Search Documents

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By JOHN R. SUMAN

I WOULD like to spend a few minutes describing to you the present condition which exists in the oil industry and then point out some aspects of this deplorable situation in which I think petroleum engineers can be helpful. As you know, the oil business at this time is in a very critical condition, .due to the tremendous potential production in excess of current demand. This is a world-wide condition as well as a national problem, as it is estimated that the surplus production available for the market in foreign countries is of about the same proportion as that existing in the United States. Due to the inability within the United States to hold production within the bounds of demand prices have been slumping for the last four years and at this time have reached the point where the sales value of the average barrel of crude oil in the United States, is far below the cost, of production. In addition to the large amount of potential production available for the market in excess of demand we have in storage in the United States about six hundred fifty millions of barrels 'of oil. Unless something can be done to limit the amount of oil coming onto the market to a point well below the demand, which point will permit the reduction of stocks, it looks as though the 'oil business is facing demoralization.

Jan 1, 1931

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916

Reply to discussion of the paper of C. W. Washburne, presented at the New York meeting, February, 1914 (Trans., xlviii, 687 to 694 (1914)). C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Professor Lane makes an interesting contribution to the study. of chloride waters, in saying that calcium chloride waters occur not only in the greenstones of the Lake Superior copper mines, but also in the interbedded -felsitic conglomerates and "in far-removed sandstones, e.g., near Whitefish lake, and Ontonagon, in the Michigan iron mines, and in the Storm King granite." Surely these are not connate waters preserved from the Algonkian sea, assuming that the Algonkian sediments are marine rather than continental. Finding the same type of water in the Storm King granite points rather toward an abyssal source. The possible connection of these waters with the magma of the greenstone is immaterial, although some basic calcic magma is the most probable source. It is to be expected that the ascending water of the region would be found not only in the greenstones, but in all the rocks which it could penetrate. The ascent of water of this kind along vertical passages, and the consequent addition of a common ion: to the circulating sedimentary salt solutions, would explain the precipitation and localization of the "giant, concretionary" salt plugs of the Gulf Coast, without making the ex-excessive demand for an improbable quantity of salt in the adjacent sediments that is required by the unmodified theory of Harris. With-out such a precipitating medium most of the dissolved sodium chloride would have been lost by passing on to the surface without precipitation. The base to which the chlorine ions were attached is immaterial, providing they were sufficiently concentrated, but the presence of the chlorides of calcium and magnesium in the solutions is indicated by the associated bodies of secondary dolomite.

Jan 4, 1915

By Chandler Morse

RENEWABLE VS. NONRENEWABLE NATURAL RESOURCES Nonrenewable resources, such as minerals, are the inevitable center of attention in discussions of depletion and exhaustion. Nevertheless, it may well be proper to regard some nonrenewable resources as not subject to exhaustion, and renewable resources may sometimes be treated as if they were finite stocks. Thus, the availability of nonrenewable resources is not and probably never will be known completely Chap. 2.5A, and therefore is not subject to firm predictions concerning exhaustibility. Moreover, because exploration and discovery are more or less continuous processes it is often appropriate to regard mineral supplies as flows, and to treat the estimated reserves as working capital, an inventory, continually depleted by use and augmented by discoveries.23 The aggregate economically exploitable stocks of a given mineral are seldom estimated (or estimatable) with precision, as Chap. 2.5A shows, and even when they are, forecasts concerning years of remaining life can be and often are falsified by changes in one or more of the multidimensional conditions of supply and demand; or the productive services formerly derived from an exhausted stock may continue to provided without material impairment by one or more substitutes b Conversely, the renewable resources are all subject to depletion when the rate of use exceeds the natural or induced rate of replenishment, and cases of exhaustion or near exhaustion, as through soil erosion, overcuttmg of forest lands, and overfishing, are rather common c Where exhaustion is a clear possibility the resource may either be exploited on a consciously adopted "sustainable yield" basis or be treated as an exhausting asset." In some cases, conscious treatment

Jan 1, 1976

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

By Guillermo Zuloaga

THE iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana High-lands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Profes-sor Lindgren and Professor Newhouse.

