Search Documents

By AIME AIME

FOR the development of a mine, a shaft of small cross-section is usually sunk, of no larger size than is absolutely necessary. After the mine has been developed and put on a production basis it is a common practice to sink a shaft of larger cross-section for hoisting and use the original shaft for the handling of men and material into the mine. While that ar¬rangement is usually expedient, the small size of the supply cages presents a problem in the handling of ma¬terial. Where a cage is, say, 4 by 4 ft., which is not an uncommon size, all lengthy and bulky material must be handled piece by piece several times from the supply department to the underground stations. Thus drill steel and timbers over 4 ft. long will be loaded on cars at the supply department and wheeled to the shaft, where each piece must be unloaded from the cars and stood up in the cage. They are then lowered to the shaft station, unloaded piece by piece and placed in cars, run to the supply station and again unloaded and stored until called for. In such a case handling becomes a major item in the cost of supplies.

Jan 1, 1930

By T. H. Alden

A correlation has been found in rock-salt structure single crystals between the latent hardening, measured by the direct stress activation of oblique slip systems, and the stress-strain behavior in simple compression. Materials with high latent hardening, like LiF, strain-harden at a low rate (Stage I) even when severely constrained. KCl, in contrast, shows low latent hardening and a tendency to strain-harden at a high rate (Stage 11). This correlation suggests that oblique slip is essential for Stage II hardening of these materials. THE role of secondary slip in the strain hardening of metal single crystals is a topic of lively controversy. On the one hand are theories in which secondary dislocations participate directly in Stage II hardening in the fcc metals, for example through the production of sessile dislocations,1 forest intersections, or jog formation. Much of the experimental evidence on which these theories are based has been reviewed by Clarebrough and Hargreaves.~ On the other hand, a recent theory5 denies that secondary slip has an essential role in Stage II hardening or in the transition from Stage I to Stage 11. In the latter view, Stage I is not terminated by an increase in the activity of secondary systems but by the exhaustion of undeformed material.6 The experiments reported in this paper will not resolve this controversy since the materials being studied are cubic ionic crystals rather than metals. However, the results do show in an unusual way a direct connection between "secondary" (nonortho-gonal or oblique) slip and strain hardening in these materials. Specifically, a correlation has been found between two independently measured properties, first the latent hardening of oblique (110)(1i0) slip systems as measured by direct stress activation of these systems, and second the stress-strain behavior at small strains. From prior work, it was known that in most cubi-cally oriented rock-salt structure crystals, two orthogonal slip systems operate and exclude the other equally stressed pair, oblique to the first pair.7'8 This observation apparently indicates that a significant interference exists between slip on oblique (110) planes and a relatively small interference between orthogonal (110) planes. The present experiments were begun with the intent of obtaining a quantitative measure of this difference by means of a study of latent hardening in these crystals. I) EXPERIMENTAL METHODS The experiments were basically of two types, first the determination of stress-strain curves by compression along a single (100) axis, and second the measurement of latent hardening by compressive prestrain along one cube axis followed by the determination of the yield stress in a second (latent) cube direction. All tests were done at room temperature in an Instron machine by compression between lapped, parallel steel faces. Three specimen shapes were used. For long crystals (nominal dimensions, 1/8 in. square by 1/2 in. long) the ends were lubricated with an oil-graphite mixture. Superior results with short crystals (about 1/8 in. cube) were obtained using 0.003-in. teflon film.' Thin crystals (1/4 in. square by 3/32 in.) were used for latent-hardening measurements and similar results were obtained with either lubricant. Test specimens were cleaved from Harshaw single crystals which had been irradiated to a dose of lo8 roentgen using a cobalt-60 source. The irradiation raises the yield stress and tends to prevent plastic deformation during sample preparation.10 Prior to testing, the irradiation hardening was removed by an anneal at 400°C. Ideal compression specimens have flat, parallel faces. In short specimens particularly, satisfactory results demand a close approximation to this ideal. In the present work, cleaved surfaces were often used directly as compression faces. The degree of success using this method depends on two factors: 1) the smoothness of cleavage faces, and 2) the extent to which the crystal is deformed or crushed by the chisel during the cutting of a long crystal into short pieces. Unfortunately, only one material of those studied, LiF, was completely satisfactory. NaF, NaC1, KC1, and KBr behaved less well so that

