Acid treatment has been successfully applied as a general practice in the limestone wells in the Mara/ Maracaibo districts of Venezuela for some 10 years. At the same time the need has been felt for a more precise method of: (1) evaluating the effect of an acid job and (2) selecting wells which should benefit from an acid treatment. The following method, based on an analysis of build-up curves for wells producing from fractured limestone, provides a means of forecasting the effect acid will have on a well and in many cases the probable order of production rate increase which may be expected. In certain cases it is also possible to calculate the fissure volume through which the acid has to be displaced for best results. Various approximations are introduced in the method, but within the limitations of these the analysis gives an indication of how a well, whether previously acidized or not, may be expected to respond to acid treatment. Suitable build-up curves cannot be obtained on "tight" wells which do not give sustained production and the method is not applicable to such wells. Figs. 1 through 7 illustrate various types of build-up curves obtained from limestone wells in Western Venezuela. Curves are included showing (1) both skin and coarse fissure resistance, (2) skin resistance only, (3 and 4) reduction of skin resistance by acidization, (5) fissure resistance only, (6) reduction of coarse fissure resistance by acidization, and (7) acidization failure. This theory has been successfully applied for over three years during which 22 acid treatments have been carried out specifically to reduce skin resistance and three treatments to reduce coarse fissure resistance. The method has been found to be a useful aid in the selection of wells for acidization.

S. F. EMMONS RESEARCH FELLOWSHIP. The movement was started by a number of the friends and admirers of the late S. F. Emmons, Economic Geologist of the United States Geological Survey, to perpetuate his name through a fellowship to be known as the ?S. F. Emmons Research Fellowship," and they have succeeded in raising some $13,000 for the purpose of carrying on research work in economic geology. The Committee in charge of this Memorial Fund has succeeded in obtaining the co-operation of Professors Kemp, of Columbia, Irving, of Yale, and Lindgren, of Massachusetts Institute of Technology, in the administration of this fellowship. These three gentlemen are respectively geologists of the institutions mentioned and are exceptionally qualified to determine in what direction the fund can be best administered. It is hoped that additional contributions will be forthcoming from many who have heard of this movement. Subscriptions are invited and may be sent to any one of these gentlemen, or to Benjamin B. Lawrence, Treasurer, No. 60 Wall Street, New York City.

Jan 10, 1913

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By F. N. Rhines, A. H. Grobe

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By Frank Haas

Many articles on the physical properties of fire damp have appeared in the Transactions and elsewhere but practically nothing has been written in regard to its occurrence or fluctuation in quantity in an ordinary mine. After the Monongah explosion in 1907, with the loss of 361 lives, the Consolidation Coal Co. sought a method by which such catastrophes could be prevented. While the cause of this particular explosion was attributed to coal dust, some of those acquainted with the mine thought that fire damp was involved, if it was not the initial cause. So the literature on the subject was studied and mines where similar conditions prevailed in this country and Europe, were visited, with the view of establishing some system by which gas could be more easily detected and controlled. The results of this study were disappointing for no method was found other than the time-honored fire boss with his safety lamp, with some variations in the rules and regulations governing his inspections and reports. Duties of the Fire Boss Pending the development of a better method, it was decided to standardize and perfect the duties of the fire boss and the reports based on his observations. Those who were then in service were closely examined, various lamps were experimented with and the lamps and individuals tested under known conditions. It was found that a fire boss could tell whether gas was present but his estimate of quantity was not even an approximation; therefore, while the services of fire bosses were indispen-sible there was need of additional information by which the quantity of gas could be estimated with some precision in order to determine its variation from time to time. Chemical Process for Determination of Methane After considering all methods known at that time a chemical process was adopted. The principles involved in the process are that in an enclosed receptacle, in the presence of excess air, methane will be completely burned by means of a hot platinum wire to carbon dioxide and

Jan 1, 1927