Search Documents

By G. F. Comstock

These notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."l In that paper and the resulting discussion, several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8-in. (9.5-mm.) steel plate, about 21/4 by 13/4 in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extended through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what Mr. Miller called cem-entite and Mr. Jeffries martensite, while Mr. Ruder and Professor Boyls-ton think that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Pig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1920

By W. R. Phibbs

THE blast furnace of the Columbia Steel Corpn., at Ironton; Utah, was put in blast April 30, 1924, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PER CENT. Moisture 3.90 Volatile 39.00 Fixed carbon 51.10 Ash.... 6.00 Sulfur : 1.07 The analysis of the coke is: PER CENT. Volatile 0.55 Fixed carbon :...:.::: :..:.:: 89.70 Ash 9.75 Sulfur 1.05

Jan 1, 1928

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

Taking advantage of the lessons in administrative organizations which were taught by the war, Director Van H. Manning has put into effect a new form of organization in the Bureau of Mines. The Bureau is divided into two branches, one the investigations branch and the other the operations branch. F. G. Cottrell, who has been chief metallurgist of the Bureau, has been promoted to the position of assistant director and will be in charge of the investigations branch. F. J. Bailey, who has been chief clerk of the Bureau, has been placed in charge of the operations branch with the title of, assistant to the director. All research and technical control will be exercised through the investigations branch, while the non-technical work, administrative duties, and dissemination of the results of the Bureau's activities will be handled by the operations branch. Under the investigations branch comes the division of mineral technology, in charge of Dr. C. E. Parsons; the division of fuels, under the chief mechanical engineer, 0. P. Hood; the division of mining, under the direction of George S. Rice, the chief mining engineer; the division of petroleum and natural gas, under the direction of J. 0. Lewis, the chief petroleum technologist; and the division of experiment stations, under the direction of D. A. Lyon.

Jan 9, 1919

By W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1,? Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses.

Jan 1, 1935

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929

Admissions: Joseph C. Gordon, Chairman K. F. Anderson Allen B. Gibson H. J. Gruy R. F. Madera Dan H.-McLendon K. W. Robbins Aurel E. Smith W. F. West Advertising: John. D. Wisenbaker, Chairman Bernard F. Klein Henry N. Lyle R. E. Howard Clark R. Edgecomb, Jr. [ ]

