Search Documents

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

By H. G. Landua, Leah L. Naugle, H. H. Lowry

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Leah L. Naugle, H. H. Lowry, H. G. Landua

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By D. L. Harris, A. M. Gaudin

Observations were made of the distribution of mercaptan containing S35 between aqueous solution and mineral and between aqueous solution and the gaseous phase. Although equilibrium may not have been attained, adsorption of the reagent was shown to occur reasily from air or aqueous solution on sphalerite, zincite, and willem-ite and to correspond to flotation. Adsorption on quartz did not similarly occur. THE following results, presented here in condensed form,' were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report' of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr. Coarsely-crystallized sphalerite was handpicked, stage-crushed in the dry state, wet-screened on a 200-mesh sieve, and deslimed in water at about 5 microns. Further treatment consisted of a wash in dilute aqueous hydrogen peroxide, drying, removal of the dark-colored fraction in a Frantz magnetic separator, washing in very dilute hydrochloric acid, repeated washing in distilled and conductivity water, and drying. The last washings showed a conductivity equivalent to a few ppm NaC1, that is, much more than would be provided, theoretically, by a saturated ZnS solution. The material was stored dry in sealed bottles. Analyses were as follows: Zn, 62.3 pct; Fe, 0.43 pct; Cd, 0.44 pct; S, 31.2 pct; Mn, 0.001 pct. The specific surface (BET method) was 2000 cm2/g. Zincite from Franklin furnace of the New Jersey Zinc Co. was hand-picked, dry-crushed, wet-screened at 100 mesh, and deslimed at about 10 microns. After drying, the associated zinc, manganese, calcium, and silicate minerals were removed in a Frantz magnetic separator. The purified zincite was washed in distilled water and conductivity water to a conductance of less than 2 ppm equivalent NaC1, dried, and stored. Analyses were as follows: Zn, 75.1 pct; Fe, 0.9 pct; Mn, 2.78 pct. The specific surface (BET method) was 1740 cm 2/g. Willemite, also from Franklin furnace, was purified similarly. Analyses were as follows: Zn, 52.5 pct; Fe, 0.12 pct; SiO², 27.3 pct; loss on ignition, 0.13 pct. The specific surface was 1760 cm 2/g. Conductivity water (double-distilled) and demin-eralized-distilled water were used in most of the tests. The specific resistance was not less than 600, 000 ohms, and usually above 1,000,000. Radiosulphur-marked hexyl mercaptan (1-hexane thiol) was synthesized by Tracerlab, Inc., Boston. Two lots were secured several months apart. The last lot, consisting of about 0.5 g of the mercaptan, had a total activity of about 10 millicuries. Tracerlab Co. guaranteed only the activity; hence a quasi -vapor pressure determination (based upon an S analysis) of the mercaptan was made. The calculated value, 4.2 mm of mercury at 25.5' C, has been compared with that of a sample of Highest Purity 1-hexane thiol from Fisher Scientific Co. The latter had a vapor pressure of 4.5 mm of mercury at 2.5 C. Analytical Procedures The sample containing radiosulphur-marked mercaptan was oxidized to convert the mercaptan sulphur to sulphate, carrier barium sulphate being added to provide a suitable quantity of total barium sulphate in a filter cake. The precipitate was filtered and dried, and counting was carried out either in a streaming-gas (Q-gas) counter for high sensitivity or with an end-window G-M counter for convenience. The oxidized and precipitated mercaptan gave a radioactive count of 65 counts per minute per microgram in the end-window Geiger-Mueller counter and 1100 counts per minute per microgram in a Q-gas counter. For standardization of the mercaptan solution, 15 replicate analyses were made. The average deviation per measurement was about 1600 cpm in 65,000 cpm, the probable error in the mean being 275 cpm. It

