Search Documents

By AIME AIME

THE annual meeting of the A.I.M.E. was fittingly closed with a joint meeting of the Metropolitan sections of the four National societies on Feb. 18, at which this subject was adequately discussed by leading engineers before an audience that completely filled the Engineering Auditorium. The large amount of publicity that has been given the Diesel electric loco- motive, and the often garbled reports of its performance and possibilities that have been circulated, makes it particularly fitting that the facts should be given the profession as determined by those who have aided in developing and operating this latest form of prime- mover in railroad operation. C. A. Stein, general manager of the Central R. R. of New Jersey, opened the meeting with a discussion of the problem of electrification, and the relation of the short haul, switching, and terminal service to heavy electrification. Referring directly to the problem of the Central R. R. of New Jersey, some subtitution for the steam locomotive is necessary within the city limits of New York because of local ordinances against the smoke nuisance. While the improvement in the design of the steam locomotive has been marked-the efiiency today is over fifty times that of the locomotive of 100 years ago-it has now probably reached the point of maximum perfection. If anything, it is open to the criticism of having Coo many appliances to get out of

Jan 1, 1926

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By L. D. Keller

The application of hydraulic concentration to large scale operations has been effectively accomplished by the use of the SiphonSizer. Operation has been simple, automatic and essentially trouble free. The use of the primary desliming SiphonSizer on magnetic taconites has shown an improvement in grade of concentrate and an increase in recovery over conventional hydroseparators. Magnetic concentrates have been further deslimed and upgraded in SiphonSizers by floating a coarse middling product away from the heavier concentrate. The application of the Siphon-sizer to closed circuit grinding has met with only partial success to date. Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to equipment using a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units varying in size from a 16-ft diam circular unit to a 25x100-ft rectangular unit are currently in operation on magnetic taconites. Additional units up to 38 ft diam are under construction. Depending upon the application in the flowsheet, upgrading varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to remove economically as much silica as possible may not be fully appreciated. Perhaps some figures pertaining to transportation costs will underscore this important process. If the silica content of the concentrate from a 10,000,000 ton per year plant could be reduced by I%, a savings in boat freight, at $2.00 per ton, would amount to $200,000 annually! THE SlPHONSlZER The SiphonSizer, as illustrated in Figs. lA, 1B and 2, is a hydraulic classifier in which the hydraulic water is distributed uniformly across the bottom of the vessel by means of a system of headers (1 and 2), jet pipes (3), and nozzles (4). The depth of the teeter bed is automatically maintained by the siphon-float assembly. The feed is introduced through a feed well (5) and separated into two fractions by the effects of rising water and the density of the teetered bed. The magnetite fraction is discharged by the siphon (12) while the fine slime and light middling overflow a peripheral weir (9) to the overflow launder (6). The bed depth is controlled automatically by float valves (7), which are responsive to changes in the height of clear water supported in the superelevation tubes (8) by the density of the teetered bed. On top of the float (7) is a needle valve (10) which permits

Jan 1, 1963

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."' The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald' presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland' discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.' The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By E. H. Boswell, E. M. Cushing

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gpd) of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1600 trillion gal. Ground water having a dissolved-solids content of less than 500 ppm is generally available at depths of less than 1000 ft, and water having a dissolved-solids content of less than 1000 ppm is available in some places to depths of more than 3000 ft. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-ft (about 45,000 mgd). An additional 375 million acre-ft (about 340,000 mgd), which originated outside the region, leaves the region as streamflow during an average year. Some streams have considerable flow during periods of no precipitation and the water during these periods generally has a low dissolved-solids content. Large quantities of water from streams and waterbearing sands (aquifers) are available in the Mississippi embayment east of the Mississippi River. Most of the region is underlain by aquifer systems that will yield large quantities of water to wells, making ground water the most readily available source of fresh water. About 90% of the water used in the region is obtained from wells. Streams have been used primarily to dispose of, and dilute, wastes that have been dumped into them. The Mississippi, Ohio and Tennessee rivers, and the lower parts of the Tombigee and Yazoo rivers also serve as a means of transportation. This nominally water-rich region receives from 48 to 56 in. of precipitation in average years and is crossed by several large rivers. The largest, the Mississippi River, is the western boundary of the region discussed in this paper. The economy of the region is basically agricultural, but industry has become increasingly important since World War 11. The diversification and mechanization of agriculture have resulted in a surplus of manpower, most of which is being absorbed by the expansion of industry. Further industrial expansion probably will occur because of the available manpower, natural resources and economical transportation. Increasing demands on available water supplies will be made and the future economic growth of the region will be largely dependent upon wise utilization and management of the water resources.

Jan 1, 1969

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By L. F. Stutzman, George Thodos