Jan 1, 1961

By J. Weertman

The paper of Gifkins and Snowden considers the interesting but difficult problem of determining the stress dependence of secondary (steady-state) creep at low stresses. These authors have concluded that at stresses below 250 psi (2 x 107 dynes per sq cm) the secondary creep rate of lead is proportional to the stress (viscous creep) and is not proportional to the stress raised to about a fifth power. The experimental data considered by them were obtained on tests conducted at room temperature and at 50°C. The lowest stress employed was 50 psi (3.5 X 106 dynes per sq cm). The authors pointed out the main difficulty in determining the stress dependence of creep at low stresses. The creep tests must be run for very long lengths of time. However they made no estimates of when an experimental creep rate determination must be rejected because it does not represent a true steady-state or minimum creep rate. In order to be certain that a creep curve is within the steady-state region, the total creep strain should be of the order of 0.1 to 0.2. For a creep test of a year's duration this requirement implies that a secondary creep rate smaller than about 10-3 per hr cannot be measured reliably. The corresponding creep rate for a 10-year test is 10-6 per hr. The creep rates of the tests that were considered by the authors to prove the existence of viscous creep were of the order of or less than 10-6 per hr. One can conclude reasonably that this data does not prove unambiguously that large strain steady-state creep rate of lead is proportional to the stress in the stress range of 50 to 250 psi (3.5 x 106 to 2 X 107 dynes per sq cm). Another technique can be used to obtain the stress dependence at low stress levels. The creep rate is a very sensitive function of temperature. The creep rate can be increased by very large amounts merely by increasing the temperature. We carried out steady-state creep tests on lead single crystals25 at temperatures up to 320°C. We were able to obtain creep rate data down to stresses as low as 35 psi (2.5 x 10' dynes per sq cm). Our smallest creep rate was 8 x 10-5 per hr. Thus we obtained large strain, steady-state creep rates to even lower stresses than were considered by Gifkins and Snowden. No evidence was seen for viscous creep. The creep rate was proportional to the stress raised to about a 4.5 power down to the lowest stresses. Since there is no reason to believe that changing the temperature should change the stress dependence of steady-state creep, we feel that large strain viscous creep does not occur in the stress range quoted by the authors for lead single crystals or large-grain polycrystalline samples of lead. This conclusion does not imply that viscous creep may nat occur in a lower stress range or in the same stress range for fine grain material or at creep strains very much smaller than 0.1. Support by the U.S. Office of Naval Research is acknowledged. Authors' Reply R. C. Gifkins and K. U. Snowden We thank Dr. Weertman for his discussion and although, as we hope to show, we do not agree with his reservations, we do concur in stressing the importance of ensuring that creep rates are reliably obtained. Dr. Weertman appears to be content to accept n = 1 for low stresses with fine-grained material but not for single crystals. We believe our results show that the former result cannot be accepted without also accepting the latter. We will also show that the probable errors in our minimum creep rates are insufficient to alter our conclusions, that the criterion proposed by Dr. Weertman is arbitrarily restrictive and his alternative experimental approach possibly invalid. 1) A principal result of our Fig. 1(a) is that n = 1 for polycrystalline specimens at room temperature and 50°C for stresses below -250 psi. There was evidence that crystal slip and grain boundary sliding contributed approximately equaily to the overall strain in this low-stress regime. This implies that either a) grain boundary sliding controls slip within the grains or b) both grain boundary sliding and crystal slip independently occur according to mechanisms which give n = 1. Alternative a does not seem acceptable, so we were forced to consider b. This led us to reexamine work on bicrystals by Strutt and Gifkins and plot curves Fig. l(b). Previously Strutt et al. (loc. cit.), had merged these points with others using the Zener-Holloman parameter and thus, we now believe, had been led to overlook the behavior where n = 1. Curves C and D in Fig. l(b) did appear to confirm the hypotheses that n = 1 for crystal slip at these low stresses and the sliding curve F was similarly of the expected form. It was comparatively easy to find a quantitative theory to account for n = 1 for sliding and the similarity of curves C and D to curve F (all obtained from the same set of specimens) led us to feel that the single-crystal curves were valid. 2) We believe the secondary creep rates for both the polycrystalline and single-crystal specimens to be in error by factors c2. In Fig. 6 creep curves for polycrystalline specimens of lead(1) and lead(II) are reproduced as curves a and b, respectively, and curve c is for a single crystal at 100 psi. It is clear that, although the attainment of secondary creep rate takes 2 years for a and 150 days for b, thereafter the curve is linear for periods of 7 and -1 year, respectively. The single crystal has a linear portion commencing after 20 and extending to 90 days. Creep extension was measured directly using a traveling microscope reading to 0.01 mm on gage lengths marked on the specimens; the gage lengths

Jan 1, 1968

By C. H. Green

Recently two papers on the structure of eutectics were read before thc British Institute of Metals, one by F. L. Bradyl and the other by A. Portevin. 2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches, the writer has been working along the same line for some time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which separate out simultaneously or alternately. From the surface pattern, the eutectic means a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the proeutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 1, 1925

By C. H. Mathewson

(New York Meeting, February, 1916) DURING the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform conditions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,1 in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent. reduction of area by rolling

Jan 1, 1916

By N. B. Davis

I. Introduction. II. Definition of Plasticity. III. Theories of Plasticity. A. Structure of the clay particles. (1) Fineness of grain. (2) Plate structure. (3) Interlocking particles. (4) Sponge structure of particles. B. Presence of hydrous aluminum silicates. C. Molecular attraction between particles. D. Presence of colloidal gelatinous matter. (1) Review of theory of colloids. (a) Suspension colloids. (b) Emulsion colloids. (2) Experiments. IV. The Formation of Clays. A. Residual clays. B. Transported clays. V. Summary. VI. Conclusion. I. IntRodUction While working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity. This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 1, 1915

