Search Documents

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970

By H. C. H. Darley

The principal causes of unstable boreholes* have been known for many years. For example, in a paper published in 1938, Halbouty and Kaldenbachl listed nearly all the classes of troublesome shales that we know today. Much progress has been made since then, but we still have difficulty in identifying the cause of hole problems and consequently in selecting the right technique for combatting them. This subject was discussed at length by Kelly2 in a recent paper and much valuable information was provided. In the Shell Laboratory it was felt that there was a need for a better understanding of the basic mechanisms underlying the various forms of hole instability, and accordingly, a study was undertaken. This entailed reviewing the physics and chemistry of shales, developing tests for characterizing shales, and constructing a model to study borehole stability. Full simulation of underground conditions was not attempted; for example, we used reconstituted shale specimens, and often simple solutions or suspensions rather than practical drilling muds. Such procedures are necessary in order to establish mechanisms, but caution must be exercised in applying the results to the more complex conditions in the field. Part I — Compaction Swelling and Dispersion of Shales Compaction of Sediments Shales are formed by the compaction of sediments. Water is expressed as sediments are buried by subsequent layers, and the degree of compaction is proportional to the depth of burial, provided the water is able to escape easily to permeable formations. The younger sediments, when recovered at the surface, soften and disperse when mixed with water; the older shales have undergone diagenesis (alteration of the clay minerals, secondary cementation, etc.), and remain hard and unaffected by water. In this paper we shall apply the term "shale", as the drilling engineer does, to everything from clays, which are highly reactive to water, to completely lithified materials such as claystones and slates, which are completely inert. However, because these materials behave quite differently when encountered in the drilling well, it is desirable to develop a simple means of characterizing them. The feature that distinguishes the various shales is their dispersibility in water —soft clays disperse readily, harder shales disperse slowly when agitated, the lithified materials will not disperse at all unless milled. In the dispersibility test used in our study, a weighed amount of dry shale particles in the 12-to-100-mesh-size range was placed in a tube filled with distilled water and allowed to soak for 16 hours. The

Jan 1, 1970

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

Jan 1, 1962

By G. C. Stone

AS the term "hardness" is used with many different meanings, it should be understood that it here means resistance to deformation by compression. It was determined by measuring the pressure, in pounds per square inch, necessary to reduce by 20 per cent., the length of cylinders 1 in. (25 mm.) in diameter by 2.6 in. (66 mm.) long. The tests were made at Columbia University on an Olsen 400,000-lb. machine, the load being applied at a constant rate of speed 0.0319 in. per min. The results were obtained by Messrs. Rigg and Williams, and some of them were given in a paper read at the Sixteenth Annual Meeting of the American Society for Testing Materials, in June, 1913. The remainder of the results were obtained in subsequent experiments by the same authors. In all cases, the results given are the averages of three or more closely concordant tests. All of the spelters tested were of standard commercial grades and all were of compositions making them good deliveries. The accompanying table gives the results arranged in the order of increasing hardness:

Jan 1, 1919

By George Weaton

Two years ago the general features of the St. Joseph Lead Company&apos;s zinc-smelting process were described.1 At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtown smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the com-pany&apos;s mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; Si02, 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the concen-trate to a calcine of average composition (first 10 months of 1938) : Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; Si02, 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sul-phuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in. by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO2 to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1939

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME &apos;is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

Jan 1, 1966

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963&apos;s 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors&apos; earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"&apos; if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

Jan 1, 1970

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935