A new graphical method, which is a modification of that proposed by Buckley and Leverett', is presented for the determination of the displacing fluid saturation at breakthrough for frontal drive mechanisms. This method is applicable to all types of fluids, which may be either soluble or insoluble in the oil at reservoir and injection conditions. This adaptation has unique advantages in handling problems in which either liquids or gases are the displacing fluids. INTRODUCTION In the displacement of oil from a reservoir with water or gas injected into the formation or by the expansion of a gas cap, the determination of breakthrough or flood advance is important to define the initial and subordinate phases of the operation. Thus, the determination of the displacing fluid saturation at breakthrough is fundamental to the establishment of over-all reservoir production. Methods for analyzing this saturation and for calculating production rates have been previously reported1,'*".". All of these methods utilize the rate equation for linear flow developed by Buckley and Leverett1. xs = QT - Qn/A? (?fu/?Su) .....(1) Sp where f, represents the volumetric fraction of displacing fluid in the total flowing fluid within the reservoir as is defined by: fo = 1/1+ ku/kd µn/µn .......(2) Since the time, ?, necessary for the flood front to travel distance ?X is unknown, Eq. 1 cannot be solved directly for the determination of the breakthrough point. Therefore, it becomes necessary to solve Eq. 1 simultaneously with an equation representing a fluid bal-ance on the reservoir behind the flood front. To develop such a fluid balance equation, it has been assumed that the fluid composition is uniform in the reservoir behind the flood front. Based upon this assumption, the follow-ing equation can be derived from a material balance on the displacing fluid: x = (?X) s Dx ? x=0 [ Snx - Sn1 ] dx = QT - Qn/A? It is readily observed that the displacing fluid satura-tion behind the flood front, Snx, may be determined through the simultaneous application of Eqs. 1 and 3. Although the approach may vary, this objective re-mains the same for all of the previously mentioned graphical or analytical methods. After Sox is determined, it is then possible to calculate the gas-oil and/or water-oil ratios and the rates during the initial and subordinate phases of production, and thereby define the production history of the reservoir. In this presentation only the de-termination of Snx is considered, and the reader is re-ferred to the several texts in reservoir engineering2,4,5 for a complete discussion on the methods for establish-ing the production history of a reservoir. PROPOSED METHOD FOR DETERMINING Snx Since at any time the quantity, QT - Qn/A? is a constant, Eq. 1 may be expressed in differential form as follows: dxsn = QT - Qn/A? d (? fn/? Sn) sn .....(4) Eq. 4 may be substituted directly into Eq. 3 to obtain: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = QT - Qn/A? ...............(5) Eq. 5 simplifies to the expression: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = 1 ....(6)

Jan 1, 1958

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By Ott F. Heizer

The mines and the mill of the Nevada-Massachusetts Co. are on the east slope of the Eugene Mountains, in Pershing County, Nevada, 8 miles northwest of Mill City, a station on the Southern Pacific R.R. and on the Victory Highway. Fig. 1. Supplies and, concentrate are transported by truck over an automobile road of easy grade. The property is at an average elevation of 5500 ft. and climatic conditions are generally favorable for continuous operation throughout the year. The ore treated is supplied by two adjoining mines, the Stank and the Humboldt. Physical and mineral characteristics of the ores produced by these two mines are substantially similar, although variations occur in hardness and mineral distribution.' The economic mineral is scheelite (CaWO4), composed, when pure, of 80.6 per cent tungstic trioxide (WO3) and 19.4 per cent lime (CaO).

Jan 1, 1935

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

CONTENTS PAGE ANDERSON, ARVID E., and CAMERON, FRANK K.-Recovery of Copper by Leaching, Ohio Copper Co. of Utah. Discussed by Thomas B. Brighton, H. C. Goodrich, Arvid E. Anderson, Thos. P. Billings, Frank K. Cameron 2 BEESON, J. J.-Mining Districts and Their Relation to Structural Geology. Discussed by Charles Keyes, Chas. A. Porter 4 DOBBEL, CHAS. A.-Deep-hole Prospecting at the Chief Consolidated Mines. Discussed by G. W. Crane 10 CRANE, G. W.-Notes on the Geology of East Tintic. Discussed by G. W. Crane, H. E. Havernor, N. O. Lawton 11 SACKETT, B. L., BARDWELL, CARLOS, JACOBSON, SIMON, and JENSEN, N. H. Lead Smelting in Utah. Discussed by D. W. Jessup, B. L. Sackett, E. H. Laws 13 BARDWELL, E. S., and MILLER, Roy H.-Pulverized Coal as Fuel for Copper Refining Furnaces. Discussed by L. D. Anderson, E. S. Bardwell, C. P. Crawford 15 WIGTON, G. H.-The Chief Consolidated Volatilization Process and Mill. Discussed by Thomas Varley, S. G. Olmstead, V. O. Lawton, O. C. Ralston.... 16 JESSUP, D. W.-Evolution in the Preparation of Ores for Lead Blast Furnaces. Discussed by W. Spencer Reid, D. W. Jessup, Carlos Bardwell 19 ALLEN, H. P., and MADGE, WM. C.-Chloridizing Mill of the Standard Reduction Co. Discussed by Thomas Varley, H. R. Hanley, H. P. Allen, George H. Dern 20 TUCKER, E. L., and HEAD, R. E.-Effect of Cyanogen Compounds on Floatability of Pure Sulfide Minerals. Discussed by Blarney Stevens 24 Mix, B. E., and BARKER, L. M.-Method of Unloading Ores and Coarse-crushing Practice at Magna Plant of Utah Copper Co. Discussed by W. C. Madge,B. E. Mix 25 KEIGLEY, C. T.-The New Byproduct Coke Plant of the Columbia Steel Corporation. Discussed by W. M. Grant, C. T. Keigley, A. C. Feilder 25 JACKSON, P. W.-Blast Furnace Plant of the Columbia Steel Corporation. Discussed by W. R. Phibbs, H. M. Henton 26 OLDRIGHT, G. L., KEYES, H. E., and WARTMAN, F. S.-Production of Ferric Sulfate and Sulfuric Acid from Roaster Gas. Discussed by G. D. Van Arsdale William E. Greenawalt, G. L. Oldright 27 MAZANY, M. S.-Braden Copper Company Caletones Smelter. Discussed by A. B. Young, G. L. Oldright 36 HARRINGTON, D.-Safety Methods in Utah Coal Mines. Discussed by Edward K. Judd, Otto Herres, Benedict Shubart, A. C. Watts, D. Harrington 36

Jan 12, 1925