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

By L. V. Gregor, C. F. Aliotta, P. Balk

The structure of silicon surfaces, thermally oxi&zed in dry oxygen and in steam, was studied using the electron microscope. It was found that the structure on the original (etched) surface is retained at the outer surface of the oxide, whereas the oxide-silicon interface is smoothed out considerably. This supports the idea that, both in oxygen and in steam, the oxidation reaction occurs at the oxide-silicon interface. Mechanical damage of the original silicon surface affects the rate of oxidation. It also changes the chemical properties of the oxide, as shown by the enhanced rate of etching in buffered HF at the locations of damage. However, the oxide at the originally damaged surfaces still exhibits a high electrical breakdown strength. Exposure of thermal oxides to P205 or BzOs vapor, which will yieldphospho- or borosilicate layers, results in complete annihilation of all fine structure on the surface. Reaction of silicon with C02 gives a surface film which probably does not consist of pure SiO,. THERMAL oxidation of silicon yields uniform and strongly adhering oxide films which are normally amorphous and continuous. Contamination and surface imperfections have been reported to cause local crystallization and the formation of pinholes."' The parabolic-rate law of film growth observed by several workers for the oxidation both in steam and in dry oxygen at higher temperatures suggests that diffusion of one or more reactants through the oxide is the rate-deter mining step. One of the dif-fusants is an oxygen species and oxide is continuously formed at the oxide-silicon interface. This was concluded for high-pressure steam oxidation by Ligenza and spitzer5 from an infrared-absorption study of the isotopic exchange of oxygen. Jorgensen arrived at the same conclusion for the oxidation in dry oxygen by measuring during oxidation the resistance change between silicon and a porous platinum marker electrode in the oxide. Recently, Pliskin and Gnall' reported similar conclusions concerning the growth mechanism from controlled etch studies using a phosphosilicate marker. The work communicated in the present paper was aimed at studying oxide growth on locally damaged silicon substrates and relating it to the chemical behavior and electrical breakdown properties of the films. Since etched and oxidized silicon surfaces normally appear to be very smooth when examined by optical microscopy except for some occasional pits, it was decided to use the electron microscope as a tool. In this way, the detection of surface roughness and damage on a scale comparable to or smaller than the thickness of the film is possible. Also, the microstructure of the original substrate surface constitutes a built-in marker which represents a minimum of perturbation to the growing oxide layer, and no foreign material is introduced. Thus information on surface reactions and additional evidence on the location of oxide formation in steam and in oxygen could be obtained. EXPERIMENTAL Electron micrographs7 were obtained using a Philips EM100 electron microscope. Collodion surface replication was used since this is a nondestructive technique and thus permits replicating the same surface at different stages of processing. In order to establish the effect of different treatments it was found essential to make successive observations of the same area by using a reference point. Reference points were conveniently provided by scribing a small v mark on the original surface with a silicon carbide tip. This procedure yields damaged and damage-free areas near the reference point. Upon replication, the samples were thoroughly cleaned before subjecting them to the next process step. Mechanically lapped silicon wafers (Dow-Corning, 100 ohm-cm p-type, cut perpendicular to the (111) direction) were chemically polished in a rotating beaker with a mixture of 1 part HF (48 pct), 2 parts glacial acetic acid, and 3 parts HNO3 (70 pct) by volume. This procedure yields a smooth surface with a faint "orange peel'' structure due to a "ripple" less than 20002i deep. Oxidation in steam or oxygen was carried out in an Electroglas tube furnace. Steam oxidations were always preceded and followed by a brief exposure to oxygen at the same temperattre. The thicknesses of the oxide films under 3000A were determined with a Rudolph Model 436-2003 ellipsometer,' whereas those over 3000A were measured using the VAMFO technique. In the present study, a solution of 300 g of N&F in 25 ml HF (48 pct) and 450 ml water was used to detect areas of increased chemical reactivity in the

Jan 1, 1965

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By F. V. Lenel, G. S. Ansell, E. C. Nelson

IRMANN&apos;S&apos; discovery that extrusions of fine alumi-num-flake powders possess remarkable high-temperature strengths has led to the production of a new class of engineering materials whose properties are derived from a fine dispersion of oxide particles in a metallic matrix. A fundamental study of such materials and elucidation of the mechanism whereby the oxide parti-