Jan 1, 1964

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By Alfonso W. Ovalle, Héctor R. Albornoz

INTRODUCTION The El Teniente Mine of Codelco-Chi le has extracted 588 mil lion tons of ore in its 77 year history for a total copper output of 8.800.000 tons. The mine production has been obtained mainly by traditional block-caving where grizzlemen using a hand held lever send ore through long-raises to load trains. At present the mine is about to introduce mechanized block-caving using LHD equipment to extract the primary rock. This paper describes this method which will be tested starting next month by caving an 11.000 square meter block. THE PRIMARY ROCK PROBLEM The secondary enrichment sulfides of the El Teniente ore body have characteristics which makes a standard unmechanized block-caving practice very successful. In the 60&apos;s parts of blocks encountered primary ow in the Teniente 1 and Sub-13 levels which proved to be extremely hard to extract. These foretold the obstacles that arised in the central part of the Teniente 4 level. Preparation of a completely primary 8.100 square meter block started in 1970. Its undercutting was completed by the end of 1972 and by 1973 the problem of mining the primary rock was clearly visualized. The numbers below describe the difficulties in mining this block: -Long-hole drilling rate is 90 m (270 ft) per shift in secondary rock and 37 m (110 ft) in primary. - Undercutting which is completed in 9 shifts in secondary took 180 shifts in the primary block. - Average grizzlymen productivity in secondary is 250 tons per shift while in primary it is only 25-30 tons, both at 343 mm (13 1/2 in. ) grizzly opening. - Powder consumption for secondary blasting increased from 8 grams per ton in secondary to 84 in primary. - The protection pillar between the under- cutting and the production levels was 60% broken in primary while 20% is usual for secondary. - Extraction advanced 5 cm per day in primary while a 50 cm per day rate is the aver- age in secondary. This is the main reason that after 8 years this primary block has a 20% extraction. Secondary blocks take 1.5 to 3 years to complete their extraction. - 80% of the boulders in primary rock are larger than 343 m (13 1/2 in.) with 10-20 % of them larger than 3 meters. -Direct cost of production (preparation, undercutting, extraction and haulage), using the traditional block-caving design for secondary rock, increased 3.5 to 4 times when used in primary rock. The following indicators of Table 1 show the rock characteristics differences.

Jan 1, 1981

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.&apos; A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976

AS If see it, then, the engineering advances of which yob have studied here at Golden, the continued growth of. industry that you see about you here in Colorado, and the country-wide progress that I have not time to discuss-these illuminating facts should clear away any doubts as to your future. You have little license to ask, "Where is the call for engineering or what the need? Yankee fashion I might ask you by way of reply, "Have all the mines been opened? Have all the power-houses and transmission lines been built? Have the last improvements in. mill and smelter been in-stalled?" We know that the general answer is No, and the rest of the answer, which tells where are those mines and power plants and what are the new methods and processes in mining and metallurgy, must be sup-plied by you engineers of the future. And anyone who has even casually observed what recent years have brought forth in our profes- sion cannot but envy you your job. Our reconnaissance excur-sion into your future should not be much longer extended, but before turning back there are four landmarks that I would like to point out-not lofty peaks but useful tie points that are worthy of your attention as you traverse the territory of your future work. Two of these are in fact low spots or depressed areas which call for engineering activity; these are commonly called "waste" and "average." The other two are of larger significance and are rather extensive regions in the domain you are to enter and occupy. These larger tracts bear the suggestive place names "fact-finding" and "human engineering" and perhaps will prove to be the heights from which the broadest outlook is to be had in this "pilgrim&apos;s progress:" In the first place, waste deserves your attention, al-though I realize that it is possibly the most unpopular word anyone hailing from Washington can publicly utter. Its unpopularity naturally follows from its overuse in the somewhat strong charges made against the industrial and business world some years ago, when the doctrine of conservation was first preached in the land. But waste is a word to be used in an engineering sense as well as for political effect. Properly used, waste is not a word to shy at-rather it is a challenge to the engineer. For example, at present, the loss of 1 kilowatt-hour to every 5 sold is a clarion call to the electrical engineer. Waste is your target to shoot at, the obstacle for you to surmount, the giant for you to slay.