Jan 1, 1955

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

By John L. Walter

A sintered compact of iron containing 0.007 vol fraction of glass , prepared 6). powder rnetullurgtcal lechniques, was rolled lo foil, 0.001 in. /hick. The foil sullrples were anneuled a1 650° to 850°C in hydrogen. Pri,narj recryslullization prodtnced large grains which Lc3ere highly elongnled in the rolling direclion und which had an unusual prgferred orientation. The glass parlicles assumed a stringerlike dispersiorz on working; llie slrinyers were parallel lo the rolling direction and to the long axis of the grains. The same unusual grain structure, preferred orientation, and stringerlike dispersion of purticles are found in heal-ily rolled and annealed foil of tungsten which has heen doped wilh small amounts of aluminum, silicon, and polassiutvt. Both the proper dispersion of the particles and severe working (reductions in excess of 98 pct) are necessary to produce the elongzcted grain structure. RECENTLY, the author reported on the origin of the elongated or "nonsag" grain structure in tungsten foil which was doped with aluminum, silicon, and potassium.' It was observed that particles, identified as mullite (Al6Si2Ol3), were present in the doped ingot (as sintered) and at all stages of processing from ingot to sheet or wire. It was shown that the particles, being plastic at tungsten working temperatures (up to 1550"C), underwent a "stringing out" parallel to the working di-direction. It was concluded that these strings of particles were responsible for the formation of the highly elongated interlocking grains observed in doped tungsten wire or sheet. To give further credence to this explanation of a long-observed but not understood phenomenon, it was decided to design a new system, one which was analogous to the doped-tungsten system. Thus, a bcc metal, iron, was chosen to be doped with glass which would be plastic at reasonable working temperatures for iron. The glass chosen was a #0080 Corning lime glass which melts at about 810°C. This is approximately the same fraction of the melting point of iron (0.6) as the melting temperature of mullite is of tungsten. It will be shown that all the observed unusual features of the doped tungsten are duplicated in the glass. doped iron, even to the preferred orientation of the grains in the recrystallized sheet. In the tungsten sheet the preferred orientation consists of two components, (1i3)(691) and (013)(362), neither of which has been observed as a component in textures of primary recrystallized bcc metals. EXPERIMENTAL PROCEDURE The glass, in the form of fine powder, was added to high-purity electrolytic iron powder and mixed dry. The particular composition chosen was 0.007 vol fraction of glass. After mixing, the powder was mechanically pressed to a disk 0.5 in. diam and 0.15 in. thick at a pressure of 5000 psi. The pellet was sintered, in pure dry hydrogen, for 2 hr at 8 50°C. The sintered pellet was then heated to 750°C and rolled to 50 pct reduction of thickness in two passes, with reheating between passes. The rolling temperature was then reduced to 600°C and the slab was rolled to a thickness of 0.050 in. Rolling to 0.010 in. was accomplished in several passes at 300°C. Final reductions to 0.003 and 0.001 in. were taken at room temperature. This rolling temperature schedule was similar, in terms of the fraction of the melting point, to that used in the rolling of the doped tungsten. The total reduction of thickness was in excess of 99 pct. Samples of the rolled foil were lightly electro-polished and annealed for 1 to 6 hr at temperatures of 650" to 85O°C in hydrogen. Samples for transmission electron microscopy were thinned on a Disa Electropol using AC-1 electrolyte.

Jan 1, 1968

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By E. F. Bradley, R. I. Jaffee, H. R. Ogden, E. S. Bartlett, D. N. Williams

