Search Documents

By C. M. Tucker, Kent R. Van Horn, W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1‡, Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metallographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-fish intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. METALLOGRAPHIC INVESTIGATION A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500° to 1600° C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively

Jan 1, 1935

By C. S. Barrett

IT has been observed that deformation in iron takes place by slip on {110} + {112} + {123} planes1,2 but in silicon ferrite with low deforma-tion temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to {110} planes, at least with small amounts of deformation. The purpose of the present inves-tigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Inci-dental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture. (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which [110] directions of the grains lie along tile direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direc-tion as all axis 3-9. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45° and 50° or 60° for iron5,6,9 and is usually in the neighborhood of 50° for mild steel6,7,8. The range of this deviation is a function of the percentage of total reduction 8, 10. Post' reported that it decreases with increasing percentage reduction, but apparently he .studied only the surface material, which Gensamer and Mehl7 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass.

Jan 1, 1937

[Admissions: Aurel E. Smith, Chairman Edmond F. Egan Lawrence S. Fennell John S. Fuller Howard J. Ritts, Jr. Gene E. Roark Kenneth W. Robbins Ben M. Gottlieb Advertising: Bernard F. Klein, Chairman Henry N. Lyle R. E. Howard H. M. Krause, Jr. Mrs. Evelyn R. Robertson]

Jan 1, 1961

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

By A. A. Smith, J. S. Smart

THE controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modem copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range 0 to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously.1-2-3 Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,1, 2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of 3/8-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 850°C. from a surface scale. Test wires were drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at o.3125, 0.257, o.204 and o.162 in., and a final cold reduction of 95 per cent t0 0.081 in. Oxygen-bearing slugs made by remelting were hot-rolled to 5/16 in., drawn to 0.162 in., annealed for 30 min. at 600°C. and cold-drawn 95 per cent to 0.081inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 5/16-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700° to 800°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals were of one hour duration followed by a rapid quench in 10 per cent H2SO4. EFFECT OF PHOSPHORUS The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1945