Jan 1, 1958

By J. Ralph Finlay

In latitude 4" S., about fifty miles from the Pacific, and in the amphitheater on the west flank of the Andes, which is drained by the river Tumbez, is the ancient town and mining district of Zaruma. The town is picturesque in the extreme, perched on a ridge 1800 feet high, between two lovely mountain rivers, looking out upon neighboring hills and valleys clothed in rich green, relieved by many hamlets roofed in red tiles, and, at greater distances on all sides, upon mountain slopes of gloomy forest crowned by the bare summits of the Andes. General Description. The gold-mines, discovered in 1549, mere worked extensively by the Spaniards in the 16th and 17th centuries, until their success was curtailed by the exhaustion of the oxidized surfaceores, and the uncovering of the refractory and hard ores underneath. The industry slowly declined until it was nearly or quite at a standstill in 1878, when an unfortunate English company, organized by Chilian promoters, acquired some of the best properties and began to work them. This company, after an extravagant début, relapsed into a struggle against poverty and mismanagement, and finally collapsed in 1894. In 1896 the English mines and many others, covering most of the district, were acquired by the South American co., formerly the South American Development Co., of New York. (See Figs. 1 and 2.) The vein-formation of Zaruma is extensive and complex, and the ores are somewhat refractory. In the immediate neighborhood of the gold-bearing veins the formation seems to be altogether volcanic, consisting of rather fine-grained holocrystalline diorite; but a few miles away, on either side, some gueisses and crystalline schists are to be found. About four miles south of the mines, and beyond some intervening granites, appear

Jan 1, 1901

By Henry M. Howe

Jan 1, 1909

Report of Secretary TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I have the honor to present the following report for the calendar year 1920 The activities which-seem to call for special com¬ment are THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published The Bound Volumes, as usual, contain all the papers in full and discussions thereof FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute&apos;s finances, since the dues of $12 per year are only 20 per cent greater than the members paid when the Institute was founded forty-nine years ago This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of\the national engineering societies has rendered the situation more difficult for us MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St Lours, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine

Jan 1, 1923

By E. R. Atkins, G. H. Smith

Results of laboratory tests are presented to show that lire value of "m", in the Archie expression dernlined by the shapes of the particles in the system. Tile value of m "the shape factor", is constant for a system of particles of a given shape for a range of F - + values. Applying this concept, one can predict F - + relationships for mixtures of particles with different shapes, and these predicted relationships are useful in electric log interpretation. It is suggested that an equation of the form 1/F -10mcan be used to describe the properties of natural formations containing varying amounts of sand and clay. From this work and values of "a" and "m" reported in the literature, it appears that in many cases rocks in the same geological horizon have a common primary porosity but contain varying amounts of a particular clay. It is concluded that the equation can be applied to a rock-water system only when values of "a" and "m" have been established for the particular system. INTRODUCTION The petroleum literature contains many reports of the results obtained by determining formation resistivity factor F and porosity + of rock samples from oil fields all over the world. The usual practice is to use data from a large number of samples from a number of fields to find an average relationship between F and +. Several such average relationships have been advanced. In the absence of data on a particular formation or field, it has been the practice to use the average relationships to give a rough approximation of the F - + relationship. The purpose of this paper is to report on basic relationships that exist between F and + for naturally occurring particles in water solutions. Other workers&apos; have found the same relationships apply to the diffusion of hydrogen through packed beds of dry particles. In the work discussed here, relationships for application to unconsolidated sands or shales containing mix- tures of particle shapes are derived. These relationships, developed for unconsolidated formations, may apply to consolidated formations. EXPERIMENTAL To evaluate F- relationships for unconsolidated rocks, the results of laboratory measurements on simple slurries of clay or sand will be used. Such laboratory studies are concerned with the electrical behavior of water-containing rocks. The wet rock constituents are electrically similar in slurries and in rocks. Archie2 defined formation resistivity factor as All resistance measurements were made using a 1,000-cycle impedance bridge with an oscilloscope as the null detector." The accuracy of this bridge was better than * 0.15 per cent. For the particular apparatus employed, no additional reactance was required to achieve balance for samples with resistances between

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue&apos; back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.&apos; Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962