Jan 7, 1928

By Charles W. Carter, Alfred H. Bell

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year&apos;s total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By Alfred H. Bell, Charles W. Carter

In 1942, Illinois produced 106,590,000 bbl. of crude oil, or 7.6 per cent of the entire amount produced in the United States. It ranked fifth among the oil- producing states. The production for 1942 declined 20.5 per cent from the previous year&apos;s total of 134,139,000 bbl. Tie daily average production for 1942 was approximately 292,000 bbl., or 74,000 bbl; less than the 366,000 daily average for 1941. At the beginning of 1942 the daily production was 367,000 bbl. This production declined steadily to 282,000 for June and to 246,000 for December. This steady decline was caused partly by the reduction in drilling resulting from Federal Conservation Order M-68 and partly by the fact that no major pool was found during the year. Discoveries Forty new fields (Fig. 2, Table 2), 48 extensions (Table 3), and 45 additional producing zones in existing fields (Table 4) Were discovered in 23 counties in Illinois during 1942. Of the 40 new fields, three

Jan 1, 1943

By B. R. Palmer, M. C. Fuerstenau

Oxide and silicates respond to flotation with a large number of anionic collectors. These include carboxylates (fatty acids), sulfonates, alkyl sulfates, and certain chelating agents. In contrast to sulfide mineral flotation, relatively long-chained collectors (generally longer than 10 carbons) are required to effect flotation of this group of minerals. The structural formulas of these various anionic collectors are presented in Table 1. Formulas and solubilities of various fatty acids are presented in Table 2. These solubilities are those of the dissolved and undissociated species of the acid, e.g. oleic acid, HOl(aq). Of the compounds listed, oleic acid and abietic acid, which IS a major constituent of talloel, are used most commonly in commercial applications. The usage of these two collectors is related to cost and effectiveness. In addition to their high molecular weights, oleic acid contains a double bond in its hydrocarbon chain, while abietic acid is comprised of aromatic rings containing double bonds. The presence of double bonds increases solubility significantly over that of saturated homologues. Stability of metal-collectors assumes a most significant role in these systems, and the solubility products of various metal carboxylates and sulfonates are listed in Tables 3, 4 and 5. In addition to these properties, strength of the acids of these various anionic collectors is also important. The carboxylic and hydroxamic acids are weak acids whereas sulfonic and alkyl sulfuric acids are strong acids. All of the carboxylic acids fall in the range of pK = 4.7 ± 0.5 ([2]); the pK of hydroxamic acid is around 9 ([3]); and the pK of sulfonic acid is about 1.5 ([4]).

Jan 1, 1976

By C. Dinis da Gama

In order to reduce the complexity of mechanisms influencing rock. fragmentation by blasting a simulation approach is proposed, using the capabilities of microcomputer interactive graphics. Situations involving cratering end bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

COUNCIL OF SECTION DELEGATES F J Meek, Chairman H A White, Vice-Chairman H R Gault, Secretary Division of Earth Sciences National Research Council 2101 Constitution Avenue Washington 25, D C

Jan 1, 1954

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke&apos;s paper is published in full as it shows clearly the good results of the Institute&apos;s work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke&apos;s paper is published in full as it shows clearly the good results of the Institute&apos;s work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf&apos;s in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By J. R. Campbell

During the past few years, the writer has had occasion to take several excursions into the realms of the washability of beds 3 and 4 of the Pocahontas coal and the proper handling of these coals in prepared sizes Fig. 1.—Washability curve for 4 by 2½-in. egg, PocahoKtas coal. Note that definite break occurs at about 1.60 sp. gr., and washing at this gravity removes all heavy rock and slate, amounting to about 5 per cent. Curve 2 indicates a bony coal, and washed egg coal might not have a good appcarance, and would be condemned by visual inspection, although it would be well prepared mechanically. to attain the greatest realization for the operator and yet produce a market product acceptable to the consumer. Preparation is not new in the southern field, but some new angles have presented themselves in recent years on account of the progress of mechanical preparation. Mechanical methods are entirely devoid of the five senses given to

