Search Documents

By A. N. Winchell

Petrographic studies of over 1400 rock and mineral samples, and studies of their field relations, show that there is a complete gradation between sandstone and limestone; the lime-silicate rocks were produced by recrystallization of limestone; mineralization and silicification occurred after silication and at considerably lower temperature; carbonation occurred at still lower temperatures. IN CONNECTION with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Bingham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance.

Jan 3, 1924

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By H. S. McQueen

The insoluble-residue method for the examination and correlation of limestones and dolomites, or other sedimentary rocks containing calcium and magnesium carbonates, originated and was developed in the laboratory of the Missouri Geological Survey. The numerous and ever-increasing problems in the field of applied geology, and the need for a tool or aid in the solution of them, led to experimental work with samples collected from deep wells, in the early part of 1924. The success attained, almost at the outset, with this method was so great that the method has now been developed from the state of the experimental to the realm of large-scale, every-day routine. In a previous paper the writer1 described the procedure in detail and the characteristics of the residues obtained from certain Paleozoic formations in Missouri. The purpose of the present paper is to discuss the economic application of the insoluble-residue method. Developmental History Within the Ozark region of southern Missouri the geologic column consists of Lower Ordovician (Canadian of Ulrich) and Upper Cambrian formations, which are composed mainly of dolomite with subordinate amounts of sandstone, shale and limestone. Chert is found to some extent in all except one of the dolomite formations. The stratigraphy of the region is complex because the dolomites have lithologic similarities, fossils are few and often poorly preserved, and identifiable horizons within the comparatively thick formations are not common. Although considerable stratigraphic work of an areal nature had been done for a period of many years by the Missouri Geological Survey, the detailed geologic succession had not, until a few years ago, been systematically worked out. The problems of subsurface stratigraphy were even more complex. This region constitutes the main ground-water province of the State of Missouri and within it wells of varying depths are drilled in order to obtain supplies of ground water. In the work of the State Geological Survey in connection with the drilling of water wells for public supplies * Published with the permission of the Director, Missouri Geological Survey and Water Resources. Manuscript received at the office of the Institute Feb. 20, 1936. Assistant State Geologist of Missouri; Missouri Geological Survey, Rolla, Mo. References are at the end of the paper.

Jan 1, 1937

By J. F. Held

In a study of the influence of cold rolling on mechani cal properties of steel, it was found that the specific rolling procedure influenced crystallographic orientation. Properties developed by several rolling modes were determined and related to crystallographic orientation. Sanzples were cold-rolled various amounts on a laboratory mill. When palm oil was used as a lubricant, the crystallographic orientation was homogeneous throughout the thickness of the samples. Other samples were rolled without lubrication. Variations in intensity of the recrystallization texture components persisted throughout more than 50 pct of the volume of these samples. When the average plastic strain ratio, which is dependent upon crystallogvaphic orientation, was plotted as a function of percent reduction, a maximum was found at 40 pct in the samples which contained the observed texture variation. No maximum was found for the samples with the homogeneous texture distribution. Other mechanical properties, such as tensile strength and yield strength, were not influenced by the variation in crystallopaphic orientation. MECHANICAL properties of steel sheets depend, in general, upon the structural properties of the steel. For example, the Petch equation describes the relationship between yield strength and grain size. Other properties, such as hardness, vary with chemical composition. The plastic strain ratio, or R value, has been found to be dependent upon crystallographic orientation . In the course of investigating the effect of cold rolling on mechanical properties, it was found that a previously reported relationship between percent cold reduction and R value was not always observed. Published data had shown that the optimum cold reduction for best R values is 70 pct for aluminum killed steel.' However, by altering the rolling conditions, the optimum reduction can be shifted to much lower values, or it can be moved to very high values. This paper describes the rolling conditions that lead to shifting of the optimum cold reduction. The effect of rolling conditions on the various structure parameters and the resulting mechanical properties are evaluated. EXPERIMENTAL PROCEDURE Samples of three low-carbon aluminum killed steels were cold-rolled various amounts on a 9-in.-diam 2-high laboratory mill. Hot-mill thermal practice and steel chemistries are listed in Table I. Steel A was rolled with palm oil lubrication and heavy reductions on each pass; i.e., a total reduction of 75 pct was ac- complished with a maximum of five passes. Steel B was rolled without lubrication, and light reductions were given on each pass. After approximately 75 pct reduction, it was necessary to use a small amount of light oil to achieve any additional reduction in thickness. Following cold reduction, the samples were box-annealed at 1300°F for 10 hr. The heating rate between 800" and 1300°F was 50°F per hr, and the cooling rate following the soak period was 50°F per hr. Tensile specimens were machined from the annealed material and these were used to measure yield strength, tensile strength, and the plastic strain ratio (R value). Recrystallization textures were determined by an inverse pole figure technique.*'3 Integrated intensities of the (110), (002), (112), and (222) reflections were recorded for those planes lying parallel to the sheet surface. Examinations were made on both surfaces of each sample, and also at various levels beneath each surface to approximately 0.010 in. depth by etching techniques. RESULTS R Values. The R values obtained in steels A and B are shown as a function of percent cold reduction in Fig. 1. No optimum cold reduction was observed in steel A, rolled with palm oil lubrication. It is likely, however, that an optimum reduction would have occurred had higher reductions than 88 pct been employed. The optimum reduction in steel B occurred at 40 pct. The behavior in both of these steels is quite