Jan 1, 1933

By N. L. Svensson

The model developed by Tuylor for the calculation of Polycrystalline yield strength has been applied to the case of an aggregate hawing a preferred orientation. In general this procedure requires the specification of texture by means of weighting factors applied to specific orientations. The problem to which the model has been applied is that of the yield-strength aniso-tropy of cold-rolled aluminum whose rolling texture was described as a combination of (110)[112] and (311) [112] In this case yield-strength anisotropy is defined by the rutio of yield strength measured at an angle 8 to the rolling direction to that measured along the rolling direction. The method of calculation of yield-strength ratio as a function of ? is described and the results show good agreement with experimental values. The orthotropic yield criterion suggested by Hill has been applied to the results and the strain ratio R also calculated as a function of ?. This has been compared with calculations using the method suggested by Elias, Heyer, and Smith which does not exhibit suck good agreement with observation. one deficietlcy of the method presented is that the strain ratios used by are those applying to iso-Irobic materials. The method should therefore be reg-clrded only as a first abbroximation to the prediction of anisotropy. THE problem of calculating the stress-strain characteristics of polycrystalline aggregates from the properties of single crystals has attracted attention for a number of years. The most important contributions to this study have been those due to: Sachs,' Cox and sopwith,2 Taylor,3 Kochendorfer,4 Batdorf and Budiansky,5 Calnan and Clews,6 Bishop and Hill,7,8 Kocks,9 Budiansky, Hashin, and sanders, 10 Kroner,11 Cyzak, Bow, and payne, 12 Budiansky and Wu,13 and Lin.14 While the earlier work has been largely superseded, recent developments tend to support Taylor's solution" within the restriction imposed by his assumptions. The essential features of Taylor's approach were: 1) the material is rigid-plastic; 2) each grain experiences the same strain components as the aggregate as a whole (the problem was that of uniaxial deformation with principal strain components in the ratio 3) all regions of each grain deform uniformly; 4) work hardening occurs equally on all slip systems. While Bishop and Hill7 have generally validated this approach, there has been some criticism offered. Kocks? as pointed out that since multiple slip must occur the single-crystal data must be determined from orientations arranged such that polyslip takes place. Boas and Hargreaves,15 and others, have shown experimentally that the strain distribution within grains is not uniform, the strains in the vicinity of grain boundaries being less than those in the center of the grains. Both of these criticisms can be largely offset by the suitable choice of single-crystal critical shear stress. However, for the problem analyzed below, the critical shear stress is not directly used and, consequently, these criticisms lose their importance. The more recent contributions have attempted to obtain a more complete analysis by considering an elas-toplastic material and considering interactions between grains of differing orientations. Lin14 has considered the early stages of yielding for a polycrystalline aggregate having specific regions of defined slip plane orientations. On the other hand, Budiansky and Wu13 have allowed for these interactions for randomly disposed grain orientations and have calculated the polycrystalline stress-strain curves for crystals exhibiting either elastic-ideally plastic or kinematic hardening characteristics. This work has shown that yielding commences when the macroscopic stress is 2.2 times the critical shear stress for slip in a single crystal (7,). The yield stress-strain curve then rises becoming asymptotic to a value of 3.072 7,. This is close to the value obtained by Bishop and Hill (3.06) in their confirmation of Taylor's method. This, of course, is to be expected since, at large strain values, the elastic strains are negligible and the rigid-plastic model is satisfactory. The results of Budiansky and Wu indicate that the result obtained by Taylor is 7.7 pct high at a plastic strain which is two times the elastic strain at the initiation of yield. By defining the anisotropy in terms of relative values, the ratio of yield strength at orientation ?, to that measured in the rolling direction, the effect of the discrepancy in Taylor's solution is considered to be of lesser consequence. Therefore, it is anticipated that an analysis based on Taylor's solution, which can be quite straightforward, should provide a reasonable estimation of the anisotropy of materials having a preferred orientation texture. OUTLINE OF TAYLOR'S METHOD In fee metals there are four possible slip planes (the octahedral planes) and in each there are three possible slip directions (the edges of the octahedron), that is a total of twelve possible slip systems. von Mises16 has shown that at least five independent slip systems must become operative in each grain of the polycrystalline aggregate in order to preserve continuity of strain. With this geometrical requirement as basis and the assumptions previously listed, Taylor determined the operative slip systems for a number of orientations of the tensile stress axis specified in the unit stereographic triangle. For the ith slip system, the critical shear stress

Jan 1, 1967

By Norman D. Fitz Gerald

THE growth of domestic requirements for motor fuel has been phe-nomenal, rising year after year in a fashion almost unique among com-modities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influ-ences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The com-plexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simul-taneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpreta-tion of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the prob-lem is confined to the measurement of the influences of statistically

Jan 1, 1940

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By George S. Rice

DEFINITE data on the amplitude and effect of ground movement in specific mineral formations, caused by various methods used in the mining of ores, coal, and nonmetals, or in the extraction through wells of petroleum, sulphur, and soluble salts, are increasingly needed because of legal liabilities from damage to overlying or adjacent properties, and growing concern as to the conservation of national mineral resources. Not since the committee was established in 1923 has it been so difficult to get technical papers giving ground movement and subsidence data from specific mine operators. The reasons given, as above indicated, are pending or threatening lawsuits. There are three major objectives in ground movement and subsidence studies : (1) Maximum recovery of a mineral resource. (2) Minimizing damage to surface structures, highways, railroads, and agricultural lands caused by caving or subsidence, which may in some situations, as along the Gulf of Mexico shore, cause flooding by surface waters. (3) Lessening damage to overlying or adjacent mineral by back-filling of mine excavations as completely as possible.

