Search Documents

By Carl Benedicks

IT is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).1 A study of the microstructure or local chemical composition of the metal (iron; 70 :30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point-to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the fact that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion"2 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."' In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corrosion."4 On consulting the many textbooks on corrosion, as that

Jan 4, 1925

By L. D. Hall, D. R. Mash

The paper presents the results of experiments on the anelastic. behavior of gold, as manifested by grain boundary relaxation. Two grain boundary internal friction peaks are found for 99.9998 pct Au. It is found that the peaks are associated with primary and secondary recrystallization. However, the existence of two discrete peaks cannot be explained on the basis of grain size and shape alone. It is suggested that grain boundary stability, as determined by orientation, plays a role in the observed effects. EVIDENCE for the viscous behavior of grain boundaries in metals has been presented in recent years by several investigators, based upon studies of various anelastic effects, especially internal friction. KG1 has contributed greatly to this field, having put forward a coherent body of evidence for stress relaxation by the viscous intercrystalline flow mechanism. In this connection, he has made extensive use of pure aluminum (99.991 pct) as the test material, although he has also studied other metals and alloys, including pure iron (Puron).² Rotherham, Smith, and Greenough³ have studied the internal friction of pure tin, interpreting their results in a manner similar to that of KG. In view of the importance of such studies in shedding light upon the fundamental structure and behavior of the grain boundaries in pure metals, it appears that the use of a very pure test material which is inert to its environment should provide useful information on anelastic properties and the source of such behavior in pure metals. The present work was carried out on spectrograph-ically pure, 99.9998 pct Au, free of all impurities except for a trace of silver, estimated to be present to the extent of about 0.0002 pct. The term "pure gold" will hereafter refer to this very pure material. Gold of commercial purity, 99.98 pct, was also studied to observe the effects of small amounts of impurities. A pure gold "single crystal" specimen was also tested for comparison. The variation of the internal friction and rigidity modulus as a function of temperature was determined by means of a torsion pendulum apparatus employing extremely low stress amplitudes and a frequency of vibration of the order of 1 cycle per sec. A 12 in. length of 0.031 in. (20 gage) gold wire formed the suspension element. The apparatus was similar to that described by Ke.l The test procedure and the basic requirements to be met for obtaining useful experimental data by this method have been given elsewhere.1,2 It should be made clear that in all of the experiments to be described, the internal friction and rigidity were independent of the amplitude of torsional vibration. The semilog plot of amplitude of vibration vs ordinal number of vibration was a straight line. This was carefully verified for each internal friction measurement. The linear variation shows that the internal friction was independent of stress; i.e., that the specimens were not being cold-worked during testing. The reproducibility of the internal friction curves, which were obtained by cyclic heating and cooling, indicates that the gold was unaffected by its environment during the tests. The measure of internal friction adopted in the present study is the conventional "logarithmic decrement," defined as follows: log. dec. = l/n In A0/An [I] where n is the number of cycles or vibrations; A,, the initial amplitude of vibration; and An, the amplitude after the nth cycle. When the logarithmic decrement is small, the shear modulus, G, of the wire is proportional to the square of the frequency of vibration provided the length and radius of the wire are kept constant. A plot of frequency squared vs temperature gives the following ratio:' This expresses the fraction of the stress which has not been relaxed at a given temperature. Gr and Gv are the relaxed and unrelaxed moduli, respectively. The frequency of vibration in the polycrys-talline specimen is fp, and the frequency of vibration of a single crystal is f8. This latter quantity is obtained simply by extrapolating the linear, low temperature portion of the curve of frequency squared vs temperature for the polycrystalline specimens. The theory of viscous grain boundary stress relaxation as demonstrated by the anelastic behavior of metals has been discussed in detail by Zener4 and need not be reproduced here. Experimental Results Initial measurements of the internal friction of pure gold were carried out on specimens which had been drawn with no intermediate annealing, resulting in a material which had undergone approximately 99 pct reduction of area in final processing. Annealing was then carried out at successively higher temperatures starting at 400°F for 1 hr and proceeding in this manner to as high as 1600°F in 100°F intervals. After each annealing treatment an internal friction and rigidity vs temperature curve was obtained over the range from room temperature to the particular annealing temperature. The resulting internal friction curves did not exhibit well defined maxima (peaks), but rather several fairly flat

Jan 1, 1954

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

THE only asbestos mine in the Middle East is on the Island of Cyprus, high in the Trodos Mountain village of Amiandos. The mine is owned by the Tunnel Asbestos Cement Co. Annual output is some 18.000 tons of short fibre in the 4-T. 4-Z, and 5-R grades.