By G. Borelius

ABOUT the turn of the century, Gibbs' thermo-dynamic theory of heterogeneous equilibrium, on the one hand, and the experimental methods of thermal and microscopic analysis, on the other, gave to the physical metallurgist his first scientific tool, the equilibrium diagram. The classical equilibrium diagram of a binary alloy system shows the boundaries between ranges of homogeneous and heterogeneous equilibrium in their dependence of concentration and temperature. A homogeneous solid sohtion which on cooling passes such a boundary is assumed to precipitate, forming a mixture of two phases with different concentrations. The equilibriunl diagram and the equilibrium theory, however, give no information about the time scheme of the process or the intermediate states passed during precipitation. For this reason it satisfies neither the practical need of the metallurgist nor the curiosity of the physicist. As a matter of fact, in the heat treatment of alloys for technical use the objective very seldom is the equilibrium state. Thus good mechanical properties of construction material are connected, for the most part, with some intermediate state. As these intermediate states are thermodynamically unstable, there is, from a theoretical point of view, always to be expected a decay of the good properties with time; and it is a matter also of practical interest to know whether this natural life time of a material is of the order of, say, ten or thousands of years. Thus, for many reasons, there is a current demand to complete our knowledge of equilibrium through knowledge of the kinetics of the precipitation phenomena. From the point of view of the physicist, the most interesting question in this case is whether there are any general laws governing the kinetics. According to a generally accepted view, precipitation is ruled by two more or less independent phenomena, the formation of nuclei of a new phase and the growth of these nuclei. It is also commonly accepted that there is a tendency for the velocity of growth to increase with increasing temperature because of the increasing mobility of the atoms. There is also a tendency for the velocity of growth to decrease in the neighborhood of the two-phase boundaries. So far, however, very little is known quantitatively about this fundamental phenomenon in the case of solid metallic systems. In our laboratory attention has been directed especially toward the nucleation phenomena, and a series of measurements have been carried out with the guidance of a work- ing hypothesis (based on experiences from previous work on order-disorder transformations in alloys) about the influence on the nucleation of thermo-dynamic potential barriers. However, before discussing the experiments, the theoretical ideas will be considered. In a binary solid solution the arrangement of atoms on the lattice points approaches with increasing temperature a state of full randomness, as illustrated by the ball model of Fig. 1, that might represent a [111] plane of a face-centered alloy with 30 pct "black" and 70 pct "white" atoms. In reality the atoms are changing places continually with their neighbors so that the picture should rightly have been a moving one. On account of this thermal motion the concentration of black atoms within a certain group of, say, a hundred or a thousand lattice points fluctuates with time around the bulk concentration of 30 pct in a manner governed by statistical laws. With decreasing temperature two independent changes in this state grow more and more important. First, the mobility of the atoms decreases, and second, the forces between the atoms will have an increased influence on the fluctuations. In alloys with a tendency for precipitation, which are the concern of this lecture, the distribution function of concentration fluctuations will broaden, so that the relative probability of great local variations from the bulk concentration increases. Fig. 2 gives an example of such a fluctuation. When the alloy is supercooled below the solubility limit into the range of two-phase equilibrium, the fluctuations will now and then at some point give rise to a state that resembles the equilibrium state and thus will form a stable nucleus that is capable of growing by diffusion processes. In discussions with colleagues and in the literature, I have often encountered the idea that three or four atoms of the dissolved metal could form a nucleus of the new phase. A look at the ball model might be enough to indicate that this cannot be true. If it were true, there should be nothing but nuclei, whereas we know from experiment that nucleation must be a rather rare occurrence. In fact we have, as will be mentioned later, certain reasons to believe that the nuclei are formed by fluctuations containing some hundreds of atoms, which should be the order of the number of black balls in the fluctuating group of the figure, if it were extended into three dimensions. As a working hypothesis we have assumed that the fluctuations producing nuclei, though large and rare, still are ruled by the distribution laws of fluctuations of the supercooled solid solution in its initial state. Thus the probability of nucleation will be connected to the thermodynamic properties of the solid

Jan 1, 1952

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By Joseph E. Pouge

For the purposes of this analysis it is assumed that the petroleum industry has undergone a basic economic change whereby the degree of competition present in its operation is reduced by the collective control of production brought about by statme-directed proration. Formerly freely competitive in all its parts, the industry is now fully competitive only in its marketing, its manufacturing and transportation, its search for new oil supplies, its drilling operations (with some qualifications), and its capital movements. The practical problem before the industry in its new status is the maintenance of equilibrium, with planned control of crude-oil production (proration) substituted for competition and price as the regulatory mechanism at one point in the supply-demand system. It is further assumed that proration has become so firmly established in the legal and operating framework of the business that it may be looked upon as an institution. The purpose of this paper is to call attention to the effect of unregulated drilling upon the orderly functioning of proration. Economic Structure of Petroleum Industry The economic structure of the petroleum industry, under the current form of proration, may be visualized, in simplified form, as shown in Fig. 1. This diagram is designed to indicate the existing mechanism whereby supply and demand are equated. Demand is created largely by conditions external to the oil business, whereas supply is conditioned by a series of stages incidental to the discovery, development and production of a resource. The time elements involved in changes in demand and supply are of an entirely different order, the demand factor being much more flexible and "quicker" than the supply factors. It should be observed, also, that the position of price, formerly between "demand" and "supply," has been moved to a sidewise location where it still affects demand but influences current supply only through its bearing upon proration, drilling and search. Proration has been substituted for price as a throttle at the well head, but at this point only. The mechanism now works in this fashion: a declining price stimulates demand and the