The mechanical properties of solid-solution-strengthened columbium alloys have been assessed as a function of alloying additions. Studies included the effects of tungsten, tantalum, molybdenum, and vanadium. Elevated temperature fabrication was required at alloying levels above about 15 pct W or 10 pct Mo. Tungsten, molybdenum, and vanadium additions increase tensile strength at room temperature and 2200°F, but tantalum additions exert little strengthening. Similarly, tungsten, molybdenum, and probably vanadium additions increase the ductile-to-brittle transition temperature, and tantalum additions decrease this parameter. The 2200°F stress-rupture strength is increased by tungsten and molybdenum additions; with 20 to 25 at. pct additions, 100-hr rupture strengths of 30,000 psi are obtainable. Small vanadium additions exhibit mild stress-rupture strengthening, and tantalum additions are innocuous. At 2500°F, tungsten additions retain stress-rutpure strengthening capability, but molybdenum additions are much less effective. Tantalum additions augment the stress-rupture strengthening of tungsten plus molybdenum additions at 2500°F. Of the refractory metals, columbium possesses specific potential for structural use in the temperature range from 2000" to about 2500°F. Desirable features of columbium are its good low-temperature ductility, ease of fabrication, oxidation mechanics (lack of a volatile oxide at moderate temperatures), good availability and reserves, and relatively low density. However, alloying is required to provide attractive strength at elevated temperatures. Published information concerning alloying be- havior of columbium relative to mechanical properties is sketchy, particularly in consideration for long-time applications at temperatures in excess of 2000°F. Only a few stress-rupture data at temperatures from 2000" to 2500°F have been reported;'-' these are too meager to allow rationalization of the effects of various alloying additions on creep or stress-rupture properties. Additional published data do, however, give some insight toward understanding of systematic alloying behavior for columbium relative to low-temperature strength4-' and ductility,' and elevated temperature tensile behavior.4,6 This paper is intended to augment previous knowledge, and to promote understanding of the alloying behavior of columbium for long-time structural service at elevated temperature. BASIC CONSIDERATIONS Solid-solution strengthening is recognized to be of prime importance in improving strength in columbium-base alloys. Other strengthening mechanisms may be (and are, in current alloys) used to augment solid-solution strengthening. As strengthening results primarily from lattice distortion, the strengthening effectiveness per atom depends upon atomic size mismatch between solvent and solute. Another factor in this regard is conformance to ideal solution behavior in the solid solution. Thus, for example, despite appreciable differences in the degree of mismatch between tungsten (5 pct), molybdenum (5 1/2 pct), and vanadium (7 1/2 pct) in solution in columbium, all are about equally effective in straining the columbium lattice at room temperature.'-' Similarly, tantalum additions do not strain the columbium lattice, and little strengthening is expected. Size effects being equal, maximum solution strengthening at high temperatures is anticipated to result from the addition of elements that increase the melting temperature of columbium. This expectation is based on an increase in the electronic bonding forces exhibited in the transition metal series as electronic structures approach those of the Group Vl metals. Of the metals that exhibit ex-

Jan 1, 1963

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans' calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By G. H. Ruggles

POPULAR opinion, as it might be termed, has always been of the trend that a flotation reagent added to the ball mill during grinding would be more thoroughly mixed with the pulp and for that reason more effective in the production of low tailing. That there are other effects, inimical to good flotation, when using so-called chemical reagents, is brought out by the series of tests outlined in Table 2. It was defi-nitely proved that if either the T. T. mixture (20 per cent thiocarbanalid-80 per cent orthotoluidin) or po-tassium xanthate were added to the ball mill the result-ing flotation concentrate would be lower in copper and higher in insoluble than the concentrate produced by adding these same reagents without the ball mill cir-cuit. With the T. T. mixture four sets of tests were made. The screen analyses of the flotation feed show that there was very little difference in the original grind-ing. When the T. T. mixture was added to the head of the flotation machine the flotation concentrate had a little over 61 per cent solids -200 mesh. If the mix-ture was put into the ball mill the flotation concentrate had but 40.7 per cent of the solids -200 mesh for one set of tests, and 49.0 per cent for the other set. With the mixture at the head of flotation the total concen-trate was high in copper (34.715 and 36.525 per cent) and low in insoluble (13.20 and 11.61 per cent). The assay of the concentrate when the T. T. mixture was introduced into the ball mill was what might be termed low in copper (29.389 and 30.833 per cent). In one of these 'sets of tests (periods 8 to 11, third column) the insoluble was high, 16.81 per cent. The other run (peri-ods 12 to 15, fourth column) for some unknown reason shows a low insoluble, 12.72 per cent. With similar grinding the addition of potassium xan-thate to flotation produced a concentrate having 62.8 per cent -200 mesh, whereas with the potassium xanthate added to the ball mill the flotation concentrate was very coarse, only 36.4 per cent passing 200 mesh. The difference in the total assay of the concentrate is remarkable ; 35.847 per cent copper when the xanthate went to flotation and 30.44 per cent copper when the xanthate was added to the ball mill; insoluble, 10.94 per cent in the former instance, as 22.15 per cent in the latter.