Jan 9, 1953

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

Feb. 5, 1917. To the President, Executive Mansion, Washington, D. C. We, the presidents of the national societies of Civil, Mining, Mechanical and Electrical Engineers and of the United Engineering Society, with a membership of thirty thousand, cordially unite in supporting Congress and the Administration in its stand for freedom and safety on the seas, and we are confident that we represent the membership of the four societies in offering to assist toward the organization of engineers for service to our Country in case of war. GEORGE H. PEGRAM, President of the American Society of Civil Engineers. L. D. RICKETTS, President of the American Institute of Mining Engineers. IRA N. HOLLIS, President of the American Society of Mechanical Engineers. H. W. BUCK, President of the American Institute of Electrical Engineers. CHARLES F. RAND, President of the United Engineering Society.

Jan 3, 1917

By John R. Dyni

Colorado nahcolite deposits, estimated at 29 Gt, formed in an asymmetric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCO3) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62%), disseminated crystals (24%), and impure beds (13%). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening. Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a Possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1982

By V. B. Kurfman

The temperature, strain rate, and orientation deDendence of defbrnzation of single-crystal MgAg has been examined. The crystals exhibit a tendency to single glide and little or no hardening at 25°C for many orientations. A much higher hardening rate is observed when multiple glide occurs, such as can be initiated by surface defects. The tendency for easy glide becomes less dependent on surface preparation and orientation as T — 100°C and bars so tested often fail after one-dimensional necking-. At T > 200°C (transition temperature for single-crystal notch sensitivity and poly crystalline ductility) single glide diminishes and two-dirnensionul necking begins. The crystals do not strictly obey a critical resolved shear stress law, but show the influence of {loo) cracks in determining the slip mode. The results are correlated with the difficulty of sciperdzslocation intersection and semibrittle behavior of this compound in single-crystal and poly crystalline form. Comparisons are made with the slip selection mode observed in tungsten, with the reported observations of easy glide in bee metals. and with the mechanical behavior of poly crystalline MgAg. PREVIOUS work on tensile deformation of polycrys-talline MgAgl and bending deformation of single-crystal MgAg2 has shown that the compound is semi-brittle (i.e., notch and grain boundary brittle). If this semibrittleness is supposed to result from the difficulty of multiple glide (associated with the problems of superdislocation intersection) one might expect single crystals deformed in tension to show pronounced single glide and strong orientation dependence of hardening rate. These experiments were done to examine this supposition and to study the tensile deformation of a highly ordered system which may be considered bcc if the difference between the two kinds of atoms is ignored (actual structure: CsC1). EXPERIMENTAL Single-crystal ingots were grown by directional freezing as previously described.' These ingots were sliced into a by a by 2 in, rectangular bars by electric discharge machining, then round tensile bars were conventionally machined to 1/8-in.-diam by 1-in.-long reduced section. The bars were typically tested without an anneal because of the problem of magnesium vapor loss and they were typically tested as mechanically polished. The analyses are within the same limits as those reported earlier; i.e., the average composition for each specimen is within 0.5 at. pct of stoichiometry, while the total range from end to end in a given specimen varies from 0.7 to 1.4 at, pct. There has been no indication in the results of any variation in slip or fracture mode attributable to the composition fluctuations. The slip systems were determined by two-surface analysis of the bars after testing to failure at room temperature. Single glide was so dominant that there was little difficulty in identification of the dominant slip system even though the tensile elongation to failure often approached 7 to 8 pct in room-tempera- ture tests. Elevated-temperature testing was done in a silicone oil bath and low-temperature testing was done in liquid Np or a dry-ice bath. All stress measurements are reported as engineering stress unless otherwise specified, and crosshead travel is used as the strain measurement. RESULTS The tendency toward single glide is best seen in the pictures, Figs. 1, 2, and 3, which depict deformation at fracture as a function of test temperature. While it is possible to find regions of secondary slip by careful microscopy, such regions are very small. The development of a ribbon-shaped configuration from an initially round section bar pulled at 100°C is typical, occurred by single glide, and illustrates the degree to which such glide continues. At temperatures =100°C the bars typically show elongation of 20 to 50 pct by predominently single glide. Despite the large elongation, fracture even at 150°C occurs in a brittle mode, Fig. 2, in the sense that it is an abrupt failure which shows no discernible necking in the second dimension of the bar's cross section (i.e., there is no appreciable action of any slip modes which would decrease the broad dimension of the cross section). Near 200°C the fracture mode changes slightly. Although most of the sample extension is by single glide, after the bar develops the characteristic ribbon shape it begins to neck in the second (i.e., broad) cross-sectional dimension. The bar becomes very thin in the "necked down" region, Fig. 3, and the reduction in area approaches 100 pct. Often there oc-