Jan 1, 1936

By Joseph E. Pouge

For the purposes of this analysis it is assumed that the petroleum industry has undergone a basic economic change whereby the degree of competition present in its operation is reduced by the collective control of production brought about by statme-directed proration. Formerly freely competitive in all its parts, the industry is now fully competitive only in its marketing, its manufacturing and transportation, its search for new oil supplies, its drilling operations (with some qualifications), and its capital movements. The practical problem before the industry in its new status is the maintenance of equilibrium, with planned control of crude-oil production (proration) substituted for competition and price as the regulatory mechanism at one point in the supply-demand system. It is further assumed that proration has become so firmly established in the legal and operating framework of the business that it may be looked upon as an institution. The purpose of this paper is to call attention to the effect of unregulated drilling upon the orderly functioning of proration. Economic Structure of Petroleum Industry The economic structure of the petroleum industry, under the current form of proration, may be visualized, in simplified form, as shown in Fig. 1. This diagram is designed to indicate the existing mechanism whereby supply and demand are equated. Demand is created largely by conditions external to the oil business, whereas supply is conditioned by a series of stages incidental to the discovery, development and production of a resource. The time elements involved in changes in demand and supply are of an entirely different order, the demand factor being much more flexible and "quicker" than the supply factors. It should be observed, also, that the position of price, formerly between "demand" and "supply," has been moved to a sidewise location where it still affects demand but influences current supply only through its bearing upon proration, drilling and search. Proration has been substituted for price as a throttle at the well head, but at this point only. The mechanism now works in this fashion: a declining price stimulates demand and the

Jan 1, 1936

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By J. C. Motz

Introduction The variations in crushing plant design seen during the past 30 years provide a valuable source of information and experience from which one can select the optimum arrangement for a specific requirement. The purpose of this paper is to examine some specific equipment configurations as they relate to operating efficiency, plant availability and final product size in the form of mill feed. Due to the varied ore properties, physical space limitations, size of ore body and financial resources, there is no single crushing or grinding flowsheet that is best. Since energy costs have risen dramatically during the recent past, it became obvious that significant savings are possible by selecting equipment and a circuit which offers low power requirements balanced with low wear metal and installed equipment costs. Relatively clear and measurable are the metal and maintenance costs and the ever increasing cost of energy. Metal costs in the form of crusher liners have not quite doubled in the last 20 years, while power costs have increased by a factor of four or five, depending on the region considered. Estimates made only a few years ago on the increased cost of energy are obsolete in view of the recent unstable conditions. Since power is therefore becoming the largest cost area, it behooves us to investigate potential cost saving methods in the form of lowering the KWH/Ton of crude. Crushing To reduce run-of-mine to mill feed requires reduction in a series of stages. The physical size and power requirements of a crusher capable of reducing hard rock vary depending on the application. Extended experience in most crushing plants show that a minus 19MM (3/4 in.) rod mill feed can be and is being produced in three stages of crushing. In the majority of cases, the last crushing stage is closed circuited using anywhere from 19MM (3/4 in.) to 14MM (9/16 in.) slotted openings on the sizing deck. In some copper concentrators, the mill feed is all passing 13MM (1/2 in.) using three stages of crushing and 14MM (9/16 in.) square openings on the closed circuit screens. It was felt by some that crushing to this fine size is only possible if the ore is friable and is relatively soft in comparison to the harder ores. Our results show that some of the copper ores are as hard as taconite and are crush-

Jan 1, 1982

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By E. C. Lee

THE safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. This fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossment in earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual-cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 10, 1917