Jan 1, 1968

By H. H. Uhlig

SINCE its first mention in the literature in the eighteenth century1,2 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ? Faraday,7 in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the poten-tial at which a negative ion (e.g., Cl-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By P. G. Beckett

THE problem of handling the large quantities of water encountered in the Old Dominion mine presents many features of interest. In the present paper are discussed the probable sources of water, the pumping equipment, the increased flow into the mine in the early part of 1915, culminating in the flooding of the 18th and 16th levels in March of that year, and the difficulties that were met with during the high-water period. I. PRELIMINARY The Old Dominion mine, situated 1 mile north of the town of Globe, Ariz., has long been one of the prominent copper producers of the State, and until the opening up of the copper schist deposits in the neighboring mines of Miami, was responsible for the greater part of the copper output from the Globe district. As the gradual exhaustion of its orebodies near the surface led to the downward development of the mine, more water was encountered in the western portions directly underlying the dacite formation until the drainage problem became a serious factor in the operation of the mine and in the economical extraction of the ore. A heavy inrush of water on the 10th level of the mine in 1906, preceded by still earlier water difficulties, rendered imperative the immediate installation of a pumping equipment capable of handling large flows of water. While the Old Dominion has been recognized as a wet mine since its early clays and one in which the complete control of the water situation was of paramount importance in the development of the lower levels, it is chiefly in the last nine years, since the installation of the increased pumping equipment, that the mine has developed and handled large quantities of water.

Jan 4, 1916

By H. A. Guess

For a number of years I have used for the commercial wet assay of lead generally the ammonium molydate, and occa-sionally the ferrocyanide method. These well-known methods need no detailed description here. In the ore-selling and ore-buying establiahments of the West, 90 per cent. of all wet lead-assays are made by one or the other, and at least nine-tenths of this proportion by the molybdate method. A procedure so well-established must have merit; and, in

Jan 1, 1905

By T. M. Girdler

IN THESE perilous days of world- wide uncertainty, this Institute and the profession represented by it take on new importance in the economic life of the nation. I have long been impressed by the fact that the objects of the A.I.M.E. are purely professional and scientific. The country has benefited from your honorable tradition of adherence to those objectives over a period of 68 years. The Institute's policy of refraining from controversial matters - has made possible the serious, balanced, and uncolored consideration of the particular problems that come before it.

Jan 1, 1939

By Walter S. Weeks

CONFUSION appears to exist in the discussions of fan testing because engineers do not agree on what energy should be credited to the fan in certain cases, and because certain terms that are used in the discussions seem to have double meanings. The purpose of this paper, therefore, is to discuss the useful energy that should be credited to the fan and the methods of determining this energy, and to suggest changes in nomenclature for the sake of clearness. The instruments commonly used in the measurement of fan pressures are the manometer, the static tube, and the impact tube. The static tube is a tube with small pinholes in it. When connected to one leg of the manometer and placed in the air current with the holes facing at right angles to the direction of the current, this tube causes the manometer to register the static pressure, unaffected by the impact of the air. The impact tube is a tube with an opening that faces the air current. When connected to one leg of the manometer, this tube causes the manometer to register a pressure which is the static pressure modified by the impact of the flowing' air on the end of the tube. If the static tube is connected to one leg of the manometer and the impact tube to the other leg, and both instruments are inserted close together in the air current, the static pressure is eliminated and the manometer registers the impact pressure. The efficiency of a fan is the percentage of the expended power utilized in useful work. The items to be included as useful work are a matter of convention, and as the conventions are not universal I feel that the matter is open to discussion.

Jan 1, 1929

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By A. F. Taggart

THE following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laboratory at the Columbia School of Mines during the years 1926 to 1928-inclusive. CLASSIFICATION OF EXPERIMENTAL WORK The experiments performed may be grouped for purposes of description under the following general -headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils) c. Action of dissolved collecting agents. II. Frothing agents. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. SUMMARY OF THE ORIGINS OF PRESENT-DAY FLOTATION PRACTICE The first practicable, foolproof method of froth flotation was described in U. S. patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.1 The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when' compared with those used today.

Jan 1, 1929

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By E. H. Roberts, L. G. Swenson, F. C. Nix, R. A. Morgen

THE binary system lead-antimony has been the subject of comprehensive investigations in these laboratories by Dean' and his associates. The effect of a third constituent on this system, particularly on the lead-rich alloys in which dispersion hardening was found, has a commercial value as well as an academic interest. This paper covers the effect of the addition of copper, bismuth and tin, all of which are likely to be found in commercial lead-antimony alloys, and is divided into three parts, as follows: I. The System Lead-Antimony-Copper II. The System Lead-Antimony-Bismuth III. The Lead Corner of the System Lead-Antimony-Tin These three systems are of three different types, and hence may be considered as covering three general kinds of additions. Bismuth forms no compounds with either lead or antimony and forms solid solutions with both. Copper forms several compounds with antimony as well as solid solutions but with lead it forms a two liquid layer system and no appreciable solid solution. Tin is soluble in both lead and antimony in the solid state and also forms a compound with antimony. The effect of small amounts of bismuth on the lead-antimony alloys is small, having no appreciable effect on the solubility of antimony. The temperature of the solidus floor is lowered appreciably by the presence of bismuth, cutting down the range of heat treatment. Copper, on the other hand, due to compound formation, increases the apparent solubility of antimony. The excess antimony is tied up with the copper finally and so is not available for dispersion hardening. The net result of addition of small amounts of copper is to shift the dispersion hardening peak of the

Jan 1, 1928