Jan 1, 1967

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By D. R. Parrish, T. M. Geffen, R. A. Morse, W. W. Owens

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By Daryl R. Tweeton, William H. Engelmann, Orin M. Peterson, Jon K. Ahlness, Gregory R. Anderson

The Bureau of Mines measured the geochemical changes as H2SO4 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen,HC03, U. V, Na, K, Ca, Mg,S04, CI, Mo, Mn, Fe, AI, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By D. F. Botkin, B. H. Sage, W. N. Lacey

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By W. N. Lacey, D. F. Botkin, B. H. Sage

Joule-THomson coefficients for two natural gases were determined at pressures up to 600 lb. per sq. in. throughout the temperature interval between 70" and 310°F. From these primary data and available information relating to the isobaric heat capacities of the components at infinite volume, the heat capacities of these gases were computed throughout the above-mentioned range of pressures and temperatures. The enthalpies of the gases were computed as a function of state and the results compared with values obtained by several methods of prediction currently available. Table i .—Composition of Gas Samples Components Gas A Gas B Carbon dioxide................ 0.0090a 0 .042 0 Methane...................... 0.8255 0.8385 Ethane.......................0.0901 0 .0637 Propane....................... 0.0462 0.0374 Isobutane..................... 0.0074 0.0039 n-butane................ ...... 0. 0126 0 .0095 Isopentane.................... 0.0032 0.0016 n-pentane..................... 0.0022 0.0011 Hexanes and Heavier........... 0.003& 0.0023 Experimentally determined Joule-Thom. son coefficients for natural gases afford a satisfactory means of checking the accuracy of prediction of their thermodynamic properties from the behavior of the components in the pure state and in binary mixtures. Relatively small samples of these natural gases were available, together with their analyses, and the Joule-Thomson coeffi- The Joule-Thomson coefficients were determined by measuring the change in temperature resulting from the passage of the gas through a porous thimble with a known pressure difference and under such conditions that the process was substantially isonthalpic. The details of the apparatus employed for this purpose have been described.' It is believed that the changes in temperature and pressure were ascertained with an uncertainty of not more than 0.3 per cent. However, as a result of deviations from steady flow, it is probable that uncertainties as large as 2 per cent may exist in the measured Joule-Thomson coefficient. The gases utilized in this work were taken from high-pressure separators and were dried prior to use by passage over calcium chloride at pressures in excess of 300 lb. per sq. in. The gases were subjected to the conventional fractionation and Orsat analyses. The results are recorded in Table I. The composition is typical of gases from such sources, with the possible exception of the presence of significant quantities of carbon dioxide in each of the samples. The experimental results obtained for the two natural gases are graphically Portrayed in Figs. I and 2. The experimental

Jan 1, 1943

By D. W. Fuerstenau, L. M. Berlioz

In 1957, Charles1 first presented an analysis of a relationship between the energy expended in comminution and the extent of size reduction achieved. Subsequently, Schuhmann extended and interpreted Charles' approach to comminution. According to their analysis, the energy, E, expended in comminuting unit mass of fairly uniformly-sized material is related to the size modulus of the product, k, by where a is the distribution modulus (slope of the log-log cumulative size distribution plot) and C is a constant, which is primarily determined by properties of the solid. If there is any fundamental basis for the E vs k relationship, E must necessarily be concerned with the useful work for the size reduction process and not necessarily the work input, as discussed in detail by Harris.3 Charles and numerous other investigators tested this equation only by relating k to the grinding time, assuming expended energy to be directly proportional to time, but never directly measuring power. In our laboratories, we recently constructed a special batch ball mill with which the power could be accurately determined with torque measuring apparatus.4 With this device, a direct test of the Charles relationship could then be made for ball milling. 5 EXPERIMENTAL A stainless steel mill, 11.5 in. long and 10 in. in inside diam, lined with eight low-silhouette lifter bars, was used for these experiments. The grinding media consisted of 30 kg of single sized, 1-in. diam, stainless steel balls, which occupied about 50% of the total mill volume under static conditions. The void fraction of the static ball load was approximately 0.4, and for the dry grinding conditions used, the corresponding interstitial volume was filled when about 3300 g of the dolomite feed material was present. The 7x9 mesh dolomite used as feed was obtained as a natural, uncrushed product thus as- suring a random distribution of feed particle shapes. Charge weights of 660, 1320, 1980, 2480, 3300, 3960 and 5280 g, which correspond to 20%, 40%, 60%, 80%, l00%, 120%, and 160% of the interstitial load, respectively, were used. Grinding times of 20, 40, 60, 80, 100, 150, 200 and 300 revolutions were considered, with the mill operating at 54 rpm (approximately 60% of critical speed). The tests were made sequentially, in that the size distribution obtained after a certain grinding interval was utilized as the feed for the subsequent period of grinding. Agreement with control experiments where the mill ran continuously for the entire interval was excellent. Torque measurements were made utilizing a Baldwin-Lima-Hamilton SR-4 torque pickup in the manner that has been described previously.3 Standard wet (to obtain the -400 mesh material) and dry sieving procedures were followed using the Tyler full screen series. RESULTS The Gaudin-Schuhmann size distributions obtained in all of these experiments are characterized by distribution moduli (slopes), a, of about 0.66 and are representative of normal dry batch ball milling of a material like dolomite. As an illustration of typical