Jan 1, 1940

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

THE slag performs two useful functions. in open-hearth steel-making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SO2, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (SiO2 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1951

By M. O. Holowaty, C. M. Squarcy

Blast furnaces are the tools of men, and it is men who have made them great. Here is presented the story of the Ironmakers-the men who first poured hot metal into what would someday be the sinews of a nation. W HEN the Jacobean merchant adventurers bade farewell to the first ship of colonists sailing for the new land, they instructed them to direct all their skill and energy to grow silk worms in Virginia. The adventurers felt sure that they could flood the market with highly priced and much desired goods like silk, sugar, tea, and indigo. They were also convinced that they would fill the needs of the mother country for iron. Early iron production in the colonies The merchants certainly had a wonderful imagination, for silk and indigo were just as exotic in Virginia as they were in England. The settlers found it more profitable to raise tobacco on the vast stretches of the free, fertile land. Thus the plans of settlers clashed with those of The Virginia Co.; and only point of agreement was the desire to produce iron. But, even there the motives of the settlers and those of The Virginia Co. of London were worlds apart. The settlers wanted to produce the tools badly needed in the colony, while the Company desired to cash in on the rising demand for iron which the home industry could not satisfy. Both the settlers and the Company lost no time trying to find iron ore. Locations of the early mines are not known. If, however, the reports of the Irishman, Francis Maguel, can be trusted, as early as 1609 a ship sailed for England with a load of 17 tons of crude iron which the East India Co. purchased at £ 4 per ton. The iron was of excellent quality and considered the best iron made of non-English ore that was ever purchased.

Jan 1, 1961

By R. S. Archer

In the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the hcat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis, heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while in others, especially in those whose grain is unusually fine or in which the final hardening heat has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters. The properties of the steel are as follows: Carbon, per cent............... 0.42 Brinell hardness.............. 293 Nickel, per cent................ 1.35 Yield point, pounds per square Chromium, per cent............. 0.90 inch........................ 131,000 Copper, per cent................ 0.025 Maximum strength, pounds per Manganese, per cent............ 0.74 square inch................. 144,500 Phosphorus, per cent............ 0.024 Elongation in 1 in., per cent... 28 Sulfur, per cent................ 0.036 Lod impact, foot-pounds...... 51 Reduction of area, per cent...... 57.3

Jan 1, 1920

By Carl Henrich

The Ducktown copper-mines are located in the southeast corner of Tennessee. The name Ducktown was originally given to a district occupying the southeast corner of Polk county, which in turn occupies the southeast corner of the State. Fig. 1 is a map of the vicinity of Ducktown, taken from the topographical surveys of the United States Geological Survey. The Ducktown district is bounded on the east by Cherokee county, North Carolina (the boundary-line between the two States running here a little east of north along the western slope of Pack mountain), and on the west by the eastern foot-hills of Little Frog mountain. On the north, Stansbury mountain, really a chain of low mountains or hills, forms the dividing-line between Ducktown and Turtletown districts. On the south, the Ducktown district extends beyond the Ocoee river to the Georgia State line.. This line, in going west, gradually recedes southwards from that river into the foot-hills of Big Frog mountain, the highest mountain of the neighborhood, which rises about 4300 feet above sea-level, while the surface of the Ocoee river, where it leaves the Ducktown district, is less than 1500 feet above sea-level. It will be seen from this description, and from a study of the map, that the Ducktown district occupies the northern part of a kind of basin, bounded on the east by Pack mountain and on the west by Little and Big Frog mountains. Between these mountains the Ocoee river, draining the basin, cuts its way to the Hiwassee and the Tennessee rivers in a narrow gorge, through the crystalline slates and schists, which from their excellent exposure in this Ocoee gorge have received the local

Jan 1, 1896

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By F. B. Plummer

PRODUCING operations abroad during 1940 were shrouded in the fog of war. Little, if any, concrete information is available, and the data that issue from the belligerent countries are too frequently distorted for military purposes, for the volume of supply of gasoline and fuel oil has become an important strategic secret. Despite this lack of information signs indicate the spread of a slow paralysis which is gripping producing operations in foreign countries. Only in the Caribbean area are developments proceeding normally and even there the destruction of the Western European market is being seriously felt. This creeping paralysis is being brought about partly by the serious shortage of materials so necessary for drilling and other producing operations such as steel, machinery, and the like-together with a scarcity of that prime munition of war-money. Markets too have been curtailed by the operation of exchange control as all exchange is needed to support war efforts. As a result, gasoline is tightly rationed in all belligerent countries. The growing casualties in shipping are fast restricting the water-borne trade in petroleum, but have had a local stimulating effect in some areas where the risk is less or where water-borne transport can be efficiently used as for instance Trinidad and Egypt. The type of product needed for war effort, particularly the great demand for aviation gasoline, has changed the schedules of .refinery operations. As a result of all these influences the world oil picture outside the United States- has vastly changed during the year.

Jan 1, 1941