Jan 1, 1931

The Manufacturer&apos;s Viewpoint A prominent manufacturer of mining &apos;machinery not long ago expressed himself as being confident that he was securing the best kind of publicity for his product through the advertising pages of the monthly Bulletin of the American Institute of Mining Engineers. Such an expression coming from such a man is highly gratifying; yet it is justifiable when the high quality of reader and subscriber is taken into consideration. In fact, the majority of those using our advertising pages feel the same. It is to be regretted, of course, that others catering to our field do not realize the means at their disposal for presenting the points of interest of their product to the mining man. The question has been asked, " Do your members read their Bulletin?" They not only read the editorial pages, but they "admit being up-to-date enough to peruse the advertising section to "see what is new." The next question the prospective advertiser asks is, " Will the Bulletin bring inquiries?" The answer to this question holds good for any publication having as subscribers those who have purchasing or recommending power-yes, if the article advertised is not a stock one, that has been before the public for any length of time. To secure inquiries on, say, a standard centrifugal pump or any other standard product, the features of which are well known, is a most difficult proposition. Yet, of course, some inquiries are secured, but mostly from those having use for the catalogue or trade literature for reference purposes. It is safe to say that the traceable returns from advertising in trade publications hardly, if at all, pay for the advertising. The real returns are intangible, and result from the constant publicity, and keeping ?everlastingly at it." Who can say what subconscious effect is taking place when an advertisement is "glanced at," to say nothing of the effect produced when the copy is attractive and interests the reader. Time after time it has been proved that sales have been secured as a result of an advertisement, yet no inquiry had been made directly traceable to advertising.

Jan 8, 1915

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler&apos;s saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By V. GUDKOV

THE iron-ore deposits of Russia were estimated at 2,200,000,000 by the Russian Geological Survey, in 1910; but this estimate must be considered as being far too low. The estimate for Siberia, which had been explored very little for iron ore, was placed at about 27,000,000 tons. The exploration, in 1912-14, of the three iron deposits-Blagodat, Baakal and Kamensk-raised the estimate of the iron-ore reserves or the Urals from 282,000,000 tons to about 400,000,000 tons. Conservative estimates of the explored deposits made by the writer in 1915, gave the following figures: Southern Russia 900,000,000 tons, Ural Mountains 500,000,000 tons, Central Russia 900,000,- 000 tons, Siberia 100,000,000 tons, Caucasus 20,000,000 tons, or a total of 2,420,000,000 tons of iron ore, or 1,200,000,000 tons of pig iron.

Jan 1, 1921

By Charles H. J. Patterson

When coal is deposited on the decks of pneumatic tables, all fine particles clinging to the larger pieces are blown free by the air. Inasmuch as the air retains an appreciable residual velocity after passing through the bed of coal, it is capable of suspending particles of goodly size. This velocity is dissipated gradually and, unless confined, can readily extend beyond the limits of the plant. Today the ideal in the design and operation of pneumatic cleaning plants is not that they be no dustier than the ordinary tipple, but rather that they be as clean as an office or shop. This degree of perfection may not yet have been attained in any commercial plant, but it is not impossible of achievement. Not until recently has the recirculation principle been applied to pneumatic separating plants. In the writer&apos;s estimation, it has not yet been proved entirely satisfactory in commercial installations. A serious obstacle lies in the fact that it is practically impossible to provide a truly closed circuit. The air circuits must be interrupted at certain points, if only for the introduction of raw material and for the recovery of the finished product. It is feasible to prevent the escape of polluted air at these points, but this can scarcely be accomplished without admitting additional air into the circuit. These additions of air are cumulative, which necessitates means for emitting to the atmosphere the excess while still carrying its objectionable burden, if provisions are not made for conditioning. If it must be provided at all, conditioning is frequently simpler and more economical if applied to the entire volume of air involved. This procedure eliminates the extra initial cost and operating expense of the closed system. Crane Cheek Experiments The first noteworthy commercial installation of pneumatic equipment was made in 1922, at the Crane Creek plant of the American Coal Co. of Allegheny County, at McComas, W. Va. Six tables for cleaning coal between the limits of and 3 in. comprised the initial installation. Dust was collected by hoods connected by a system of ducts to exhauster fans. In this installation the unit dust burden was small, owing to the removal of fines from the feed by vibrating screens.

Jan 1, 1931