Jan 1, 1968

By H. Scott

Since Bohler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar 3-2-1 obtained by increasing the maximum temperature to which the material was heated, much has been published1 connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The significant facts established by recent investigators2 are: that when the transformation occurs at the higher temperature Ar1, troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin. Previous Investigations Reviewing the work on this subject published in a recent issue of Revue de Metallurgie and referring in particular to his statement that martensite is a solution of carbide in alpha iron, Le Chatelier says :4 "How then can a theory already 20 years old demand new investigations? The reason for it is that we have not succeeded in proving directly the real presence of the transformation of iron during the very short duration of the quenching. The fall of temperature takes place at the rate of several hundred degrees per second and the observation of

Jan 1, 1920

Arizona ROBERT W. THOMAS, Chairman 'ROBERT W. HUGHES, Vice-Chairman HUBERT O. WOODS, Secretary-Treasurer American Smelting & Refining Co., Hayden, Ariz. FRANK A, WARDLAW, JR., National Director THOMAS C. CHAPMAN P. D. I. HONEYMAN CARL H. COLE JOHN E. LANNING. JOHN H. DAVIS JOHN C. LOVING EDW. G. DENTZER ALBERT MENDELSOHN MORRIS G. FOWLER BRENT N. RICKARD H. C. HENRIECHARLES F. WILLIS Black Hills BANCROFT GORE, Chairman N. P. GOODRICH, First Vice-Chairman C. N. KRAVIG, Second Vice-Chairman C E. SCHMIDT,

Jan 1, 1941

By D. D. Pollock, G. P. Conard II

Equations of the form of the Mott and Jones equations for the absolute thermoelectric powers of metals are derived primarily from a thermodynamic approach. The behaviors of transition thermoelements in common use are then examined and compared with this simple theory. MOTT and ones' derived a general expression for the absolute thermoelectric behavior of metals and alloys using the approach of the solid state physicist. This expression was then applied to specific cases.1,2 The present work develops equations of the same form principally by a thermodynamic approach. These relationships are then employed to gain some insight to the behavior of the transition thermoelements in common use. I) DERIVATION OF AN EXPRESSION FOR ABSOLUTE THERMOELECTRIC POWER First consider a metallic conductor which is maintained in a temperature gradient with no current flowing. At constant pressure, there will be a gradient of the free energy (F,) given by:

Jan 1, 1963

By R. S. McClellan

In order to meet the ever-increasing demand by consumers for uniformity of ground talc, a new method of blending its finished product has been developed by Gouverneur Talc Company, Inc., at its plant near Gouverneur, N. Y. The method has been in use for a sufficient length of time to be now judged a success. The Gouverneur district is the leading talc producing area of the world, inasmuch as more tonnage is produced there than from any other state in the U.S. or, so far as is known, from any other locality in the world. Almost all of the output goes into industrial uses, with ceramics and paint being the principal consuming industries. The physical and chemical specifications imposed by these industries are stringent and the trend, as in most industries, is toward ever increasing severity. The blending method described herein has aided Gouverneur Talc to keep up with this trend.

Jan 3, 1961

By Ralph D. Parker

A STRIKING testimonial to the value of safety was contained in an ad- dress given in May, 1936, by A. R. Young, vice-president of the United States Steel Corp.: In the period from 1906 to 1935 we have spent $24,860,540 on safety work. By comparing the cost of "prevented" accidents by the cost of settling similar accidents, we found that we had made a saving of $117,224,238. Even if those figures are 50 per cent wrong, at least we got back every dollar we paid for safety and another with it. I don't think anyone has to blush before his board of directors for an investment of that kind.

Jan 1, 1937

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938