Jan 8, 1927

By G. M. Schwartz, J. N. Gundersen

John W. Gruner (Professor Emeritus, College of Science, Literature, and the Arts, Dept. of Geology, University of Minnesota, Minneapolis) — It is surprising that two men as well acquainted with the taconite rocks of the Mesabi District as Drs. J. N. Gundersen and G. M. Schwartz should have concluded that the taconite of the Eastern Mesabi before the intrusion of the Duluth gabbro consisted largely of quartz and magnetite. These minerals were "locally reconstituted" into "a wide variety of silicate mineral assemblages" by the gabbro. It is well known, of course, that the silicate mineralogy of the Eastern Mesabi ('about 14 miles in length) is quite different from that of the Main Mesabi which is over 60 miles long. The change from one to the other is abrupt and cannot be attributed to any other cause than the thermal effects of the gabbro. Are we to assume or believe that the taconite of the Eastern Mesabi was radically different from that of the Main range before the gabbro metamorphosed it?

Jan 1, 1962

By H. H. Campbell

The following paper deals almost exclusively with the results of practice at the works of the Pennsylvania Steel Company at Steelton, Pa. From the records of the furnaces at this plant, both acid and basic, large and small, are drawn the data for the various demon strations, and on a long and intimate experience with their opera tions are founded many theories and generalizations. It may seem that universal laws should not be built upon a basis so restricted ; but in reality the condition is the strongest guarantee of validity. Each table investigates some- certain variable, and by virtue of the common origin of the factors, we have good ground for assuming the corresponding agents to be equal. The examples may or may not be instances of good practice, and may be open to criticism if regarded solely as exponents of • metallurgical success. But it must be remembered that the lists are not made up of selected specimens, nor are they chosen to show su perior results; they are gathered to investigate, by strict scientific methods, the formula? of the operation. In such work no untoward results should be eliminated, save those which bear upon their face the stamp of experimental error. If the worst members be omitted, then the best must also be omitted. Only by using every available case can an honest attempt be made to deduce a true average. It is recog nized, however, that with the most careful selection it is difficult, if not impossible, to collect data representing universal conditions. In each table the records tell of a special practice, and all conclusions drawn from them are true only within the limits between which the equations have been integrated. Not assuming the prerogative of speaking for American melters in all the opinions herein expressed, nor acting as a camera in por traying an ephemeral state of national metallurgical development,

Jan 1, 1894

By Herbert Hoover

This paper is in the nature of a rough preliminary report on the progress that has been made in the application of the mass spectrometer to various problems arising in the petroleum industry. A few years ago the authors considered a number of the problems that were arising in the qualitative and quantitative measurement of small amounts of hydrocarbons. The methods available of making analyses by chemical techniques appeared to leave much room for improvement. Without going into the reasons at this point, attention was turned to the possibility of employing physical instead of chemical methods of accomplish-ing the desired results. A preliminary investigation disclosed that the mass spectrometer presented a possibility of solving many problems which could not easily be accomplished by other methods. Work was begun in developing the necessary apparatus and technique. A great deal of encouragement and many valuable suggestions were received from Dr. Robert A. Millikan, Dr. W. R. Smythe, and Dr. W. N. Lacey, of the California Institute of Technology, and from Dr. E. 0. Lawrence, who recently received the Nobel Prize, of the University of California. The authors particularly wish to acknowl-edge the very great willingness of these out-standing scientists to be helpful in solving many of the problems that were involved. So far as the authors are aware, this was the first application of the mass spectrometer to commercial work. The results were considerably better than had at first been anticipated. Briefly, it is pos-sible to run a qualitative and quantitative analysis of an unknown mixture of hydro-carbon gases, with an accuracy of better than plus or minus 5 per cent of each of the various constituents. An exceedingly high degree of sensitivity has been obtained, and a relatively short time is required to com-plete an analysis. Furthermore, it is un-necessary to separate a mixture of gases into its various components in order to complete the analysis.