By L. L. Melton, D. L. Lord, B. W. Hulsey

A mathematical model d1.20p/4L = A(8v)8 derived from the Blasius equation is proposed to be applicable to turbulent flow through straight cylindrical pipe for time-independent fluids which produce a diameter family of straight parallel lines on a log (dp/4L) vs log (8v/d) plot or stress-flow diagram. Such a correlation should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable frictional pressure reductions. The Newtonian diameter exponent value 1.20 is shown to be empirically valid for turbulent non-Newtonian flow by application of numerical analysis methods. Multiple regression analysis is applied to a logarithmic linearization of the proposed model. An improved data fit results from further linearization achieved by taking linear terms from a generalized Taylor's series expansion about the multiple regression coefficients. Extensive experimental data obtained in five pipe diameters with water, sodium carboxymethyl-celIulose solutions, guar gum solutions, bentonite clay suspensions and calcium carbonate slurries are presented. Except for calcium carbonate slurries, which were investigated rather than time-dependent cement slurries, the fluids studied contain drilling or fracturing fluid additives. The behavior exhibited by these fluids is considered typical of most fluids encountered in drilling, cementing and fracturing operations. INTRODUCTION Considerable difficulties have been encountered in predicting turbulent flow pressure drops produced by non-Newtonian fluids flowing through straight cylindrical pipe. Correlations previously presented require extensive experimental data which represent several pipe diameters and a wide flow rate range to estimate the necessary scale-up parameters.l-7 One must implement either elaborate experimental apparatus or spend considerable time and effort to gather these data. Presented here is a correlation method which should minimize the experimental effort and data analysis normally required by utilizing flow data taken with only one pipe diameter. Turbulent flow data (up-stream and down-stream pressure and volumetric flow rates) were collected for five pipe diameters through operation of a small pipeline system having an electronic data acquisition and digitizing system. A mathematical model derived from the Blasius equation was utilized to describe the functional relationship between pressure drop and the two independent variables, diameter and average flow velocity. A correlation, which should produce a valid single-pipe scale-up, resulted from a computer-implemented statistical and numerical data analysis for several time-independent non-Newtonian fluids.

By W. F. Durfee

The apparatus described in this paper was designed by the writer, in the year 1869, for use in the laboratory of the " American Silver Steel Works," at Bridgeport, Conn., where only the vacuum-pump was erected ; but on two subsequent occasions I have had the combined vacuum-pump and table-blowpipe constructed as represented in the drawings, in which Fig. 1 is a general elevation of the apparatus, the air-chamber being sectioned vertically; Fig. 2, a plan of the air-chamber; Fig. 3, a vertical sectiotnal elevation of the vacuum-pump, the section being on line C L), of Fig. 4, which is a horizontal section on line A B, of Fig. 3. The vacuum-pump is constructed of copper, and consists of a vacuum-chamber, E, supported upon the upper expanded end of a vertical pipe, Q. The vacuum-chamber is provided with four nozzles, C, F, I, D (Fig. 4), two of which are shown in section at A, B (Fig. 3). Passing vertically through the centre of the vacuum-chamber E, is seen the water-supply pipe P, whose lower extremity incloses an internal pipe p, which is supported, and placed in communication with the vacuum-chamber E, by means of the two elliptical nozzles n, n. The upper part of the pipe p is closed by a conical cap, and its lower end is in the same plane with the extremity of the watersupply pipe P, within which it is placed. The relative sizes of the pipes P and p are such that an annular adjutage, one-sixteenth of an inch in thickness, is formed between their lower extremities, through which the water from the supplypipe P passes into the pipe &, drawing any air that may be in the

Jan 1, 1885

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By AIME AIME

Adjustable Pyrometer-Stand. By L. W. BAHNEY, xxxvii, 33. Agency of Manganese in the Superficial Alteration and Secondary Enrichment of Gold-Deposits in the United States. By WILLIAM H. EMMONS, xlvi, 767. Application of Descriptive Geometry to Mining-Problems. By JOSEPH W. ROE, xxxix, 173. ARNOLD, C. EVERARD. The Giroux Shaft at Kimberly, Nev., xlii, 461. BAHNEY, L. W. An Adjustable Pyrometer-Stand, xxxvii, 33. BALL, SYDNEY H., and SHALER, MILLARD K. Mining-Conditions in the Belgian Congo, xxxix, 253. BEALS, ROGER L., and TWEEDY, GEORGE A. Cyanide-Plant and Practice at the Minas del Tajo, Rosario, Sinaloa, Mexico, xxxviii, 123.

Dec 1, 1910