Jan 1, 1940

By E. J. Harris

Mathematical solutions to complex mine ventilation problems are possible, but often the airway network is so complex that the mathematical solution becomes tedious and impractical. A fluid network analyzer, designed and built for analyzing mine ventilation problems has been in service at the Bureau of Mines' Pittsburgh station for approximately nine years. Using this analogue as a model, the mine ventilation network is simulated electrically by a combination of series and parallel circruits laid out to conform with actual mine airways. A tungsten filament lamp, referred to as a Fluistor, is used to simulate mine airway resistance. With the analogue ventilation model established, voltages of the proper amplitude to represent ventilating pressures are impressed across the circuit at points where mine fans and airshafts are located. Comparison of mathematical solutions of complex systems against analogue results showed a maximum variance of 3% for pressures and 2% for quantities. An electrical fluid network analyzer, designed and built especially for analyzing mine ventilation distribution problems, has been in service at the Bureau of Mines, Pittsburgh, for approximately nine years. It is a nonlinear, low voltage, fluid network analyzer of the type developed by the late Malcolm S. McIlroy, Professor of Electrical Engineering, Cornell University, who cooperated with G. E. McElroy, of the Bureau of Mines, in adapting the instrument to mine ventilation systems. Several modifications have been made since the original installation, but a considerable part of this paper is drawn from G. E. McElroy's original description of the analogue.' The analysis of water or gas distribution systems2,3 led to the development of this type of network analyzer. Several similar units are now employed by utility companies for this purpose; however, the Bureau of Mines unit is the only one designed specifically for mine airflow problems. Other airflow analogues employing a similar principle have been used at the Central Research Station of the Netherlands State Mines,4 in England,5 and in South Africa.6 Information on these devices indicated they were somewhat inflexible because commercial lamps with a sufficient range of resistance are difficult to obtain. Computers for mine ventilation analysis have been developed in Germany which instead of lamps use a variable resistance to adjust for turbulent flow laws. These units are expensive, but excellent results have been reported in their application. THE ANALYZER Theory of Application: As airflow generally follows the law of turbulent fluid flow, resistance to flow is nonlinear; consequently, the problem has been to find a nonlinear resistance element of suitable range that can be used for electrically simulated airflow. Tungsten filament lamps operated on alternating or direct current approximate the square-law resistance characteristics of mine airflow over a large range below maximum or rated voltage; that is, the voltage drop varies approximately as the square of the current. Consequently, the heart of the network analyzer is a nonlinear resistor known as a Fluistor, which is simply a custom-made low voltage, tungsten filament lamp that is available in a progressive series of relative resistance values ranging from 0.05 to 500 in nominal 5% steps. However, variations in manufacturing large groups result in differences of 1 to 3%, but series arrangements required for high-loss branches can be matched within about 1%. Utilizing a combination of Fluistors and load circuits, the mine ventilation system is duplicated electrically. Intake load circuits are connected from power intake to primary points of the circuit network; segments of unregulated flow along intakes and returns are represented by Fluistors, regulated splits and leakage paths are represented by load circuits and Fluistors of proper capacity; and mine exhausts are connected to ground from the last point of the network to complete the circuit. For the special purpose of representing booster fans or natural draft conditions, boosters or separate source circuits are provided that can be inserted between any two points of a network to increase voltage to the required value. Physical Layout: The analyzer consists of three 42

Jan 1, 1963

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per 'C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons' interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3' All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.'s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.'s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967